SEALEY VS921 IR & RF Key Fob Tester Instructions
- June 5, 2024
- SEALEY
Table of Contents
INSTRUCTIONS FOR
IR & RF KEY FOB TESTER
MODEL NO: VS921
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instructions
- SAFETY
‰ WARNING! Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
√ Familiarise yourself with the applications, limitations, and potential hazards of the tester.
√ Keep the tester clean and in good condition.
√ Protect the tester from the following: Static electricity, High temperatures.
× DO NOT get the tester wet or use in damp or wet locations or areas where there is condensation.
× DO NOT use the tester for any purpose other than for which it is designed.
× DO NOT allow untrained persons (particularly children) to operate the tester.
DO NOT operate the tester when you are tired or under the influence of alcohol, drugs or intoxicating medication.
INTRODUCTION
Detects and confirms radio frequency and/or infra red emission from key fobs and remote controls. Helps diagnose faults quickly and easily without the need to dismantle the fob, remote or vehicle. Magnetic backing sticks to the side of any ferrous surface making distance test of transmitter a possibility. Suitable for a wide variety of vehicle and electronic/electrical applications. Powered by a 9V battery (not included).
SPECIFICATION
Model no: ………………………………………………………….. VS921
Detects:……………………………… Infra-red or Radio Frequency
RF: ……………………………….. 418MHz, 433-434MHz, 868MHz
OPERATION
-
ASSEMBLY
-
Slide the battery cover off from the rear of the tester.
-
Insert a 9V/PP3 battery (not included).
-
Make sure polarity is correct.
-
Replace battery cover.
-
OPERATION
-
Switch the unit on by pressing the “ON/OFF” button, this will illuminate the green LED at the top of the tester.
-
Secure the tester to a metal surface using the magnetic pad on the rear of the tester.
-
Make sure the tester is at least 3 metres away from other electrical devices which may emit an electrical frequency. Interference with the unit will cause the LED to illuminate/flash.
-
Aim a working key fob at the tester and operate the key fob, a LED at the top will flash once. Now test the suspect key fob.
-
If the suspect key fob does not trigger the LED, change the key fob’s battery and repeat the procedure.
-
The tester can also be used to determine the strength/range of a key fob’s signal.
Note: The tester need not be switched off as it has an “auto-shutdown” function (approximately 1 minute without use). -
This tester can also pick up test home entertainment remotes and other similar devices.
Environmental Protection
****Recycle unwanted materials instead of disposing of them as waste. All
tools, accessories and packaging should be sorted, taken to a recycling centre
and disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain off any
fluids (if applicable) into approved containers and dispose of the product and
the fluids according to local regulations.
WEEE Regulations
Dispose of this product at the end of its working life in compliance with the
EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the
product is no longer required, it must be disposed of in an environmentally
protective way. Contact your local solid waste authority for recycling
information.
Battery Removal
Refer to section 4.1 for battery removal instructions. Under the Waste
Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to
inform potential purchasers of products containing batteries (as defined
within these regulations), that they are registered with Valpak’s registered
compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number
(BPRN) is BPRN00705.
NOTE: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will
be required for any claim.
Sole UK Distributor, Sealey Group.
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk. IP32 7AR
01284 757500
01284 703534
Web: www.sealey.co.uk
sales@sealey.co.uk
© Jack Sealey Limited
Original Language Version
VS921| Issue 3(I) 20/01/17
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>