KOAMTAC KDC470 1.0W UHF Reader User Guide
- June 14, 2024
- KOAMTAC
Table of Contents
KOAMTAC KDC470 1.0W UHF Reader
Toggling Read Modes
There are two read modes in which the SCAN button works: Barcode Mode and UHF mode. They are toggled by pressing the UP button for 3 seconds.
- When entered into this mode, 1 long and 1 short beep will be heard. Barcodes can be read with the SCAN button.
- When entered into this mode, 1 long and 2 short beeps will be heard. UHF tags can be read with the SCAN button.
Assembled Diagram
*KDC475 design is identical to the KDC470 with the exception of an angled scan window.
Basic Operation
-
To ensure that the UHF Reader is installed correctly, power on your KDC470/475/480/485 with the UHF reader installed.
-
If the UHF Reader was installed correctly, the KDC will beep once for power on, once again when it is booted up, followed by 2 quick beeps signalling that the UHF Reader is detected and ready for use.
If you do not hear 2 quick beeps, the UHF Reader may not have been correctly installed. Please verify that the installation is correct. -
The device must be in UHF modeto read UHF tags. This mode must be manually changed. To enter UHF mode, press the UP button on the KDC for 3 seconds. 1 long and 2 shortbeeps will sound.
Additional Companions
- HF Reader
- 0.5W UHF Reader
- Extended Battery
- Pistol Grip
- KDC600 mPOS
Additional Accessories
- Slot Charging Cradle
Basic Operation
Point the Reader in the direction of the tag(s) you want to read and press the SCAN button or pull the SCAN trigger to read the tags.
Changing UHF Tag Read Mode
The tag read mode is changed by scanning one of the following barcodes or by
pressing the DOWN key on the KDC470/475/480/485 for 3 seconds in RFID mode.
The tag read mode is changed in the following order: Active (default) read ->
Single read -> Multiple read
UHF Active Read Mode
Basic operation status. Simultaneous reading of multiple tags while pressing
the scan button (max. 10 minutes).
- 3 short beeps will occur when changing mode with the DOWN key.
Active Read Mode
Specs
RFID Details
- Standards Supported: EPC Class1 Gen2, EPC Gen2 V2 Nominal Read Range: 20’+ (6+ m) dependent on tag type and operating environment
- Frequency: US, EU, JP, KR
- Maximum Output Power : 30dBm + _ 1dBm
- Read Rate : 200 tags per second
- Stores: more than 400,000 RFID tags (96 bits EPC Data)
User Environment
- Ingress Protection Rating: IP64
- Operating Battery Characteristics
- Storage
- Humidity: 5% to 95% (non-condensing)
- UHF, Device Charging: 6000mAh Lithium-polymer battery of Pistol Grip
UHF Single Read Mode
Only one tag is read every time the scan button is pressed.
- short beep occur when changing mode with DOWN key.
Single Read Mode
Warning
For accurate measurement, straighten your arm and point the antenna in the
direction of the tag.
KDC UHF App
KDC UHF is a program which communicates with KOAMTAC’s Data Collector (KDC® )
via Bluetooth. It enables users to read UHF data, measure performance, and
configure the KDC on an iOS or Android device. This app is for demo purposes
and to aid developers using our SDK.
- Easily switch between barcode and UHF modes
- Easily switch between UHF tag reading modes
- Increase or decrease UHF power level
- Customize tag parameters
- Reading timeout settings
- Change UHF data types, region, and more!
UHF Multiple Read Mode
When the Scan button is pressed, multiple tags are read simultaneously for the
set time (default 10 seconds).
- Time setting can be changed in Settings ->Reading Timeout.
- 2 short beeps will occur when changing mode with the DOWN key.
Multiple Read Mode
Caution
Risk of fire or explosion if the battery is replaced by an incorrect type.
KTSync & SDK
KTSync® is a program which communicates with KOAMTAC’s KDC via Bluetooth. It
enables users to read and store data. KTSync is compatible with iOS, Android,
Windows, and Mac. It also supports wedging and downloading data from the KDC.
For more information about KTSync, please visit: www.koamtac.com/support/downloads/applications
The Software Development Kit (SDK) is the perfect solution for creating a custom application to collect data utilizing your KDC. KOAMTAC’s SDK covers all major development platforms: Android, iOS, Tizen, Windows, Xamarin, and Cordova. Developers may take advantage of the complimentary SDK and enjoy the full benefits of the KOAMTAC Developer Program.
For more information regarding the KOAMTAC Developer Program or to request the latest SDKs, visit: www.koamtac.com/support/downloads/sdk or e-mail sdk@koamtac.com.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
- Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
- This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>