EUROPRO JETPRO 120-7 Spraying Machine User Manual

JETPRO 120-7 Spraying Machine
User Manual

You just acquired one of our machines and all the team of Europe Projection thanks you for the confidence you have granted us. Manufacturer of professional equipment for paint and fillers, we have put our know-how for 25 years at the service of the users of our machines. Our technical & commercial team is at your disposal for any further information you may need about the machine you just acquired.

EUROPE PROJECTION
228, avenue Olivier Perroy 13790 ROUSSET
Tél : +33 (0)4 42 29 08 96 contact@euromair.com

USER MANUAL

IMPORTANCE OF THE MANUAL
This manual is a key part of the use of your machine. It summarizes the procedures for starting up, cleaning, and maintenance of the device and also the safety instructions you need to observe.
Read carefully all the working and safety instructions and the warnings included in this manual before starting your machine. Most accidents are caused by non-compliance with the safety standards and rules.
This manual must be kept near the machine, within reach of the user, and held in good condition until the final destruction of the machine. In case of loss or deterioration of the manual, you can ask the machine manufacturer mentioned on page 4 for a copy at any moment.

RECEIVERS OF THE MANUAL
This manual is intended for any staff who will manipulate the machine:

• people in charge of the transport of the machine
• people in charge of the use of the machine
• people in charge of the cleaning and maintenance of the machine
• people in charge of the final destruction of the machine

WARNING

SAFETY
Using the machine in an incorrect way or in non-compliance with the safety instructions indicated in this manual can cause death or serious injuries. Read carefully all the working and safety instructions and the warnings contained in this manual before starting your machine.

• ****Respect all the safety standards before running the equipment.
• Use the equipment only for the applications specified in the manual.
• Always remain alert when using the equipment.
• Transport the machine using the handles or the appropriate grips.
• During the breaks, disconnect electrically the machine.
• ****Run the equipment to its nominal voltage.
• Let at least 50 cm of free space between the equipment and any obstacle so that the airflow is not blocked.
• Know how to quickly stop the equipment in case of necessity.
• Never use the equipment while it is running abnormally or it is defective.
• Do not direct a water jet or flammable liquid on the machine.
• Never direct an air jet or product jet on a person or an animal.
• Do not touch the warm surfaces of the equipment.
• Always wear adequate body protection (glasses, gloves, overalls, and mask) and pay attention to long hair.
• Never touch moving parts.
• Do not insert any object or the hands inside the protection grids to avoid any accident or damage to the machine.
• For any outside job, only use appropriate extension cords.
• Maintain the equipment carefully and clean it properly after every use.
• ****Disconnect the equipment before any intervention.
• Avoid absolutely unscrewing any connection while the machine is under pressure.
• Check the damaged parts.
• Do not clean the plastic parts with solvent.
• In case of damage of the electric cable or the plug, do not run the machine and contact a licensed After-Sale Service to put genuine parts instead of the defective ones.
• In case of needed After-Sale Service, always specify the machine model and its serial number.
• For any replacement of parts, only use genuine parts.
• ****Do not modify the machine.
• Do not cut or dismantle the protection grids.
• Do not open the electric box.

WORKSPACE

• Maintain the workspace clean and clear.
• The ambient operating temperature must be from 5°C and 35°C.
• Do not use the equipment in a potentially explosive area.
• Do not place any potentially inflammable objects in close proximity to the machine.
• Take away every not qualified person from the working area of the machine, as well as children and animals.
• In case of installation of the machine on scaffolding or a plan above ground level, attach the machine to avoid any falls while operating.
• Do not install the equipment on an inclined surface to avoid the risks of unexpected moves or falls.

HOSES

• Always use hoses and connections adapted to the used product (genuine parts), do not try to fix it
• Do not walk on the hoses, do not bend them.
• Do not use the hoses to pull the machine.

STORAGE

• Keep the equipment in a clean and clear area in which the temperature does not exceed +35°C.
• After every use, necessarily grease the pump with a mixture of water + storage liquid to avoid it blocking up. The storage of a not greased pump can damage it seriously.

IN CASE OF NECESSITY, WE SAVE OURSELVES THE RIGHT TO MAKE ANY USEFUL MODIFICATION WITHOUT ADVANCED NOTICE.

ELECTRIC CONNECTION
The electric connection of the machine must be on a 16A – 230V (400V for JETPRO 1307) plug with a differential circuit breaker. Before any intervention on the machine,  ake sure that every energy supply is cut (air and electricity).

GROUND CONNECTOR
All the machines must be connected to the ground when they work to protect the operator from electric shocks. Our machines are all equipped with standardized connection plugs.
The electric connection must be made by a qualified technician. It is forbidden to modify or dismantle the machine, especially the electric box. Repairs must be made by an authorized center or our After-sale Service. During any intervention on the machine, make sure that the ground is well reconnected.

EXTENSION CORDS
During the use of an extension cord, make sure that it is not crushed or damaged and that it contains ground. Check that the section of the used extension cord is sufficient to support the machine when it is working. A too thin extension cord can cause voltage drops or overheat of the machine. In case of use of a cable reel, it is imperative to unwind it entirely, otherwise, the equipment can be damaged. The section must be proportional to the length of the cord.

END OF LIFE OF THE PRODUCT
At its end of life, the machine must not be eliminated with the other household waste. The uncontrolled elimination of waste can harm the environment or human health. Individuals are invited to contact the distributor which sold them the product or to inquire with their city hall to know where and how to get rid of the product so it can be recycled while respecting the environment.
Under the regulation of Waste of Electrical and Electronic Equipment (WEEE), we undertake to process the used EEEs according to the following provisions: applicable only to products on the market since 08/13/05, under the brands EUROPE PROJECTION or VOLUMAIR, products of other brands sold by our company (upon presentation of the corresponding invoices), products that operate using electrical energy (for example, thermal washers or compressors do not fall into this category).
Treatment modality
WEEE returns are collected by our clients/distributors at their own expense to our collection points in Antony (92) or Rousset sur Arc (13). Upon receipt, the products are sorted by our employees and directed to the most appropriate processing channels.
For any further information, please contact our hotline to conseil@euromair.com or +33 4 42 29 08 96.

YOUR MACHINE

DESCRIPTION
Machine for applying thin films of filler. It uses a valveless pump and is easy to maintain, with a round stainless steel tank for easy cleaning, and a Ø35 mm drain valve. It is equipped with a large diameter, flat profile, and inflatable tires for better stability.
APPLICATIONS
All types of ready-to-use film plaster: smoothing coating, raking coating, casing coating, bituminous coating … Can also make droplet-type applications with an optional kit and a compressor.
Do not use products with grain size, mortars, lime-based renders, technical or special coatings with heavy loadings.

TECHNICAL CHARACTERISTICS

| Jetpro 100-7| Jetpro 120-7| Jetpro 130-7
---|---|---|---
Max. working pressure| 120 bar| 130 bar
Max. product flow-rate| 6 L/min| 7 L/min| 9 L/min
Electric motor| 2,2 kW| 3 kW| 4 kW
Power| 230 V / 50 & 60 Hz| 400 V Tri / 50 & 60 Hz
Type of pump| volumetric screw
Pump| JET 2| JET 3| JET 5
Tank capacity| 110 L
Max. nozzle size (new)| 0,045″| 0,055″| 0,065″
Dimensions (L x w x h)| 143 x 65 x 97 cm
Weight| 90 kg| 100 kg| 110 kg
Noise level| 91 Lwa
Delivered with| – a Ø16 x 20 m hose
– a TT3 439 nozzle| – a Ø19 x 30 m hose
– a Ø16 x 2,5 m easy handling flexible hose
– a TT3 443 nozzle
– a Jethro spray gun with nozzle holder
– a toolbox containing:
• two spanners 17 and 22
• a multi-grip plier
• three Allen keys Ø2, 5 and 8
• two cleaning balls and a cleaning brush
• 1 L of storage liquid

IDENTIFICATION OF THE COMPONENTS

USE OF THE MACHINE

PREREQUISITES

• The electric connection has to be 230 V – 16 A – 50 or 60 Hz with a 3 x 2,5 mm cable reel of 40m maximum completely unreeled (400 V for JETPRO 130-7).

• The display (A1) indicates the setting of the speed of the rotation of the pump in %. Below 40%, the machine is in PRIMING mode.

• During the starting up of the machine, it is important to respect the following stages mentioned below:
  – turn the machine on
  – Press the button (1)
  – set the display (A1) to 30 with help of the buttons +/- (4) & (5)
  – put soapy water into the tank
  – Press the button (2) to verify the correct start-up

• After a prolonged standstill, it is possible that the pump might be blocked. If this is the case:
  – Put soapy water into the tank. Set the speed to 1. Switch the machine on. As soon as the motor starts to run normally, the pump is unblocked. Empty the water.
  – If the pump is still blocked, put soapy water liquid into the tank. Alternately turn the pump forwards and backward for 5-second sequences. As soon as the engine starts to turn normally, the pump is unblocked. Empty the water.
  ****Never run the pump without water or product.
  Never use petroleum-based products in the pump, as they may damage it.

• Check every month that the machine’s automatic lubricator is working properly. The level of grease in the cartridge should decrease steadily. The absence of grease can seriously damage the machine.
  It is imperative to replace the automatic motor flange lubricator (F) every 6 months.
  It is essential to grease the threads of the pump nose (A), the filter holder (B) and the gun inlet and outlet (G). The absence of grease can cause the threads to seize up and wear out prematurely.
  ****Do not use tools to screw or unscrew the filter holder cap (B), the hose on the pump side (A) and gun side (G) and the nozzle holder. Perform this operation by hand to avoid damaging the parts.

WORK / STOP

• Once the machine is plugged in, the machine is in the stop mode, the display (A1) indicates OFF and
  the display (B1) indicates the mains voltage.

• If AU is indicated, unscrew the emergency stop button a quarter of a turn.

• With one push of the button ON/OFF (1), the light (L1) lights up, the machine is ready to work.

• One push of the button ON/OFF (1), when the machine is ready to work (light (L1) is on), the machine
  will switch off, and the display (A1) indicates OFF (light (L1) is off).

STARTING UP – USE OF PLASTER/PAINT

1. Put soapy water into the tank.

2. Press button (1) to switch the machine on.

3. Open the spray-gun, without a nozzle or nozzle holder.

4. Set the pump speed to 30 using buttons (4) & (5).

5. Press the button (2), and the screw at the bottom of the tank shall turn (if it does not turn, see procedure 4.1.)

6. When the water comes out of the spray gun, press button (2) to stop the machine.

7. Empty the water remaining in the tank by opening the drain valve (E).

8. Pour the plaster or paint into the tank. If necessary, use a trowel or tool to push the product under the grid to eliminate air bubbles. Always keep the product level in the tank above the grid.
   Remember to mix the product well before pouring it into the machine’s tank.

9. Still at speed 30, press the button (2) and wait until the product comes out of the spray gun.

10. As soon as the product comes out of the spray gun, press button (2) again, then close the spray gun.

11. Install the nozzle holder and the nozzle adapted to the product used.

12. Set the pressure to 70 minimum using buttons (4) & (5).

13. Press button (2), and the machine runs for a few seconds and then stops.

14. The machine is ready to spray, it will start automatically when the spray gun is opened.

15. Adjust the pressure according to your needs using buttons (4) & (5).

The machine is equipped with a safety system to prevent damage to the rotor/stator. If the machine fails to reach its set pressure, it will automatically stop after 45 seconds.  There are two possible scenarios:

• The nozzle used is either too big or worn: reduce the nozzle size or replace it with a new one.
• The rotor/stator is worn out: reduce the working setpoint and plan to replace the rotor/stator.

STARTING UP – USE OF DROPLET

For droplet applications, it is imperative to use a suitable compressor.
If in doubt about which compressor to use, contact our services: +33 4 42 29 08 96.

1. Put soapy water into the tank.

2. Press button (1) to switch the machine on.

3. Make sure that the box for droplets is not connected.

4. Open the lance, without a nozzle.

5. Set the pump speed to 30 using buttons (4) & (5).

6. Press the button (2), and the screw at the bottom of the tank shall turn (if it does not turn, see procedure 4.1.)

7. When the water comes out of the lance, press button (2) to stop the machine.

8. Empty the water remaining in the tank by opening the drain valve (E).

9. Pour the plaster into the tank. If necessary, use a trowel or tool to push the product under the grid to eliminate air bubbles. Always keep the product level in the tank above  the grid.
   Remember to mix the product well before pouring it into the machine’s tank.

10. Still at speed 30, press the button (2) and wait until the product comes out of the lance.

11. As soon as the product comes out of the lance, turn the button (2) again, then close the lance.

12. Install the nozzle holder and the nozzle adapted to the product used.

13. Set the speed to 10 (buttons (4) & (5)).

14. Connect the starter box to the machine plug (J).

15. Connect the air hose between the compressor and the box, and then the hose between the box and
    the lance.

16. Start the compressor.

17. Press button (2), and the machine runs for a few seconds and then stops.

18. The machine is ready to spray, it will start automatically when the lance is opened.

19. Adjust the product flow rate using the buttons (4) & (5) and the air with the control valve mounted on the lance.
    The machine is equipped with a safety system to prevent damage to the rotor/stator. If the machine fails to reach its set pressure, it will automatically stop after 45 seconds.  There are two possible scenarios:
    – The nozzle used is either too big or worn: reduce the nozzle size or replace it with a new one.
    – The rotor/stator is worn out: reduce the working setpoint and plan to replace the rotor/stator.

ERROR CODES
The different error codes show up on the display (A1).

supply is 230 V, and verify the fuse in the electric box.
| The emergency stop is on.| Unlock the emergency stop button (AU).
| The machine is in stop mode.| Switch the machine on by pressing the button (1).
| Default control engine.| Set the machine to OFF for one minute and then switch it back on.

If the problem persists or if in doubt about the good running of the machine, do not try to repair it by yourself or to dismantle it.
Contact an authorized After-Sale Service or our hotline: +33 4 42 29 08 96.

DEFECTS AND REMEDIES

blocked. See procedure 4.1. page 10.
The pressure is insufficient.| • Verify that the setting is strong enough.
• Verify that the nozzle is not too big or worn out.
• Verify the wear of the pump.

In case of an unknown defect or a doubt about the good running of the machine, do not try to repair it by yourself or to dismantle it.
Contact an authorized After-Sale Service or our hotline: +33 4 42 29 08 96.

CLEANING PROCEDURE

AFTER PLASTER/PAINT USE
Before unscrewing the hose, make sure it is not under pressure anymore.

1. Remove the nozzle and place it in a bucket of water.
2. With the spray gun, speed to 30, and press button (2) to empty the tank to the maximum.
3. Press button (2) again to stop the machine.
4. Open the valve (E) and proceed to the cleaning of the tank. Once the tank is clean, close the valve (E).
5. Put water with a little liquid soap in the tank.
6. Remove the filter from its housing (B) and clean it.
7. Disconnect the product hose from the pump nose (A).
8. Set the speed to 30, and turn the machine on for 30 seconds to clean the pump.
9. Stop the machine (button (2)) and finish cleaning the pump nose (filter + product outlet).
10. Disconnect the spray gun from the hose.
11. Put the cleaning ball in the hose and reconnect it to the machine.
12. Still, at speed 30, turn the machine on, and the product starts to come out.
13. When the ball comes out of the hose, repeat the operation.
14. Clean the spray gun, then put it back at the end of the hose.
15. Replace the nozzle and turn it to the unclogging position.
16. Turn the machine on for 30 seconds to clean the nozzle.
17. Open the valve (E) to empty the water remaining in the tank, then close the valve.
18. Put some water with storage liquid back into the tank (up to the level of the grid).
19. With the spray gun open, still at speed 30, switch on for about one minute.
20. The machine is clean. Before storing it, make sure that there is still some water/storage liquid mixture at the bottom of the tank.
    The direct projection of water under pressure onto the control panel has to be stopped at the risk of water infiltration into the electric box. Proceed by simply cleaning with a humid sponge.

MACHINE DECLARATION OF CONFORMITY

THE MANUFACTURER: EUROPE PROJECTION
228, avenue Olivier Perry 13790 ROUSSET

DECLARES THAT THE EQUIPMENT DESIGNATED BELOW :
Trademark: EUROPE PROJECTION
Type: Atomizer
Model: JETPRO 100-7, 120-7, 130-7

COMPLIES WITH THE DIRECTIVES:

• Machines 2006/42/CE
• Low voltage 2014/35/UE
• CEM 2014/30/UE
• ROHS 2011/65/UE

ROUSSET, JANUARY 20th 2022
Patrick BOREL
President

SPRAY-GUN DECLARATION OF CONFORMITY

THE MANUFACTURER: EUROPE PROJECTION
228, avenue Olivier
Perry
13790
ROUSSET
DECLARES THAT THE EQUIPMENT DESIGNATED BELOW:
Trademark: EUROPE PROJECTION
Model: Spray-gun
Working pressure: 19 MPa
COMPLIES WITH THE DIRECTIVE:

• Machines 2006/42/CE

ROUSSET, JANUARY 20th 2022
Patrick BOREL
President

WARRANTY CONDITIONS

Each piece of equipment is delivered inspected and tested.
We exclude any warranty for visible defects, not notified by the customer within 48 hours.
The equipment sold is guaranteed during the manufacturer’s warranty from the date of purchase, as specified on the original proof of purchase, and under the conditions defined by the manufacturer.
This warranty covers any equipment against any manufacturing or material defect, under normal conditions of use. Insofar as the customer is presumed to be a professional of the same field of specialty, this warranty covers only the defect of the conception of the equipment rendering it unfit for its use, which could not be detected by a professional buyer.
The defects or deteriorations caused by natural wear, external accident or a modification, use, storage or treatment of the equipment not planned by the manufacturer, nor specified by ourselves, are excluded from any warranty.
Are expressly excluded from the warranty the defects resulting from improper use, the application of abrasive or corrosive products, an inappropriate installation, negligence, insufficient maintenance or cleaning, inappropriate conditions of storage, chemical, electronic or electric influences, any change in the normal process of use.
The following wearing parts are not covered by the warranty (non-exhaustive list): rotors, stators, driving shafts, connecting rods, seals, cleaning balls, spray guns, lance, nozzle,  hose, needle kits, cylinders, piston rods, prime/spray valve assy, seal kits, membranes, suction and delivery valves, carding machine vanes, filters, oils, chains, and quick-release clip.
The warranty also excludes the equipment on which the serial number was erased or made illegible, on which unauthorized people made attempts of repair, which were totally or partially dismantled.

Our equipment is covered by a manufacturer’s warranty (parts and labor) of 12 months following the purchase date by the final customer, without exceeding 24 months from the date of purchase by the client. The final user can extend this manufacturer’s warranty for a further 12 months by filling in the warranty extension form on our website  www.euromair.com (under After-Sale Service) within 4 weeks of purchase.
This manufacturer’s warranty and its extension shall automatically cease if the customer does not resell the equipment within 24 months of its purchase. The cases of exclusion of warranty mentioned in the articles above are also applicable to our own equipment.
The manufacturer’s warranty shall always be subject to the presentation of the purchase invoice.
If the defective equipment is covered by the manufacturer’s warranty, it shall be repaired or replaced at our discretion free of charge.
If the defective equipment is not covered by the manufacturer’s warranty, we shall issue a quote for the repair that we shall submit to the customer for approval.
Except as otherwise required by law, this manufacturer’s warranty is exclusive of all other warranties, including the statutory warranty of hidden defects.
In case of intervention of our services on a breakdown caused by the customer or an incident excluded in the conditions referred to above, the costs of repair and transport shall be invoiced to the customer.
We exclude all liability for indirect damages suffered by the customer, such as, but not limited to, loss of income, turnover, loss of profits, loss of image, of any kind whatever.

In all cases, our liability shall be limited to the amount paid by the customer for non-compliant equipment.
Any legal action of the customer against us relating to the warranty of the equipment shall be barred 1 year after the date of discovery of the defect. The customer shall have to  prove the date of this discovery.
Request for Warranty
For any request related to the repair of equipment covered by the manufacturer’s warranty, the customer shall have to fill the warranty form, available on our website, under  After-Sale Service.
For a full dossier, the following documents shall have to be attached:

• the purchase invoice of the final user
• pictures of the defective parts of the equipment
• a description of the breakdown
• the quote of labor if the customer is certified by EUROMAIR for repairing the equipment

No invoice of labor shall be taken into account without our prior approval.
Analysis of the breakdown by our technical department
A file number shall be given to the customer and an answer shall be provided within 48 working hours after the reception, provided that the request for warranty is considered as full.
In the event the equipment is covered by the manufacturer’s warranty, we shall confirm the warranty to the customer and send him a quote (without price) detailing the parts to be changed and any comments.

Return of replacement parts
Replacement parts must be ordered with a warranty agreement number and will be made available to the customer at our factory.
The conditions of return of the equipment are detailed in our Delivery terms.
In the case of a warranty claim on an on-board component such as a Kohler, Honda or Vanguard engine in a machine manufactured by us, only the manufacturer of the component is able to validate the warranty coverage.
In this case, the request must be addressed directly to the manufacturer of the component or to its nearest authorized representative. The Euromair, Euromair MPC or Mixer service centers may be considered as the manufacturer’s representatives if they are the closest. As this principle also applies to batteries, our supplier Parts Holding Europe, or one of its sister companies, remains your contact for your requests (https://www.partsholdingeurope.com/).

EUROPE PROJECTION – 228, avenue Olivier Perroy 13790
ROUSSET – Tél : +33 (0)4 42 29 08 96
– Fax : +33 (0)4 42 53 44 36
SAS au capital de 400 000 €
– RCS Aix-en-Provence B 394 961 510
– NAF 2892 Z
– Intracom : FR 54 394 961 510
More information onwww.euromair.com

References

• Parts Holding Europe - Leader de la distribution de pièces auto
• Euromair | Fabricant de machines à projeter et pulvériser

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>