eSSL FL-300 Intelligent Fingerprint Door Locks User Manual

Table of Contents

eSSL-FL-300-Intelligent-Fingerprint-Door-Locks-
FIG-1

eSSL-FL-300-Intelligent-Fingerprint-Door-Locks-
FIG-2

Please keep the internal/external panels clean before installation.

Adjust handle ball according to door open way.
Lock body installation: Put the lock body into the guard hole and the lock body cable should go through the spindle hole to inside door and last tighten the screw.
Put stud onto front panel connection screw and put spring into spindle hole.
Put spindle into lock body(follow drawing), take data line from above lock body into the inside door, spindle and stud should be in the corresponding hole, front panel should be compactly installed on the door.
Connect the mainboard cable to the corresponding interface of the back pane make sure the spindle, and handle ball core into the corresponding position, and tighten back panel onto the door and tight panel installation screw.
Adjust inside and outside panel verticality and tight screw put plugin.
The install battery cover, try opening by fingerprint, RFID card or pin code or manual key.

Multiple-way to access: Fingerprint, Pin Code, RFID Card, & Mechanical Key.
Fingerprint: Advanced semiconductor sensors with 360° scanner.
Pin code Elegant keypad with code scrambling feature. Before correct password can input 12 digital which can avoid password peeping.
Dual authentication mode: Fingerprint mode ( master + common user ), fingerprint + pin code, fingerprint + RFID card mode, A fter this setting dual authentication will be required to access the lock at same time to open the door, suitable for special occasions.
Lock can have multiple access users capacity: Fingerprint ( 5 Master Users & 85 Normal Users ), Pin-code ( 5 Master Users & 15 Normal Users ), RFID cards (99 Normal Users)
Alarm: Tamper, low battery alarm and password protection.
External power supply: Can use power bank with 5V for emergency power supply

After installation of lock please reset lock to factory default mode.
After factory default mode make sure to register 1 master user.
The handle is the key part for opening and closing door, and its flexibility ratio directly influences the usage of door lock, hence, don’t hang articles on the handle.
Gently press fingerprint on the fingerprint sensor for registration of fingerprint. Please don’t press with great force to prevent scratching the fingerprint sensor.
This lock uses 4 AA high-energy alkaline batteries (1.5V). When it prompts” the voltage is low, please replace battery” for the first time, the door can e opened for about 100 times as per different battery capacities; At this time, the battery should be replaced promptly to avoid inconvenience due to the exhausted battery.

Reset factory default: Press RESET at the back of the lock for 5 seconds, voice will prompt reset succeed.
Register master/user:
- Initial mode: Touch screen keypad for lights on and press # for 2 seconds and voice prompt additions of master code.
Once the master user is added:
- Add new master: Touch the screen for lights on and press # for 2 seconds, voice prompts confirm master, input any registered master, and press # again to add the master user (fingerprint /password)
- Add new common user: Touch screen for lights on and press # for 2 seconds input any registered master user “and” voice prompt “add user” to add a new fingerprint, password, and card, etc.
Addition of “One Time password or Guest password”: Users can be added with password access which will provide access one time and will expire after its used

Remark

All fingerprints need to scan 3 times for addition.
Password is 8 digits and has to be entered 2 times for addition.
The card is registered after voice prompts “add user” & scan the card near the RFID scanner for confirmation.
After successful registration press * to exit.

Delete registered fingerprint/card/password:

Deleting individual fingerprint: Touch screen for lights on & long press 1 for 2 seconds. After the voice prompts input fingerprint to delete, press fingerprint on the scanner to delete.
Deleting by user numbers: Touch screen for lights on & long press 1 for 2 seconds. After voice prompts input the fingerprint code to delete
enter the user number of the fingerprint to delete.
Delete all cards: Touch screen for lights on & long press 2 for 2
seconds press # to enter in to delete all cards option and # again to
confirm deletion.
Delete the corresponding password: Touch the screen for lights on & long press 4 for 2 seconds at this time input the password code and press # to confirm.
Delete all passwords: Touch screen for lights on & long press 4 for 2 seconds press # to delete all passwords.

Remark

When Deleting a fingerprint, one master user in fingerprint has to be left.

Checking lock information

Touch screen for lights on 2 long press 0 for 2 seconds:
Press 1 To open with any registered user.
Press 2 For dual authentication with a fingerprint.
Press 3 For fingerprint + password opening.
Press 4 For fingerprint + card opening.
Press 5 To get the lock storage status: Number of master users, number of normal users, for fingerprint, RFID & Pin code access.
Press 6 To get the lock series information: XXXXXXXX
Press 7 For the rest factory default and # to confirm.