EUROPRO 30830 Compact-Pro Joint 20 User Manual

: June 5, 2024
: EUROPRO

Table of Contents

EUROPRO 30830 Compact-Pro Joint 20
USER MANUAL
WARNING
YOUR MACHINE
USE OF THE MACHINE
CLEANING PROCEDURE
DEFECTS AND REMEDIES
DECLARATION OF CONFORMITY
WARRANTY CONDITIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EUROPRO 30830 Compact-Pro Joint 20

USER MANUAL

IMPORTANCE OF THE MANUAL
This manual is a key part for the use of your machine. It summarizes the procedures of starting-up, cleaning and maintenance of the device and also the safety instructions you need to observe. Read carefully all the working and safety instructions and the warnings included in this manual before starting your machine. Most of the accidents are caused by non-compliance of the safety standards and rules. This manual must be kept near the machine, within reach of the user and held in good condition until the final destruction of the machine. In case of loss or deterioration of the manual, you can ask the machine manufacturer mentioned on page 4 for a copy at any moment.

RECEIVERS OF THE MANUAL
This manual is intended to any staff which will manipulate the machine :

people in charge of the transport of the machine
people in charge of the use of the machine
people in charge of the cleaning and maintenance of the machine
people in charge of the final destruction of the machine

WARNING

SAFETY

Using the machine in an incorrect way or in non-compliance of the safety instructions indicated in this manual can cause death or serious injuries.
Read carefully all the working and safety instructions and the warnings contained in this manual before starting your machine.

Respect all the safety standards before running the equipment.
Use the equipment only for the applications specified in the manual.
Always remain alert when using the equipment.
Transport the machine using the handles or the appropriate grips.
During the breaks, disconnect electrically the machine.
Run the equipment to its nominal voltage.
Let at least 50 cm of free space between the equipment and any obstacle so that the air flow is not blocked.
Know how to quickly stop the equipment in case of necessity.
Never use the equipment while it is running abnormally or it is defective.
Do not direct a water jet or flammable liquid on the machine.
Never direct an air jet or product jet on a person or an animal.
Do not touch warm surfaces of the equipment.
Always wear adequate body protections (glasses, gloves, overall and mask) and pay attention to long hair.
Never touch moving parts.
Do not insert any object or the hands inside the protection grids to avoid any accident or damage to the machine.
For any outside job, only use appropriate extension cords.
Maintain the equipment carefully and clean it properly after every use.
Disconnect the equipment before any intervention.
Avoid absolutely to unscrew any connection while the machine is under pressure.
Check the damaged parts.
Do not clean the plastic parts with solvant.
In case of damage of the electric cable or the plug, do not run the machine and contact a licensed After-Sale Service to put genuine parts instead of the defective ones.
In case of needed After-Sale Service, always specify the machine model and its serial number.
For any replacement of parts, only use genuine parts.
Do not modify the machine.
Do not cut or dismantle the protection grids.
Do not open the electric box.

WORKSPACE

Maintain the workspace clean and clear.
Ambient operating temperature must be from 5°C and 35°C.
Do not use the equipment in a potentially explosive area.
Do not place any potentially inflammable objects in close proximity to the machine.
Take away every not qualified person from the working area of the machine, as well as children and animals.
In case of installation of the machine on scaffolding or a plan above ground level, attach the machine to avoid any fall while operating.
Do not install the equipment on an inclined surface to avoid the risks of unexpected moves or falls.

HOSES

Always use hoses and connections adapted to the used product (genuine parts), do not try to fix it.
Do not walk on the hoses, do not bend them.
Do not use the hoses to pull the machine.

STORAGE

Keep the equipment in a clean and clear area in which the temperature does not exceed +35°C.
After every use, necessarily grease the pump with a mixture of water + storage liquid to avoid it blocking up. The storage of a not greased pump can damage it seriously.

ELECTRIC CONNECTION

The electric connection of the machine must be on a 16A – 230V plug with a differential circuit breaker. Before any intervention on the machine, make sure that every energy supply is cut (air and electricity).

GROUND CONNECTOR
All the machines must be connected to the ground when they work to protect the operator from electric shocks. Our machines are all equipped with standardized connection plugs. Electric connection must be made by a qualified technician. It is fobidden to modify or dismantle the machine, especially the electric box. Repairs must be made by an authorized center or our After-sale Service. During any intervention on the machine, make sure that the ground is well reconnected.

EXTENSION CORDS
During the use of an extension cord, make sure that it is not crushed or damaged and that it contains a ground. Check that the section of the used extension cord is sufficient to support the machine when it is working. A too thin extension cord can cause voltage drops or overheating of the machine. In case of use of a cable reel, it is imperative to unwind it entirely, otherwise, the equipment can be damaged. The section must be proportional to the length of the cord.

END OF LIFE OF THE PRODUCT

At its end-of-life, the machine must not be eliminated with the other household waste. The uncontrolled elimination of waste can harm the environment or human health. Individuals are invited to contact the distributor which sold them the product or to inquire with their city hall to know where and how to get rid of the product so it can be recycled while respecting the environment. Under the regulation of Waste of Electrical and Electronic Equipments (WEEE), we undertake to process the used EEEs according to the following provisions: applicable only to products on the market since 08/13/05, under the brands EUROPE PROJECTION or VOLUMAIR, products of other brands sold by our company (upon presentation of the corresponding invoices), products that operate using electrical energy (for example, thermal washers or compressors do not fall into this category).

Treatment modality
WEEE returns collected by our clients/distributors at their own expense to our collection points in Antony (92) or Rousset sur Arc (13). Upon receipt, the products are sorted by our employees and directed to the most appropriate processing channels. For any further information, please contact our hotline +33 4 42 29 08 96 or conseil@euromair.com.

YOUR MACHINE

DESCRIPTION
Special stone, brick, flagstone grouting jobs machine, equipped with a stainless steel tank. Easy and quick start-up an cleaning, due to its drain plug and quick-disassembly pump.

TECHNICAL CHARACTERISTICS

IDENTIFICATION OF THE COMPONENTS

A Product outlet
B Rotor / Stator
C Manometer
D Lance
E Nozzle
F Drain plug
G Automatic lubricator
H Control panel (see next page)

USE OF THE MACHINE

PREREQUISITES

The electric connection has to be 230 V – 16 A – 50 or 60 Hz with a 3 x 2,5 mm² cable reel of 40m maximum, completely unreeled.
One push on the MANU/AUTO button (2) makes the pump start working and the (L2) light lights up.
One push on the button REVERSE (3) makes the product pump turn in reverse mode and the light (L4) lights up.
In AUTO mode, the pump starts only at the opening of the lance.
In MANU mode, the pump works continuously.
After a prolonged standstill, it is possible that the pump might be blocked. If this is the case, alternately turn the pump forwards and backwards for 5 second sequences. As soon as the engine starts to turn normally, the pump is unblocked.
Check every month that the machine’s automatic lubricator is working properly. The level of grease in the cartridge should decrease steadily. The absence of grease can seriously damage the machine.

PRESSURE VALUES:

Ready-to-use product: from 12 to 15 bars
Traditional product: from 5 to 8 bars

PRESSURE CONTROL AND ADJUSTMENT: (at least once a week)

Install the pressure controller on the machine outlet with the valve in the open position.
Put water in the tank.
Switch the machine on (button (1)).
Set the machine to 100% using buttons (4) & (5).
Press MANU/AUTO (2), the machine starts.
Close the controller valve and read the value on the manometer (C).
Adjust the desired value with the 3 pump screws (tighten from the external screw to the screw on the tank side, equally).
Adjust by closing the valve and reading the manometer (repeat the adjustment operation until the correct pressure is obtained).

STARTING UP

Install the machine on a flat floor.
Connect electrically (16 A minimum plug, extension cable 40m maximum in 3 x 2,5 mm² minimum).
Connect the hose (and its extension if necessary).
Put water into the tank.
Switch on the machine (button (1)).
Set the motor speed to 40% using buttons (4) & (5).
Press MANU/AUTO (2), the machine starts.
Wait until the water comes out of the hose (or the tank is emptied).
Press MANU/AUTO (2), the machine stops.
Empty the water from the hose and drain the remaining water from the tank using the drain plug (F).
Connect the lance in open position without the nozzle.
Fill the tank with product. Press MANU/AUTO (2), the machine starts.
Check that the hose does not clog (check the pressure on the manometer (C)) and that the product descends correctly.
When the product comes out of the hose, press MANU/AUTO (2) to stop the machine and THEN close the lance.
Install the desired nozzle at the end of the lance.
Connect remote control cable.
Adjust the machine speed depending on the desired flow rate.
When the lance is opened, the machine will start.

ERROR CODES
The different error codes show up on the display (J). EUROPRO-30830
-Compact-Pro-Joint-20-3

CLEANING PROCEDURE

Empty the tank to the maximum without adding water inside.
Disconnect the remote control cable.
Open the hose to relieve pressure from the product hose and press REVERSE (3) for 10 to 20 seconds.
Clean the accessories first (lance, nozzle, etc.).
Clean the tank (remove the plug (F) to allow water to drain, never run water through the full product hose).
Fill the tank with clean water.
Disconnect the product hose, press MANU/AUTO (2) to discharge any product remaining into the pump.
Place the cleaning ball in the product outlet (A) and replace the hose.
Set machine speed to 40%.
Start the machine by pressing MANU/AUTO (2).
When the ball comes out of the hose, press MANU/AUTO again to stop the machine.
Repeat operations 7 to 11 until water comes out of the hose clean.

DEFECTS AND REMEDIES

EUROPRO-30830-Compact-Pro-
Joint-20-4

DECLARATION OF CONFORMITY

THE MANUFACTURER: EUROPE PROJECTION 228, avenue Olivier Perroy 13790 ROUSSET
DECLARES THAT THE EQUIPMENT DESIGNATED BELOW:
- Trademark: EUROPE PROJECTION
- Type: Spraying machine
- Model: COMPACT-PRO JOINT 20

COMPLIES WITH THE DIRECTIVES:

Machines 2006/42/CE
Low voltage 2014/35/UE
CEM 2014/30/UE
ROHS 2011/65/UE

WARRANTY CONDITIONS

Each equipment is delivered inspected and tested.
We exclude any warranty for visible defects, not notified by the customer within 48 hours. The equipment sold is guaranteed during the manufacturer’s warranty from the date of purchase, as specified on the original proof of purchase, and under the conditions defined by the manufacturer. This warranty covers any equipment against any manufacturing or material defect, under normal conditions of use. Insofar as the customer is presumed to be a professional of the same field of specialty, this warranty covers only the defect of conception of the equipment rendering it unfit for its use, which could not be detected by a professional buyer. The defects or deteriorations caused by natural wear, external accident or a modification, use, storage or treatment of the equipment not planned by the manufacturer, nor specified by ourselves, are excluded from any warranty. Are expressly excluded from the warranty the defects resulting from an improper use, the application of abrasive or corrosive products, an inappropriate installation, the negligence, an insufficient maintenance or cleaning, inappropriate conditions of storage, chemical, electronical or electric influences, any change in the normal process of use. The following wearing parts are not covered by the warranty (non-exhaustive list): rotors, stators, driving shafts, connecting rods, seals, cleaning balls, spray guns, lance, nozzle, hose, needle kits, cylinders, piston rods, prime/spray valve assy, seal kits, membranes, suction and delivery valves, carding machine vanes, filters, oils, chains and quick- release clip. The warranty also excludes the equipment on which the serial number was erased or made illegible, on which unauthorized people made attempts of repair, which were totally or partially dismantled. Our equipment are covered by a manufacturer’s warranty (parts and labor) of 12 months following the purchase date by the final customer, without exceeding 24 months from the date of purchase by the client. The final user can extend this manufacturer’s warranty for a further 12 months by filling in the warranty extension form on our website www.euromair.com (under After-Sale Service) within 4 weeks of purchase. This manufacturer’s warranty and its extension shall automatically cease if the customer does not resell the equipment within 24 months of its purchase. The cases of exclusion of warranty mentioned in articles above are also applicable to our own equipment. The manufacturer’s warranty shall always be subject to the presentation of the purchase invoice. If the defective equipment is covered by the manufacturer’s warranty, it shall be repaired or replaced at our discretion free of charge. If the defective equipment is not covered by the manufacturer’s warranty, we shall issue a quote for the repair that we shall submit to the customer for approval. Except as otherwise required by law, this manufacturer’s warranty is exclusive of all other warranties, including the statutory warranty of hidden defects. In case of intervention of our services on a breakdown caused by the customer or an incident excluded in the conditions referred to above, the costs of repair and transport shall be invoiced to the customer. We exclude all liability for indirect damages suffered by the customer, such as, but not limited to, loss of income, turnover, loss of profits, loss of image, of any kind whatever. In all cases, our liability shall be limited to the amount paid by the customer for non-compliant equipment. Any legal action of the customer against us relating to the warranty of the equipment shall be barred 1 year after the date of discovery of the defect. The customer shall have to prove the date of this discovery.

Request for Warranty
For any request related to the repair of an equipment covered by the manufacturer’s warranty, the customer shall have to fill the warranty form, available on our website to the following address: https://www.euromair. com/en/after-sales-service/ For a full dossier, the following documents shall have to be attached:

the purchase invoice of the final user
pictures of the defective parts of the equipment
a description of the breakdown
the quote of labor if the customer is certified by EUROMAIR for repairing the equipment

No invoice of labor shall be taken into account without our prior approval.

Analysis of the breakdown by our technical department
A file number shall be given to the customer and an answer shall be provided within 48 working hours after reception, provided that the request for warranty is considered as full. In the event the equipment is covered by the manufacturer’s warranty, we shall confirm the warranty to the customer and send him a quote (without price) detailing the parts to be changed and any comments.

Return of replacement parts
Replacement parts must be ordered with a warranty agreement number and will be made available to the customer at our factory. The conditions of return of the equipment are detailed in our Delivery terms. In the case of a warranty claim on an on-board component such as a Kohler, Honda or Vanguard engine in a machine manufactured by us, only the manufacturer of the component is able to validate the warranty coverage.
In this case, the request must be addressed directly to the manufacturer of the component or to its nearest authorised representative. The Euromair, Euromair MPC or Mixer service centres may be considered as the manufacturer’s representatives if they are the closest. As this principle also applies to batteries, our supplier Parts Holding Europe, or one of its sister companies, remains your contact for your requests (https://www. partsholdingeurope.com/).