PURPOSE PAV-EX40-UHD HDMI Extender Featuring HDBaseT Instruction Manual

PURPOSE PAV-EX40-UHD HDMI Extender Featuring HDBaseT

OVERVIEW

The PAV-EX40-UHD-KIT is an HDMI extender featuring HDBaseT technology, allowing for the extension of 4K HDMI signals up to 40 Meters. Equipped with Bi-directional POC, IR, and RS232 the PAV-EX40-UHD-KIT is an essential integrator tool for extending HDMI.

MODEL NUMBERS

• PAV-EX40-UHD-T – HDBaseT Transmitter w/ IR and RS232
• PAV-EX40-UHD-R – HDBaseT Receiver w/ IR and RS232

FEATURES

• HDMI 2.0b
• Max Resolution 4K30 4:4:4/4K60 4:2:0
• HDCP 1.X/2.2 Support
• CEC Pass-Through
• Up to 40M (Cat6a) at 4K
• Up to 70M (Cat6a) at 1080p
• Bi-Directional POC
• 3-20V IR Support with Direct Control System Support
• Bi-Directional RS232 Transport
• Supports audio formats up to uncompressed LPCM 7.1, Dolby TrueHD (including Atmos), and DTS (up to DTS:X)

PACKAGE CONTENTS

• Power Supply
• X2 IR Target (Eye/Receiver)
• X2 IR Blaster (Emitter)
• X2 Velcro Strip
• Mounting Brackets
• X2 3.5MM TRS (Stereo) to Open Cable

SPECIFICATIONS

VIDEO

AUDIO

HDBASET DISTANCE (CAT 6A)

TRANSMITTER

Power LED – Indicates that power is connected to

1. Light is On = Power Supply/POC Connected and Unit is operating
2. Light is Off = Power Supply is not connected, or no power is present

HDMI Sync LED – Indicates that an HDMI Source is connected to the Transmitter.

1. Light is On = HDMI Source is Active on the HDMI Input
2. Light is Off = HDMI Input sense no active HDMI Source

HDBaseT Link LED – Indicates that the HDBaseT Transmitter is linked with an HDBaseT Receiver.

1. Light is On = Unit has linked with an HDBaseT Receiver and is sending Data
2.  Light is Off = Unit has not linked with an HDBaseT Receiver

DIP SWITCH TABLE

RECEIVER

Power LED – Indicates that power is connected to the unit.

1. Light is On = Power Supply/POC Connected and Unit is operating
2. Light is Off = Power Supply is not connected, or no power is present

HDMI Sync LED – Indicates that an HDMI Source is connected to the Transmitter.

1. Light is On = HDMI Output is connected to an active HDMI Input
2. Light is Off = HDMI Output does not sense an active HDMI Input

HDBaseT Link LED – Indicates that the HDBaseT Transmitter is linked with an HDBaseT Receiver.

1. Light is On = Unit has linked with an HDBaseT Transmitter and is receiving Data
2. Light is Off = Unit has not linked with an HDBaseT Transmitter

RS232 CONFIGURATION

• RS232 can be used to pass control signals bi-directionally between any two RS232 compatible devices. Commonly used in extending control from a control system
• The RS232 ports on the PAV-EX40-UHD-KIT are pinned null modem:

IR CONFIGURATION

IR COMMUNICATION CAN BE SENT TWO WAYS

1. Downstream (From transmitter)
2. Plug an IR Receiving Eye or Control System IR output direct into the IR Sensor port of the PAV-EX40-UHD-T to pass infrared signals to the IR Out port on the Receiver
3. Set IR Dipswitch according to input signal device
4. Connect the IR Out Port of the Receiver to an IR Emitter or Direct IR Input
5. Upstream (From Receiver)
6. Plug an IR Receiving Eye into the IR Sensor port of the PAV-EX40-UHD-R to pass infrared signals to the IR Out port on the Transmitter
7. Connect the IR Out Port of the Transmitter to an IR Emitter or Direct IR Input
8. IR Input (Receiving Eye) (Dipswitch 5 = 0)
9. IR Direct Input from Control System (Transmitter Only) (Mono Tip to Tip/Sleeve to Sleeve) (Dipswitch 5 = 1)
10. IR Output to Emitter

TROUBLESHOOTING

1. No Power LED
2. Ensure PSU is sending proper voltage
3. If using POC, ensure that the unit sending POC is connected to power
4. If using POC, try powering the unit direct to ensure unit operates stand alone
5. No HDMI LED
6. Plug Source direct into display to ensure operability
7. Change the resolution of the source device to 1080p or 4K30 (No HDR)
8. Set a canned EDID. Source may require power cycle
9. Swap HDMI cable between Transmitter and Source. HDMI Handshakes with cables under 2 Meters may not sync properly
10. No HDBT Link
11. Check cable Length. Max Distances are 40M at 4K or 70M at 1080p. HDBaseT Recommends Cat 6A; Cat 6 and Cat 5e may experience a 5-20% loss of distance
12. Remove Excess Service Loops and Bundles of Cable. HDBaseT Recommends up to 6 runs of Cat in a single bundle
13. Bypass all patch-panels and punch down blocks
14. Re-terminate connectors. IP Continuity testers may indicate correct pinouts; However, HDBaseT Signals are transmitted differently than Ethernet Signals

RS232 TRANSMISSION

• Ensure correct pinout between both the transmitter and receiver side. A null modem adaptor may be used for quick pinout changing
• If sending downstream, ensure dipswitch is in the correct position for Input device type
• The Visible IR Emitters can be used to ensure signal is being sent from one point to the other

www.purposeav.ca support@purposeav.ca (888) 470.2211

References

• Home · Purpose AV

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>