VOLLRATH T38707 One Piece Cafeteria Breath Guard Installation Guide

: June 7, 2024
: VOLLRATH

Table of Contents

T38707 One Piece Cafeteria Breath Guard
Specifications:
Product Usage Instructions:
One Piece Breath Guard Installation:
Three Piece Breath Guard Installation:
- FAQ:
Q: What should I do if I accidentally overtighten the cap
Q: Can I disassemble the breath guard for cleaning?

T38707 One Piece Cafeteria Breath Guard

“`html

Specifications:

Product Name: Cafeteria Breath Guard
Types: One Piece, Three Piece
Item No.: 2350030-01 Rev 04/12

Product Usage Instructions:

One Piece Breath Guard Installation:

Install the breath guard uprights (A) to the studs (B) securing
with cap nuts (C) as shown in Figure 1. Repeat for all four
uprights.

Three Piece Breath Guard Installation:

Install the breath guard uprights (A) to the studs (B) securing
with cap nuts (C) as shown in Figures 1 and 2. Repeat for all four
uprights.
Install the breath guard support tube (D) between the uprights
(A) securing with cap nuts (C) as shown. Repeat on the other
side.
Install the side breath guards (E) securing with screws (F) and
cap nuts (C) as shown. Repeat for all mounting locations.
Install the side shield (G) to the support tube (D) securing
with cap nuts (C) as shown. Repeat on the other side.
Install the support bar and stud assembly (H) to the side
breath guards (E). Repeat for all mounting locations.
Install the top breath guard (I) to the support bar and stud
assembly (H) securing with cap nuts (C). Repeat for all mounting
locations.

FAQ:

Q: What should I do if I accidentally overtighten the cap

nuts?

A: If you accidentally overtighten the cap nuts
and notice cracking in the plastic, stop immediately and contact
customer service for assistance. Continuing to tighten may cause
further damage to the product.

Q: Can I disassemble the breath guard for cleaning?

A: Yes, you can disassemble the breath guard
for cleaning purposes. Follow the installation steps in reverse to
disassemble, clean the components, and then reassemble following
the installation instructions.

“`

Installation Instructions

One Piece cafeteria Breath Guard three Piece cafeteria Breath Guard

These instructions cover the installation of the one pice Cafeteria Breath Guard and the three piece Cafeteria Breath Guard.
One Piece Breath Guard installatiOn
Some units are shipped with a breath guard not installed. To install the breath guard follow these steps: NOTE: Use caution when tightening the cap nuts. Overtightening may cause the plastic to crack. 1. Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C)
as shown. See Figure 1. Repeat for all four uprights.

three Piece Breath Guard installatiOn
Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:
NOTE: Use caution when tightening the cap nuts. Overtightening may cause the plastic to crack.
1. Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights.

c

i

a c
f e
c

h c e
G

e
a c e
f

a

B

c

B G

c

Bd

c

a

Figure 1. One Piece Breath Guard Installation

2. Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
3. Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
4. Install the side breath protector (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.

a c

c

a

B

G

c

B

c

Bd

Figure 2. Three Piece Breath Guard Installation
2. Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
3. Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
4. Install the side shield (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
5. Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
6. Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
Item No. 2350030-01 Rev 04/12

www.vollrathco.com

The Vollrath Company, L.L.C. 1236 North 18th Street Sheboygan, WI 53081-3201 U.S.A. Main Tel: 800.628.0830 Service Tel: 800.628.0832 FAX: 800.752.5620

Vollrath of Canada, Co. Tel: 800.695.8560 FAX: 800.752.5620
© 2010 The Vollrath Company, L.L.C.