DYNOJET PC6-26003 Power Commander 6 Installation Guide
- June 3, 2024
- Dynojet
Table of Contents
POWER COMMANDER 6
Installation Guide for PC6-26003
Model Coverage: 2009-2017 Moto Guzzi Griso 1200
PARTS LIST
| 1 POWER COMMANDER 6 | 2 POWER COMMANDER DECALS |
|---|---|
| 1 INSTALLATION GUIDE | 2 VELCRO STRIPS |
| 1 USB CABLE | 1 ALCOHOL SWAB |
| 2 DYNOJET DECALS | 1 POSI-TAP |
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION. THE IGNITION MUST
BE TURNED OFF BEFORE INSTALLATION.
IPC6-26003.01
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map
(Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You can
switch on the fl y between these two base maps when you hook up a switch to the
MAP inputs. You can use any open/close type switch. The polarity of the wires
is not important.
Shifter
(Input 1 or 2) Used for clutch-less full-throttle upshifts. Insert the wires
from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of
the wires is not important. Set to Input 2 by default.
Speed
If your application has a speed sensor then you can tap into the signal side
of the sensor and run a wire into this input. This will allow you to calculate
gear position in the Control Center Software. Once gear position is setup you
can alter your map based on gear position and setup gear-dependent kill times
when using a quick shifter.
Analog
This input is for a 0-5v signal such as engine temp, boost, etc. Once this
input is established you can alter your fuel curve based on this input in the
Power Core software.
Launch
You can connect a wire to either Input 1 or Input 2 and then the other end to
a switch. This switch when engaged (continuity) will only allow the RPM to be
raised to a certain limit (set in the software). When released, you will have
full RPM.
WIRE CONNECTIONS
To input wires into the PC6 fi rst remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tightens the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
2 2009-2017 MOTO GUZZI GRISO 1200
INSTALLING THE POWER COMMANDER 6
-
Remove the seat.
-
Remove the fuel tank side covers.
-
Secure the PC6 module to the left side of the fuel tank with the supplied Velcro.
Clean both surfaces with the supplied alcohol swab prior to applying the Velcro adhesive. -
Attach the PC6 ground wire with the small ring lug to the valve cover bolt shown.
-
Unplug the stock wiring harness from the fuel injector on the LEFT cylinder head.
-
Plug the pair of PC6 leads with ORANGE colored wires in-line of the LEFT cylinder fuel injector and the stock wiring harness.
-
Unplug the stock wiring harness from the injector.
-
Unplug the stock wiring harness from the Throttle Position Sensor.
-
Using the supplied Posi- tap, attach the GREY wire of the PC6 to the stock and The RED wire of the TPS wiring harness.
This is position “C” on the stock TPS connector. -
Plug the stock TPS connector back into the TPS.
-
Plug the pair of PC6 leads with YELLOW colored wires in-line with the RIGHT cylinder fuel injector and the stock wiring harness.
-
Reinstall the seat and side covers.
Download the latest map fi les from our website at dynojet.com/tunes.
2191 MENDENHALL DRIVE, NORTH LAS VEGAS,
NV 89081 – 800-992-4993
DYNOJET.COM
© 2009-2021 DYNOJET RESEARCH ALL RIGHTS RESERVED
PC6-26003
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>