BluMill MT-710 Robot Vacuum Cleaner Instruction Manual

: June 5, 2024
: bluMill

BluMill MT-710 Robot Vacuum Cleaner

Safety Regulations

**| Please read the manual carefully before using the product and keep this instruction for reference,**
---|---

Please read the manual carefully before using the product and keep these instructions for reference.
This product cannot be used by children under 8 years of age or people with mental disabilities. If you need to use it, please do so under the supervision of a guardian. Please do not let children ride on the product or play with the product as a toy. Do not use the product in a room where infants sleep.
Problems that may arise in relation to cleaning products should be eliminated as soon as possible. Clear away power cords and small items on the floor to prevent the product from becoming blocked during the cleaning process. Fold over carpet edges and make sure hanging curtains, tablecloths, etc. are not touching the ground.
If there is an obstacle such as a staircase, test the product first to see if it can detect the edge of the obstacle without falling from it. Protective barriers should be placed at the edge of the obstacle to prevent products from falling. Make sure these protective barriers cannot cause personal injury.
Please follow the instructions in the manual when using the product and only use accessories recommended or sold by the manufacturer.
Ensure that the power supply voltage complies with the voltage indicated on the product.
Use only in indoor home environments. Do not use in outdoor, commercial or industrial locations.
Use only original rechargeable batteries and charging docks that are unique to the manufacturer. Do not use non-rechargeable batteries. For battery specifications, please refer to `Technical Data’. Make sure that dust compartments and filter materials are installed before using the product. · The product must not be used in an environment with open flames or fragile items, nor in extremely hot (above 40°C) or very cold (below -40°C) conditions. · Keep hair, clothes, fingers and other body parts away from the product’s opening and operating parts.
Do not use the product on wet or waterlogged surfaces.
The product should not be used to vacuum up items such as the following:
– Stones and waste paper.
– Flammable materials such as those used for printers or copiers.
– Cigarettes, matches, ash, or other items that may cause a fire.
Do not vacuum up any products that are already on fire. Do not place any items at the suction outlet. Do not use the product if the suction opening is blocked. Remove dust, cotton wool, hair, etc. from the suction opening to ensure smooth air circulation.
Use the power cord carefully to avoid any damage. Do not use the power cord to drag or pull the product from the product charging dock. Do not use the power cord as a handle. Do not clamp the power cord between doors. Do not pull the power cord around sharp corners.
Do not use the product if the power cord, power outlet or charging dock are damaged. Do not use the product if it is not working properly due to it having been dropped, damaged, or used outdoors, or if any water has entered the device. To avoid injury the product should be repaired by the manufacturer or its after-sales service. Please contact our customer service at: klantenservice@omnichannelgroup.com.
Turn off the product switch before cleaning and maintaining the product.

Product Instruction

What’s in the box

Robot Vacuum Cleaner
Charging Dock
Remote Control
Power Adapter
Side Brushes X 4
HEPAX 2
Cleaning Brush
Water Tank
Mopping Cloth
Instruction Manual

List of parts

Main Unit

Top View

Bottom View

Dust Compartment

Water Tank

Charging Dock Assembly

Remote Control

Parameters

| Product Model| MT-710
---|---|---
Input| DC 14.4V
Power| 30W
Battery Capacity| DC 14.4V Li-ion 2500mAh
Dust Compartment Capacity| 0.6L
Cleaning Time| 120 min
Charging Time| 300 min
| Battery| DC 3V(AAA)
---|---|---
Remote Control Method| Infrared
Transmission and Reception Distance| S5M
| Input| 100-240V/50-60Hz
---|---|---
Output| 19V/0.6A

Install 2 AAA batteries before using the remote control for the first time. Make sure the positive and negative ends are facing the correct way as marked in the battery compartment.

Attention

Please refer to the following guidelines to check the cleaning area before the cleaner starts operating.

Power cords and other items scattered on the ground may obstruct the product and must be removed.
Please roll up carpet tassels and do not use on deep-pile rugs.
The product may get stuck in gaps of less than 8 cm at the bottom of items of furniture. If you need to clean these areas, please remove the furniture.
If there are floors at different levels, a barrier must be used to prevent the product from falling from one floor to the other.

Rapid Operation

Install the Side Brushes

Install the right brush in the mounting port at the bottom right of the machine and the left brush in the mounting port at the bottom left of the machine and also ensure that the two side brushes are in place.

Charging Operation

Connect the adapter to the charging dock. Place the charging dock flat against the wall. Do not place objects within 1 meter to the left and right and within 2 meters to the front. Also make sure there are no objects nearby with highly reflective surfaces such as mirrors
Turn On The Main Unit
Press the Start/Pause key to turn on the main unit. It is advisable to keep the main unit in the charging dock after each use instead of immediately shutting it down. This will ensure it performs properly next time.

Main Unit Charge

Place the main unit in the charging dock and make sure the charging pole is properly positioned. Turn on the power switch and the robot will enter standby mode.
A flashing red light indicates that the battery needs to be charged.
A flashing blue light indicates the battery is charging.
Charging will have been completed when the blue light goes out.
Please charge continuously for more than 6 hours before using for the first time.
Note: Please make sure the charging pole is correctly positioned.

Start/Stop Cleaning

Start or Stop by pressing the main unit’s key or the remote control’s 10 key.
Note: Before selecting the mode, make sure that the outer ring of the key is blue and the main unit has been activated. If this is not the case, briefly press the main unit’s key . The main unit will enter sleep mode after 10 minutes of being on standby and if the key light is off.
If you need to select another mode, please refer to the Mode Selection section.

Mode Selection

In order to adapt to different floor conditions and achieve deep cleaning this product has a variety of cleaning modes which can be selected by remote control if necessary.

The remote control can be used to switch directly to any mode.

Before starting operations in a particular mode, you should make sure that the outer ring of the key is blue and that the main unit is activated. If this is not the case, briefly press the main unit’s key .

Fixed-point Mode

This mode is suitable for cleaning areas where dirt is concentrated. The cleaning operations will then focus on the designated area, and the cleaner will operate in accordance with a ‘spiral’ route.

Edge Mode

This mode is suitable for cleaning the corners of the room. The main unit will clean around the edge of a fixed object (such as a wall) and return to the charging dock.

Return Charging Mode

During the cleaning process the main unit will sense that it is low on power and will automatically return to the charging dock to be charged. You can also press the ‘Home’ button or press the ‘Power’ button twice to make the main unit return to the charging dock in order to be charged.

Twice Cleaning Mode

Select this mode by pressing the ‘Full Go’ button on the remote control. After initial cleaning the robot will now return to the charging dock until it is fully charged and will then automatically go back to cleaning again.

Suction Power Setting

Press the ‘Turbo’ button on the remote control to select this mode. There are three modes of suction power (Max/Standard/ Low). The Standard mode can be used for daily cleaning, while the Max mode will increase the suction power and the Low mode will reduce the noise.

The Low suction mode can be used to clean wooden floors and
tiled floors, the Standard mode can be used for everyday household cleaning and the Max mode can be used to clean rugs.

Roller Brush Assembly and Cleaning

Remove the roller brush cover plate, remove the roller brush, cut off the hair wrapped around it and then use the cleaning brush to clean it.

Installing the roller brush assembly: take out the vacuum assembly first, install the roller brush, put the cover back on and press it to lock.

Using the Water Permeable Mopping Cloth

This product is equipped with a water tank assembly. If mopping has to be done after the cleaning work has been completed, the dust compartment can be replaced with a water tank assembly. Please refer to the [Maintenance] section in this manual for the cleaning method.
Do not use the water tank assembly on carpet. When cleaning using the mopping cloth function, fold over the edge of the carpet to prevent foreign matter on the mopping cloth from soiling the carpet.
Please pay attention while cleaning and add or replace water in time. Remove the water storage compartment when adding water. When charging, be sure to remove the water permeable wiper assembly.

Add water
Open the water inlet cover and add sufficient water.

Attach the mopping cloth
Close the water inlet cover and attach the mopping cloth.

Install the water tank assembly
Press the dust compartment release button at the rear of the main unit to remove the dust compartment and replace the water tank assembly.

Maintenance

Dust Compartment and Filter

When cleaning and maintaining the main unit and its accessories, turn off the main unit and unplug the charging dock.

Remove the dust compartment, open the dust compartment cover and clean.
Remove the dust filter. The HEPA filter should not be washed but should be patted to remove the dust.
Flush the dust compartment and the primary filter.
Dry the dust compartment and the dust filter assembly and keep it dry to ensure a long life.

Let these parts dry naturally for more than 24 hours.

Water Tank Assembly

Cleaning the mopping cloth

Remove: When mopping is completed, remove the water tank assembly and remove the water permeable mopping cloth.
Maintenance: Rinse and dry the mopping cloth.
Remove: After mopping the floor, remove the water tank assembly and the water permeable cloth and pour off the remaining water in the water reservoir.

Side Brushes

Cleaning the Side Brushes
Pull out the side brush and wipe it with a clean cloth.

Other Assembly

Clean the universal wheel to reduce the amount of entangled hair.
Clear the sensor to maintain its sensitivity.
Use a dry cloth to clean the charging poles on the bottom of the main unit or the charging dock.

If you are not going to use the product for a long time, please remove the battery and keep it in a safe place. If the battery leaks, remove it and wipe the battery compartment clean.

This product uses a long-life battery and does not need to be replaced frequently. If you do need to replace it, you can contact our company’s after- sales service.

Alarms

Cause of Issue	Display light	APP content
Side brush	Red light on	Please check whether side brushes are jammed.
Fan abnormality	Red light on	Motor cooling error.
Roller brush	Red light on	Please check whether roller brush is jammed.
No dustbin inside	Red light on	Please check whether dustbin is installed

FAQ

Please install the right brush in the machine’s right bottom mounting port, the left brush in the left bottom mounting port and make sure that the two side brushes are in place.

What should I do if the robot does not work on my carpet?

We suggest that you do not use the robot to clean the carpet and instead set a boundary around the carpet with the app.

What should I do if the vacuum cleaner is not vacuuming at full strength?

First of all check whether the dustbin is full and the robot is fully charged. If this is the case you can try to switch it to a higher mode. In the case of persistent dust and debris try using the Spot Cleaning Mode.

What should I do if the robot cannot find the charging dock?

The charging dock should be placed against the wall with at least 1 meter of clearance on each side and 2 meters at the front. Sometimes you will need to put the robot back manually.

What should I do if the remote control does not work?

The remote control has an effective operating distance of 5 meters. Please make sure that the remote control is pointed at the main unit.
Replace the battery with a new one if it runs out of power.
Make sure the main unit’s power switch is turned on and has sufficient power to operate.
Wipe the infrared emitter of the remote control and the infrared receiver of the main unit with a clean towel.

Why does the main unit return to the charging dock after cleaning?

The main unit operates for variable periods depending on the complexity of the room, the amount of dust and debris and the cleaning mode.

WiFi Connection

Scan the QR code or search for `Smart Life’ and download the App.
Once the App has been installed, please follow the App instructions to register an account and login.
Open the APP and click {add device}, {Small Home App }, {Robot Vacuum}.
Make sure that the WiFi indicator is flashing / WiFi Push the front bumper and long press the key until the flashes. When the WiFi indicator flashes, click the .
Check to make sure that the indicator is rapidly blinking on the App.
Enter the WiFi account and password. (Currently only supports 2.4G WiFi so 5G WiFi cannot be connected.)

Distributed by: OCG Retail
Eemnesserweg 11-10
1251 NA Laren
the Netherlands
klantenservice@omnichannelgroup.com

www.blumill.shop

Documents / Resources

| BluMill MT-710 Robot Vacuum Cleaner [pdf] Instruction Manual
MT-710, Robot Vacuum Cleaner
---|---
| BluMill MT-710 Robot Vacuum Cleaner [pdf] Instruction Manual
MT-710, Robot Vacuum Cleaner, Vacuum Cleaner, Robot Cleaner, MT-710, Cleaner