Perel ED88 WIRELESS DOORBELL User Manual
- June 5, 2024
- PEREL
Table of Contents
Perel ED88 WIRELESS DOORBELL
Introduction
To all residents of the European Union Important environmental information about this product This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules. If in doubt, contact your local waste disposal authorities. Thank you for choosing Perel! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, do not install or use it and contact your dealer.
Safety Instructions
Keep this device away from children and unauthorized users. Indoor use only. Keep this device away from rain, moisture, splashing and dripping liquids.
General Guidelines
Refer to the Velleman® Service and Quality Warranty on the last pages of this manual. Keep this device away from dust and extreme temperatures. Protect this device from shocks and abuse. Avoid brute force when operating the device.
- Familiarise yourself with the functions of the device before actually using it.
- All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the device is not covered by the warranty.
- Only use the device for its intended purpose. Using the device in an unauthorised way will void the warranty.
- Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
- Due to constant product improvements, the actual product appearance might differ from the shown images.
- Product images are for illustrative purposes only.
- Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device against damage by leaving it switched off until it has reached room temperature.
- Keep this manual for future reference.
Features
- easy installation via auto-learning code button
- 36 melodies and adjustable volume (high – medium – low)
- kit includes 1 receiver + 1 transmitter, supports up to 4 transmitters (order code EDB8/TX)
- receiver: for indoor use
Overview
Refer to the illustrations on page 2 of this manual.
Battery
Warning: Do not puncture batteries or throw them in fire as they may explode. Do not attempt to recharge non-rechargeable batteries (alkaline). Dispose of batteries in accordance with local regulations. Keep batteries away from children.
Transmitter
- Open the transmitter using a flat-head screwdriver: carefully push the clips at the bottom and twist very slightly.
- Install the included CR2032 lithium battery in accordance with the polarity markings inside the battery compartment. Close the housing.
Receiver
- Remove the battery cover.
- Install two 1.5 V AA batteries in accordance with the polarity markings inside the battery compartment.
- Close the housing.
Installation Preliminary Remarks
- Install the receiver and transmitter within their operating distance.
- Do not install the receiver and transmitter onto or near uPVC or metal objects, near heat sources or in damp areas.
Transmitter
- Drill two holes with a diameter of 6 mm (distance 36 mm) at the required height. Insert a nylon plug into each hole.
- Punch the two holes in the back cover.
- Fix the back cover onto the wall and click the front cover onto the back cover.
- You can also stick the transmitter onto the wall with double-sided tape.
Receiver
- Drill two holes with a diameter of 6 mm (distance 56 mm) at the required height. Insert a nylon plug into each hole.
- Insert a screw into each hole. Do not fully insert them but leave about 5 mm free.
- Hang the receiver onto the screws.
Operation
- Press the auto-learning button on the back of the receiver.
- Press the push button on the transmitter once. The receiver will sound to indicate that the new operation code has been registered.
- Operate in the same way to memorize an extra transmitter.
- Press the melody button to select one of the 36 melody. Press the volume button to select the high, medium or low ring volume.
Remark
If the receiver sounds for no reason during the learning procedure, the signal
may be subject to interference. Reset the code as described above.
Cleaning and Maintenance
This device does not need any particular maintenance. Occasionally wipe it with a damp cloth. Do not use harsh chemicals, cleaning solvents or strong detergents.
Technical Specifications
- operating distance……………………… ± 100 m (in open field)
- frequency………………………………………………. 433.92 MHz
- ringing volume …………………………. > 80 dB (within 0.5 m)
- transmitting power ………………………………………. 0.12 mW
- digital code ………………………………………….. auto-learning
- modulation type ………………………………………………… ASK
- dimensions
- receiver (H x W x D)……………………. 105 x 105 x 30 mm
- transmitter (H x W x D) ………………….. 50 x 50 x 20 mm
- power supply
- receiver ……………….. 3 V (2 x 1.5 V AA/LR6, not incl.)
- transmitter …………. 1 x 3 V CR2032 lithium battery (incl.)
- options
- CR2032 lithium battery ……………………………… CR2032C
- AA/LR6 alkaline battery …………………………………. LR6C
Use this device with original accessories only. Velleman nv cannot be held responsible in the event of damage or injury resulting from (incorrect) use of this device. For more info concerning this product and the latest version of this manual, please visit our website www.velleman.eu. The information in this manual is subject to change without prior notice.
RED Declaration of Conformity
Hereby, Velleman NV declares that the radio equipment type EDB8 is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address:
www.velleman.eu.
References
- Details – Own brands – Velleman – Wholesaler and developer of electronics
- Velleman – Wholesaler and developer of electronics