Voweek VW-VC07 Cordless Stick Vacuum Cleaner Instruction Manual
- June 5, 2024
- Voweek
Table of Contents
VACUUM CLEANER
INSTRUCTION MANUAL
Model: VW-VC07
For any questions and malfunctions of the appliance during use, please contact our customer service email: support@voweek.com
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
When using electric appliances, basic precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE)
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, DAMAGE, OR INJURY:
-
To protect against electrical shock, do not immerse the power cord or plug in water or any other liquid. To avoid the risk of electrical shock or serious personal injury, always operate with dry hands.
-
Close supervision is necessary when any appliance is being used by or near children. This vacuum is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the vacuum by a person responsible for their safety.
-
Do not use the vacuum outdoors. It is for household use only.
-
Do not use the vacuum if it has been dropped, damaged, left outdoors, or dropped in water. Please contact customer service for help when the appliance or the adapter is damaged.
-
Use the vacuum only as described in this manual. The use of accessory attachments not recommended may cause damage to the vacuum or personal injuries.
-
Do not use abrasive materials to clean the vacuum. Do not use spirits or other solvents to clean the appliance.
-
Do not use the appliance to vacuum all the below things:
● Water, flammable or combustible liquids such as gasoline;
● Lighted stub, matches, hot ashes, and other combustible things;
● Needles, pins, and other sharp things;
● Wood pieces, gesso, cement, calcimine, and other tiny granules;
● Pieces of string or fabrics. -
Do not pick up liquids with the vacuum or use them on wet floors. Do not immerse the vacuum in water.
-
Do not use the vacuum on concrete, tar, or similar rough surfaces.
-
Do not vacuum frayed carpets or tassels on carpets.
-
Do not use the vacuum without the dust cup in place.
-
Do not put any object into the openings of the vacuum. Do not use it when any opening is blocked. Keep free of dust, lint, hair, and anything that may reduce airflow.
-
Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts.
-
Store the vacuum indoors. Store after use to prevent accidents.
-
Keep the vacuum cleaner away from stoves and heat-emitting appliances. Heat can deform and discolor the plastic parts of the unit. Please use the vacuum in a 0 to 40 degrees temperature environment.
-
Always remove the adapter from the power socket when the appliance is not in charge.
-
Unplug the charging cord from the appliance and power it off before cleaning or performing maintenance, making tool adjustments, changing accessories or storing to avoid powering it accidentally.
-
The battery must be removed from the appliance before it is scrapped.
-
The battery has to be disposed of safely.
-
The appliance includes Li-ion batteries, do not incinerate the batteries or expose to high temperatures, as they may explode.
-
The thermal cutout will switch off the vacuum automatically when it overheats. If this should happen, turn off the power switch, and wait for 45 minutes to restart the vacuum.
-
Only the adapter provided by the manufacturer can be used.
Please keep the adapter
away from liquids.| Do not vacuum large
piece of paper.| Do not vacuum fire or
flammable substances.| Do not vacuum water
or liquids.| Do not remove plug
by grasping the cord.
WHAT’S IN THE BOX
CAUTION: Assemble the vacuum according to chapter “Assembly”.
Vacuum main body| Extension tube| Floor brush
2-in-1 brush| Wall hanger| Screws and wall anchors
Cleaning brush| Adapter| HEPA filter
OVERVIEW
ASSEMBLY
SPECIFICATION
Name | VACUUM CLEANER |
---|---|
Model | VW-VC07 |
Adapter Input Voltage | 100~240 V 50/60 Hz |
Adapter Output Voltage | 26 V |
OPERATING INSTRUCTIONS
Charging Instruction
CAUTION:
It is important to fully charge your machine before using for the first time
and after every use. The flashing indicator light shows the battery power is
low. Please charge the vacuum when the last light flashes.
Charge with the vacuum main body
Plug the adapter into a wall outlet and charging head into the vacuum for
charging. The battery indicator will be in a cycle of illuminating while the
vacuum gets charged. When the vacuum is fully charged, all battery indicators
will be solid on. When the vacuum is fully charged, all battery indicators
will be solid on.
Charge the battery pack alone
Press the release button at the side of the battery pack.| Hold the button and
pull it out to detach.
---|---
3 Plug the adapter into wall outlet and charging head into the battery pack for charging the it.
2-in-1 Brush Instruction
Press the conversion button to pull the bristle back to use as a crevice
tool.| Hold and push out the bristle rectangle to use as a brush.
---|---
Wall Hanger Instruction
Use the screws and wall anchors to fix the wall hanger at a certain height to mount the vacuum with a tube attached. After fixing the wall hanger, store the vacuum on it when not in use.
CLEANING AND MAINTENANCE
CAUTION:
Always be sure that the vacuum is switched to OFF before attempting to empty
the dust cup.
Dust Cup and HEPA Filter Cleaning
Empty the dust cup when the dust inside is paralleled with the lower rim of the filter case. Otherwise, the suction may be weakened.
Remove the extension tube from the main body before maintaining and cleaning
dust cup and HEPA filter.
Open the dust cup lid to dump dust.| Hold and turn the filter case clockwise
to detach it.
---|---
Pull up the HEPA filter out of the mesh shell.| Brush the HEPA filter with a
cleaning brush before rinsing it.
---|---
Rinse both the HEPA filter and the mesh shell under tap water.| Air dry them
for at least 24 hours. Do not assemble it back until completely dry.
---|---
Assemble the mesh shell and the HEPA filter back in place. Do not assemble them until completely dry.
CAUTION:
The filter is suggested to be washed (air dry before installing back) every 2
weeks, to be replaced every 2 months, otherwise, it will result in an
insufficient filter system and loss of suction.
Floor Brush Cleaning
CAUTION:
When the floor brush stops spinning suddenly and all the floor brush block
indicators get flashing, there may be clogs on the roller brush. Please check
and clear clogs on the roller brush.
Press the release button and hold to pull out to detach the tube from floor
brush.
Push the release switch toward the ” ” icon at the side of the floor brush to
detach the buckle.
Grab the roller brush head and remove it from the floor brush.| Use a cleaning
brush to remove hair and strings entangled on the roller brush.
---|---
Check the roller brush and make sure the round side of it attaches to the
plastic axle first when assembling it back.| On the other side of the roller
brush, please make sure the arc-shaped part of it is downward when assembling
it back.
---|---
Insert the buckle back to place as the picture shows.| A “click” will be heard
if the buckle is inserted in place.
---|---
CLEAR A CLOG
CAUTION:
Low suction or vacuum stopped caused by overheating may be due to a clog in
the vacuum. Please check and clear clogs in the dust cup, HEPA filter,
extension tube, and floor brush.
Check and empty the dust cup.| Check and rinse the HEPA filter. Do not
assemble them until completely dry.
Check if there are any clogs inside the extension tube.| Check the floor brush and clear the clog on the roller brush with the blade.
TROUBLESHOOTING
PROBLEM | POSSIBLE REASONS | SOLUTIONS |
---|---|---|
The vacuum can not be charged | The used adapter is not the original one |
Please charge the vacuum with the original adapter
The battery pack/adapter malfunctions| Please contact the customer service for
help
The vacuum can not be powered on| The battery runs out| Please charge the
vacuum with the original adapter
The battery pack is not attached correctly| Remove and attach back the battery
pack and make sure it is attached in place
Other malfunctions| Please contact the customer service for help
The vacuum stops
working
suddenly| The battery runs out| Use the original adapter for charging. It is
recommended to charge the vacuum after each time use and use the low suction
mode for long runtime
The floor brush gets stuck| Clean foreign objects entangled on the floor brush
1. The air duct is blocked
2. The dust cup is full| Clean the floor brush, extension tube, dust cup, and
the HEPA filter regularly
Other malfunctions| Please contact the customer service for help
The cleaning results are
not good| Incorrect use of the vacuum| 1. It is recommended to use high
suction mode for cleaning complicated environments
2. It is recommended to use the crevice tool for better pickup for vacuuming
heavy objects such as beans
3. It is recommended to use the floor brush for cleaning stain
The battery runs out| Please charge the vacuum fully and try to turn it on
again
1. The air duct is blocked
2. The dust cup is full| Clean the floor brush and extension tube. dust cup
and the HEPA filter regularly
The HEPA filter is not dried completely| Detach and air dry the HEPA liter
completely. It is recommended to the dean and replace it regularly
There is static during vacuum working| There is too much dust inside the dust
cup| Please empty the dust cup
The vacuum runs at an environment full of static| Its normal that there may be
much static in the air in winter and dry regions
The electric
floor brush
stops working| The floor brush gets stuck| Clean foreign objects entangled on
the floor brush
Other malfunctions| Please contact the customer service for help
WARRANTY
CUSTOMER CARE
The 1-year Limited Warranty is valid for products purchased from our Voweek
only, starting from the date of the original retail purchase. We will provide
customer service for any defects in quality or materials under normal, non-
commercial use.
- According to the requirements outlined in this instruction manual, the warranty is subject to the following conditions and exclusions.
- This warranty provides, at no extra cost to you all labor and parts necessary to ensure your machine is in proper operating condition during the warranty period.
- We provide the repair or replacement of your Voweek appliance if your Voweek appliance is found to be defective due to faulty materials, or workmanship function within 1 year of purchase or delivery. ( If any part is no longer available or out of manufacture, we will replace it with a functional replacement part).
WHAT IS NOT COVERED
- Under your Voweek guarantee, Voweek shall not be liable for costs of repair or replacement of a product incurred as a result of Accidental damage, faults caused by negligent use or care, misuse, neglect, careless operation or handling of the Voweek appliance which is not in accordance with this Voweek Instruction Manual.
- Machines purchased from an unauthorized dealer.
- Use of parts and accessories other than those produced or recommended by Vorwerk.
- Repairs or alterations carried out by unauthorized parties or agents.
- Use of the machine other than for normal domestic purposes, e.g. for commercial or rental purposes.
- Reduction in battery run time due to battery age or use.
WARRANTY SERVICE
- If you have a query about your Voweek appliance, please contact the Voweek customer service email: support@voweek.com
- Please inform us your model name/number, purchase date, order number, machine problem and your requirement.
- Your model number can be found on rating plate.
- Please keep your purchase receipt in a safe place to ensure you have this information. Service under this warranty will not extend the available time of warranty.
Manufacturer: Shenzhen Yibai Net w ork Technology Co., Lt d
Address: Bldg 1-101, TOD Tech Center, Lipu Rd 7,
Dafapu Community, Bantian St.Longgang Dist.,
Shenzhen, China
Email: support@voweek.com
This device complies with Part 15 of the FCC Rules:
Operation is subject to the following two conditions:
1)This device may not cause harmful interference, and
2)This device must accept any interference received, including interference
that may cause undesired operation