Humanscale NeatHub charging options with four power ports Plug User Guide
- June 5, 2024
- Humanscale
Table of Contents
Humanscale NeatHub charging options with four power ports Plug
STEPS
- Slide the NeatHub unit onto a desk surface edge. Tighten the clamp by twisting the knob until it is secure.
- Connect the plug to a grounded outlet.
CLEANING GUIDELINES
- Always unplug before cleaning.
- Stay clear of electrical sockets and ports.
- Do not use harsh chemicals or solvents.
INSTALLATION GUIDELINES
This product is intended to be used on a desk work surface
CAUTION:
- DO NOT plug into an extension cord.
- DO NOT plug in extension cords to the outlets on the NeatHub.
Connect Your Equipment:
Plug your equipment’s power cords (including 2-wire devices) into the
NeatHub’s AC outlets. DO NOT plug in extension cords, other NeatHub products,
power strips, or height-adjustable tables. DO NOT OVERLOAD the NeatHub’s
outlets. NeatHub can accommodate a total equipment load of up to 12 amps
(whether plugged into a single outlet or spread out over multiple outlets).
Connect Your NeatHub:
Plug the NeatHub plug into a standard 3-wire grounded 120V AC outlet. This
product is for use on a nominal 120-volt circuit and has a grounding plug that
looks like the plug illustrated in Step 2 of the installation. Make sure that
the product is connected to an outlet having the same configuration as the
plug. No adapter should be used with this product. Do NOT plug into a 2-wire
outlet.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
CAUTION: Read all instructions prior to installation. This product is
designed for indoor use only. Install the product away from heat-emitting
appliances such as radiators or heat registers.
- DO NOT install where excessive moisture is present.
- DO NOT connect to an ungrounded outlet.
- DO NOT connect product to an extension cord or adapter.
- DO NOT plug in extension cords, other NeatHub products, electrical height adjustable tables, or any type of power strip.
- DO NOT install electrical wiring during a lightning storm.
- DO NOT drill into any part of the housing or open the housing for any reason. There are no user-serviceable parts inside.
WARNING: Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended.
BEFORE USE
- Product is to be used indoors only.
- Inspect thoroughly before installation and use. DO NOT USE IF DAMAGED.
- Do not run cord through doorways or holes in ceilings/walls/floors.
- FULLY INSERT plug into outlet.
- Do not remove, bend or modify metal prongs or pins of cord.
- Do not use excessive force to make connections.
DURING USE
- Keep away from water.
- DO NOT USE WHEN WET.
- Keep children and pets away from product.
- AVOID OVERHEATING. Uncoil cord and do not cover it with any material.
- Do not drive, drag or place objects over cord.
- Do not walk on cord.
- Do not plug an extension cord or power strip into product.
- Do not plug product into an extension cord or adapter.
- Do not plug one NeatHub product into another.
- Do not plug an electrical table into product.
- Do not put any metal objects in outlet to avoid getting shocked/hurt.
AFTER USE
- GRASP PLUG to remove from outlet. Do not unplug by pulling on cord.
- Always store product INDOORS.
ELECTRICAL SPECIFICATIONS
PART # PWR-2A1U1C-S.PLUG
PART # PWR-2A1U1C-S.PLUG
Ports| AC Outlets| 2x NEMA 5-15R
USB Ports| 1x USB-A, 1x USB-C
Cord| Length| 5’8” (172.7cm)
Electrical Rating
| Input Voltage| 120VAC, 60Hz, (12A max)
USB Ports
| (Connected to one of the two ports) USB-A 5V 3A (15W max)
USB-C 20V/1.25A; 15V/1.4A;
9V/2.2A; 5V/3A (25W max)
(Both ports connected) USB-A 5V/2A (10W max) USB-C 5V/2A (10W max)
Environmental
| Temperature – Operating| 0°C to 30°C
Temperature – Storage| -10°C to 50°C
Regulatory Compliance| Safety| UL962A, CSA C22.2 No.308
EMC| FCC Part15 Subpart B Class B
CAN ICES-003 (B)/NMB-3 (B)
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
MECHANICAL SPECIFICATIONS
Size
| Width| 5.6in (142mm)
---|---|---
Depth| 4.2in (107mm)
Height| 3.6in (91mm) from work surface
Clamp Screw Range| 1.25in (32mm)
Work surface thickness range 0.5in – 1.125in