BANTI FEZIBO Electric Stand up Corner Desk Instruction Manual

June 14, 2024
BANTI

**BANTI FEZIBO Electric Stand up Corner Desk Instruction Manual

**

ASSEMBLY INSTRUCTION

Caution

Keep children and pets away from the electric height-adjustable desk during the operation. Unplug the power cord during a thunderstorm or if you do not intend to use the desk for a long time.

Make sure desktop not touching the wall.

Ensure no obstacles in the desk’s path and no object above and 20” under the desk.

Working environment temperature 0-40℃, keep products away from corrosive gas, liquid and dusty objects.

It is strictly forbidden to disassemble the products privately to avoid that the failure of the products or the damage to the human body caused by electronic products, etc.

Although the product with anti-collision function, in order to avoid any pinching, please ensures that hands or other parts of your body are in a safe position during the operation. Anti-collision is not enabled during all resets.

Please read the following instructions carefully before start using the high adjustable desk. The company does not bear any warranty or liability for damage and human injury caused by any abnormal operation.

It is necessary to reset manually after the initial installation or power off.

Parts List

  • A – Column x 3

  • B – Foot x 3

  • C – Long Side Bracket x 2

  • D – Short Side Bracket

  • E – Girder E
    Parts List

  • F – Girder F
    Parts List

  • G – Girder G
    Parts List

  • H – Girder H
    Parts List

  • I – Cable management tray

  • J – Hook x 2

  • K – Connecting board x 4

  • L – Short Girder
    Parts List

  • M – Hand Controls

  • N – Control Box

  • O – Extension Cable x 2
    Parts List

  • P – Power Cord

Parts List

  • Q – M6x30 Screw x 12

  • R – M6x10 Screw x 26

  • S – ST4.8×13 screw x 32

  • T – ST3.5×16 screw x 4

  • U – Wooden pin x 6

  • V – M5 Allen Key

  • W – Cable clip x 6

Table board 1/2/3
Parts List

Tools Needed (Not Included)

  • Electric Drill

  • Phillips Screwdriver

Assembly

Step 1
Assembly

Checklist **

**

  • A – Column x 3

  • E – Girder E
    Parts List

  • F – Girder F
    Parts List

  • R – M6x10 Screw x 26

Step 2
Assembly

Checklist

  • L – Short Girder
    Parts List

  • G – Girder G
    Parts List

  • H – Girder H
    Parts List

  • R – M6x10 Screw x 26

Step 3

Assembly

Checklist

  • A – Column x 3

  • R – M6x10 Screw x 26

Step 4
Assembly

Checklist

  • C – Long Side Bracket x 2

  • D – Short Side Bracket

  • R – M6x10 Screw x 26

Step 5

Assembly

Checklist

  • B – Foot x 3

  • Q – M6x30 Screw x 12

Step 6
Assembly

Checklist

  • Table board 1/2/3
    Parts List

  • U – Wooden pin x 6

  • K – Connecting board x 4

  • S – ST4.8×13 screw x 32

Avoid excessive tightening screws

Step 7
Assembly

Checklist

  • S – ST4.8×13 screw x 32

Avoid excessive tightening screws

Step 8
Assembly

Checklist

  • R – M6x10 Screw x 26

  • S – ST4.8×13 screw x 32

  • J – Hook x 2

Step 9
Assembly

Step 10
Assembly

Checklist

  • I – Cable management tray

  • S – ST4.8×13 screw x 32

Avoid excessive tightening screws

Step 11
Assembly

Checklist

  • M – Hand Controls

  • N – Control Box

  • T – ST3.5×16 screw x 4

Avoid excessive tightening screws

Step 12 Cable Connection
Assembly

Checklist

  • O – Extension Cable x 2
    Parts List

  • P – Power Cord
    Parts List

  • W – Cable clip x 6

Instruction

Instruction

Manual Reset

 It is necessary to be reset manually after the initial installation and power off.

  1. Keep pressing down key till the desktop till display shows“E-1”and“rES”
    alternately and release the key.

  2. Keep pressing down key, the desktop will move slowly down and retum back till the display shows”27.6″/”70cm”.

  3. Release the key, the height-adjustable desk resetting finished.

Note: The anti-Collision function is not enabled during all resets. Please note that there is a potential risk of pinching in this case, and be sure no obstacles in the desk’s path.

Up and Down

  1. Keep pressing“up”key till the required height is reached.
  2. Keep pressing“down”key till the required height is reached.

Saving position

  1. Adjust the desktop to the height you want to save.
  2. Press “M” key till the display will show“S–”.
  3. Press“1”,and the display will show alternately as“S-1”and the desktop height.
  4. Press “M” key the first memory position is set successfully. Similar progress for 2 and 3 memory positions.

Anti-Collision function

Before use, please make sure removing obstacle in advance and human body is in the safe position

  1. Once the desktop encounters any obstacle in its path, the screen displays“E-2”。
  2. The desktop will move a defined distance in opposite direction, and it would be used normally after removing the obstacle.

Container and self-stop positions

Do not enable this function only when you are really need in some situation.

  1. Keep pressing the key“M”for 3 seconds till the display shows“S–”to enter setup menu.
  2. Press up key till the display flash as“HLP”.
  3. Press“1”,the display show alternately as“H-P”and current height.
  4. Keep pressing up or down key till the required upper limit position is reached.
  5. Press“M”,the desktop height will be showed and the shelf stop positionhas been set.
  6. Press “2”, the display will show ultimately “L-P” and current height, keep pressing down key till the lower limit position is reached, press “M”, the container stop position has been set.

Note: By this function would be used to limit the movement area of desktop, when the container
is underneath or any shelf above the desktop. Once it is set, the new upper or lower limitation will be stored.

Change the displayed Unit (cm/inch

  1. Keep pressing key “M” till the display show “S–” to enter the setup menu.
  2. Press “Up” key,the display will show “Unt”
  3. Press “1”, and the display will show alternately as “Unt” and the desktop height unit by “cm”.
  4. Press “M” key to save the unit as cm.
  5. Press “2”, and the display will show alternately as “Unt” and the desktop height unit by “inch” press key “M” to save the unit as inch.

Amend the desktop height displayed

  1. Keep pressing down key till the desktop till display shows“E-1”and“rES”alternately and release the key.

  2. Keep pressing key“M”till the display show“ Ur”and “ Off”alternately.

  3. Keep pressing key“M”till the display show“ Ur”and “ Off”alternately.

  4. Keep“Up”or“Dn”several times,till the display show“End”and height.
    (In this case, the unit is mm or inch when this system’s metric or imperial)

  5. Press“1”,“2”and“3”respectively, and to adjust the first number, the second number and the third number.If you click one,the number will increase by 1, till you get to the value you want.

  6. Press“M”the height has been changed to defined digit.

Note: The function enables you to change the height shows on the display based on the actual measurement.

Plug detection

The function can detect whether the motors are collected normally

  1. Once the display shows“E-3”and“rES”,it reminds you check whether any motors fail connected with control unit. Please connect the main cable again, wait at least 5 seconds.
  2. · Connect all the plugs
  3. Follow “Manual Reset ”procedure

Restore factory setting

With this functin, you can make the control unit to factory setting.

  1. Keep pressing “M” till the display shows “FAC”
  2. Press “M”,and the control unit to factory setting (including memory position, container-and shelf-stop position,etc).

Code meaning and Trouble shooting

Code meaning

Code Description Operation
E-1/rES Manual reset required Please perform a manual reset.
ovr Overloading Removed loadings desktop to less than 270lbs.
E-2 Anti-Collision function activated Remove any obstacle from desk’s path

of movement.
dut| Excessive use| Wait for around 15 minutes for your control box to cool down and become operational again.
E-3/rES| Communication interruption| Please unplug your desk for 20 minutes,check all cable connections and plug in for a manual reset.
E-4/rES| Difference in column heights (for over 1 inch)
E-5| Communication interruption| **** Please unplug your desk for 20 minutes,plug in and perform a manual reset.

Technical Data

Item Data
Input voltage AC 100-240V 50/60Hz
Output voltage 29V DC
Max loading 270 lbs / 1200 N
Height range 27.6″~47.3″/700mm~1200mm
Duty cycle 2 min on/ 18 min off

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals