DURATECH HS35 Hot Splash Heat Pump User Manual
- June 5, 2024
- DURATECH
Table of Contents
DURATECH HS35 Hot Splash Heat Pump
Box contents
Heat pump
|
Hose
---|---
Connection clamps
|
Manual
Safety information
Please read these instructions carefully before using the heat pump and keep them for future reference:
- Always keep the unit upright. If the unit has been tilted or put on its side, wait 24h before starting the heat pump.
- Put the unit on a flat, solid base.
- Do not drop the heat pump.
- The heat pump must always be installed outdoors.
- Check if the voltage indicated on the RCD of the heat pump corresponds to the local mains voltage before you connect the unit.
- Do not pull the mains plug with unnecessary force. Do not wrap the mains plug around the heat pump.
- Do not use the heat pump in combination with a transformer.
- If the heat pump is damaged during transportation, it must be replaced, please contact your service centre or similarly qualified persons in order to avoid a hazard.
- Always make sure the water connections of the heat pump are properly locked before you start using the machine.
- Never insert objects directly into the fan, as this will cause it to become blocked and damaged.
- The evaporator fins must not be damaged.
- This heat pump is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the heat pump by a person responsible for their safety.
- Children should always be supervised to ensure that they do not play with the heat pump.
- Disconnect the mains plug from the socket when the heat pump is not in use and before cleaning.
The heat pump will always perform very well, provided the following elements are present
-
Fresh air
-
Electricity
-
Swimming pool water
Specifications
Min. operating air temperature (°C) | 10 | Fan direction | horizontal |
---|---|---|---|
Heating Capacity A: 27°C/ W: 26°C * (kW) | 3,35 | Noise at 10m (dB(A)) | 48 |
Heating capacity A: 15°C/ W: 26°C(kW) | 2,65 | Refrigerant | R32 |
Power input(kW) | 0,56 | Refrigerant weight (kg) | 0,24 |
COP at A25/W25(C.O.P) | 6 | condensor | titanium |
COP at A15/W25(C.O.P) | 5,1 | Water connection (mm) | 32 |
Maximum pool volume(m³) | 12 | Nominal water flow (m³/h) | 2 |
Running Current(A) | 2,55 | Shipping dimensions(mm) | 310/360/385 |
Max Running Current(A) | 3 | Unit Net dimensions(mm) | 290/310/370 |
Power Supply (V/f/Hz) | 230v/1/50Hz | Net/Shipping weight(kg) | 15 |
Air flow (m³/h) | 700 |
Preparing the heat pump for use
Typical configuration & distance from the pool
The heat pump should be located at least 2m away from the swimming pool. In normal operation, the air taken by the heat pump is cooled down and water may condens on the fins of the evaporator and run out of the bottom of the unit.
| A free area of minimum 0,3 meter around the heat pump has to be kept clear
from any object(1).
---|---
| Put the heat pump on a flat, solid base.
| Do not obstruct the fan, leave at least 1.5m free unobstructed space in
front of the fan.
| All feeding of water treatment to the pool water has to be done downstream
of the heat pump(2)
| It is normal for condensation to come out of the heat pump. This is not a
leak or fault with the unit. If the humidity is very high, the condensation
could be a number of liters a day.
Hose connection
Step 1
**Step 2
**
| It is normal for condensation water to come out of the heat pump when it is
operating. This is not a fault or leak!
---|---
Electrical connection
The RCD is available in EU-version. UK-version is equiped with adaptor.
| Make sure your outlet is earthed
---|---
| The pool circulation pump must operate with the heat pump. Therefore,
connect them to the same circuit used for outdoor
Startup and settings
Guidelines
Cold/harsh weather conditions
Your heat pump is designed to operate in rainy weather conditions and
withstand frost using a specially created
Nofrost technology. However it is not recommended to leave it outside for long
periods of time (eg over winter).
After draining down the pool for the winter, store the heat pump in a dry
place.
Restarting the heat pump after long term storage
If your heat pump has been stored for a long time, perform the following steps when re-starting the system:
- Inspect the system for any debris or damage to the case.
- Clean the evaporator fins with a soft cloth if necessary. Make sure the evaporator fins are clean. Blocking the air intake will cause insufficient operation and will result in lower production of heat.
- Check the fan for blockages.
- Connect the water inlet and outlet.
- Turn on the pool water circulation pump to start the water flow to the heat pump.
- Restore electrical power to the heat pump and press the recer button on the R
Maintenance and error messages
- Check the water supply to and from the unit often. Low water flow or air entering into the pipes should be avoided, as this will diminish the heat pump performance and reliability. You should clean the swimming pool water regularly to avoid damage to the heat pump as a result of dirty pool water. Please check the information about warranty in section 9.
- The area around the heat pump should be clear and well ventilated. Clean the evaporator and evaporator guard regularly to maintain good air flow and efficiency.
- Check the power supply and cable connection often. In case of abnormal operation or a smell of burning near the electrical compartment, switch off the heat pump and contact your dealer.
- You should discharge the water at the bottom of the heat pump if the unit doesn’t work for an extended period of time.
The heat pump will show an error message in case of a problem. The following messages can occur:
| When TCO, AL1 or AL2 occur you can check the current water temperature by
pushing the up arrow. By pushing the down arrow you can check the current air
temperature inside the heat pump.
---|---
Environment
This heat pump should not be put into the domestic waste at the end of its useful life, but must be disposed at a central point for recycling of electrical and electronic domestic applications. By doing this you will help to preserve the environment.
Service & warranty
If you need service or information or if you have a problem, please contact
your local dealer. If needed they will contact the manufacturer to solve your
problem.
They are gladly willing to assist you!
You can find more information at www.hotsplash.eu
We warrant all parts to be free from manufacturing defects in materials and
workmanship for a period of two years from the date of retail purchase.
This warranty is limited to the first retail purchaser and is not
transferable. The liability of the manufacturer shall not exceed the repair or
replacement of defective parts and does not include any costs for labour to
remove and reinstall the defective part, transportation to or from the
factory, and any other materials required to make the repair. This warranty
does not cover failures or malfunctions resulting from the following:
- Failure to properly install, operate or maintain the heat pump in accordance with the installation guidelines provided in this manual.
- The workmanship of any installer of the product.
- Not maintaining a proper chemical balance in your pool accordance with our water chemistry guidelines provided in this manual.
- Abuse, alteration, accident, fire, flood, lighting, rodents, insects, negligence or acts of god.
- Scaling, freezing or other conditions causing inadequate water flow rate.
- Operating the heat pump at water flow rates outside the published minimum and maximum specifications.
- Use of non-factory authorized parts or accessories in conjunction with the product.
- Chemical contamination of combustion air or improper use of sanitizing chemicals, such as introducing sanitizing chemicals upstream of the heater and cleaner hose or through the skimmer.
- Overheating, incorrect wire runs, improper electrical supply, collateral damage caused by failure of O-rings, DE grids or cartridge elements, or damage caused by running the pump with insufficient quantities of water.
LIMITATION OF LIABILITY
This is the only warranty given by the manufacturer, No one is authorized to
make any other warranties on our behalf.This warranty is in lieu of all other
warranties, expressed or imlied, including but not limited to any implied
warranty of fitness for a particular purpose and merchantability. We expressly
disclaim and exclude any liability for consequential, incidental, indirect or
punitive damages for breach of any expressed or implied warranty.
This warranty gives you specific legal rights, which may vary, by country.
WARRANTY CLAIMS
For prompt warranty consideration, contact your dealer and provide the
following information: proof of purchase,model number, serial number and date
of installation. The dealer will contact the manufacturer for instructions
regarding the claim and determine the location of the nearest service point.
Contact details
[ **www.hotsplash.eu**](http://www.hotsplash.eu)
We reserve the rights to change all or part of the contents of this document without prior notice
Documents / Resources
|
DURATECH HS35 Hot Splash Heat
Pump
[pdf] User Manual
HS35 Hot Splash Heat Pump, HS35, Hot Splash Heat Pump
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>