ADLER AD 9608 Lint remover User Manual

: June 5, 2024
: ADLER

Table of Contents

DESCRIPTION OF THE DEVICE
CHARGING THE SHAVER
USING CLOTHES SHAVER
CLEANING OF CLOTHES SHAVER
TECHNICAL DATA
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AD 9608
user manual

GENERAL SAFETY CONDITIONS
IMPORTANT SAFETY INSTRUCTIONS FOR CAREFULLY READ CAREFULLY AND
KEEP FOR FUTURE REFERENCE

Read the operating manual before using the device and follow the instructions contained in it. The manufacturer is not liable for damage caused by using the device against its intended use or improper handling.
The device is for domestic use only. Do not use for other purposes that are not in accordance with its intended use.
The device should be connected only to a socket with 220-240V ~50/60Hz ground. In order to increase the safety of use, do not switch on many electrical devices simultaneously to one circuit.
Be extra cautious when using the device when children are nearby. Do not allow children to play with the device, do not let children or persons not familiar with the device use it.
WARNING: This equipment may be used by children over 8 years of age and persons with limited physical, sensory or mental abilities, or persons who have no experience or knowledge of the equipment, if this is done under the supervision of a person responsible for their safety or given to them. tips on the safe use of the device and are aware of the dangers associated with its use. Children should not play with the equipment. Cleaning and maintenance of the device should not be performed by children unless they are over 8 years of age and are supervised.
Always after use, remove the plug from the socket by holding the socket with your hand. DO NOT pull on the power cord.
Do not immerse the cable, plug and the entire device in water or other liquid. Do not expose the device to atmospheric conditions (rain, sun, etc.) or use in conditions of high humidity (bathrooms, damp camping houses).
Periodically check the condition of the power cord. If the power cord is damaged, it should be replaced by a specialist repair facility in order to avoid a hazard.
Do not use the device with a damaged power cord or if it has been dropped or damaged in any other way or not working properly. Do not repair the device yourself, as it may cause shock. Please return the defective device to the appropriate service center for inspection or repair. All repairs may only be carried out by authorized service points. Incorrectly performed repair can cause serious danger to the user.
The power cord can not hang over the edge of the table or touch hot surfaces.
Before cleaning or after use, remove the plug from the socket by holding the socket with your hand. DO NOT pull on the power cord.
To provide additional protection, it is advisable to install a residual current device (RCD) with a rated residual current not exceeding 30 mA in the electrical circuit. In this regard, please contact an electrician.
Do not allow the device or adapter to get wet. If the device falls into the water, immediately pull the plug or adapter from the power socket. Do not put your hands into water when the device is connected to the mains. Before re-use, it must be checked by a qualified electrician.
Do not handle the device or adapter with wet hands.
The device should be turned off every time you put it down.
Do not leave the device or adapter connected to the outlet unattended.
Do not use the device near water, eg in the shower, in the bathtub or above the washbasin with water.
ATTENTION! The blades are very sharp!
Exercise caution when opening the bin to not damage it.
Do not bend or deform perforated blade protector.
Exercise extreme caution when pulling out blades.
Wipe the shaver body with dry cloth.
The lint bin should be emptied when it is 3/4 full.
Deposit on the inner and outer surface of cutting film decreases the shaving efficiency. Clean the film regularly with a brush.
Flatten the fabric surface before using the shaver.
Do not press the shaver in the clothing, as this may damage the fabric.
Do not use the shaver on the clothes that you are wearing, always remove them before using the shaver. Otherwise the body or shaver damage may occur.
Always switch the shaver off before plugging in the power adaptor.
The shaver is equipped with a safety lock. The shaver cannot be turned on, if the film is installed improperly or is not properly tightened.
Make sure not to use shaver on buttons, zippers, applications, stripes, stickers, labels, abrasions, seams or fasteners.
Do not use shaver to remove lint from the silk fabrics. This can damage the fabric as well as the shaver blades.

DESCRIPTION OF THE DEVICE

1. Safety cap
3. Blade protector
5. Rotary shaft
7. Shaver body
9. Power LED
11. Brush| 2. Removable ring
4. Blade assembly
6. Power switch
8. Lint and pillings bin
10. Power socket
---|---

CHARGING THE SHAVER

Make sure the shaver is switched off.
Connect the power cable to the shaver’s power socket.
Connect power plug to the 220-240V ~50/60Hz electric socket.
Maximum charging time for completely discharged battery is 8 hours.
Battery lifetime will be longer, if the battery is charged only after it is completely discharged.

USING CLOTHES SHAVER

Clothes shaver is battery and mains powered. It can be powered from internal battery or directly from mains.

Turn the shaver on.
Place the clothes (fabric) on flat surface, smoothen the creasings and move the shaver forth and back along the fabric.
Resisting lint can be removed by moving shaver crosswise and then lengthwise (in cross-pattern) on one, small fragment of clothes.
In case of clothing with pattern, move the shaver along the pattern line.

CLEANING OF CLOTHES SHAVER

Turn the shaver off.
Remove the blade protector (3).
Remove blades (4) (be careful! the blades are very sharp).
Using the provided brush clean the blade protector (3), blades (4) and rotary shaft (5).
Empty the lint and pillings bin (8).
Assemble all removed parts in reverse order.

TECHNICAL DATA

Power supply: 220-240V ~50/60Hz
Power:5W

Please transfer cardboard packaging to waste paper. Pour the polyethylene bags (PE) into the plastic container Worn device should be returned to the appropriate point storage because it is dangerous in the device ingredients may pose a threat to the environment. The electrical device should be handed over to limit its reuse and use. If in the device there are batteries you have to take out and give to the point stored separately.

WWW.ADLEREUROPE.EU