VONROC VC504AC Wet & Dry Vacuum Cleaner Instructions

VONROC VC504AC Wet & Dry Vacuum Cleaner Instructions

1. SAFETY INSTRUCTIONS

Read the enclosed safety warnings, the additional safety warnings and the instructions. Failure to follow the safety warnings and the instructions may result in electric shock, fire and/or serious injury. Save the safety warnings and the instructions for future reference.

The following symbols are used in the user manual or on the product:

SAFETY NOTES
THIS APPLIANCE CAN BE USED BY CHILDREN AGED FROM 8 YEARS AND ABOVE AND PERSONS WITH REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES OR LACK OF EXPERIENCE AND KNOWLEDGE IF THEY HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE IN A SAFE WAY AND UNDERSTAND THE HAZARDS INVOLVED. CHILDREN SHALL NOT PLAY WITH THE APPLIANCE. CLEANING AND USER MAINTENANCE SHALL NOT BE MADE BY CHILDREN WITHOUT SUPERVISION. IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY THE MANUFACTURER, ITS SERVICE AGENT OR SIMILARLY QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. THE PLUG MUST BE REMOVED FROM THE SOCKETOUTLET BEFORE CLEANING OR MAINTAINING THE APPLIANCE.

1. Keep your work area clean: Cluttered work areas and workbenches are a source of injury.
2. The vacuum cleaner should be properly assembled before use.
3. Use only extension cords approved for outdoor use (when the vacuum is used outside) and make sure that they are always in good condition.
4. Protect the electric cables and, in particular, make sure that they are not crushed, pulled, or damaged by edges, sharp pieces, or moving parts; or damaged by corrosive liquids.
5. Do not use a damaged extension cord. Do not make any permanent or temporary repairs to the cable itself.
6. Do not use a vacuum cleaner that has a damaged electric cord. Have a new cable installed by an authorised service center.
7. Do not attach anything else to the socket, electric cords, or extension cord.
8. Before plugging your vacuum cleaner into the electrical outlet, make sure that the voltage and the outlet requirements match what is indicated on the label next to the cord.
9. Do not pull the device by the cord.
10. Your machine should always be turned off before unplugging it from the outlet or the extension cord.
11. Before leaving the device unsupervised (even for a brief time) turn it off and unplug it from the electrical outlet. This should also be done if there is a loss of power.
12. Do not underestimate its power. Always maintain a balanced and stable stance.
13. Keep children and pets away from the machine. When the machine is operating, everyone should stay at a safe distance.
14. The device should not be used by children or by persons who are not familiar with the device or who have not read this instruction manual.
15. The user of the device is responsible for the safety of others while using it.
16. The vacuum should only be used for its intended purposes.
17. Before performing any maintenance, adjustment or cleaning procedures on the vacuum cleaner, turn it off, unplug it from the electrical outlet, and wait for the motor to stop.
18. Be very careful when checking, cleaning, or performing maintenance on the device and wear thick work gloves to protect your hands.
19. Neither the security devices nor the electric cords should be modified or removed from the machine.
20. When using the machine, it should be kept steady and on a stable surface or supported by the body.
21. Only work in full daylight or with appropriate artificial light.
22. We recommend using some type of hearing protection for your ears.
23. If the machine vibrates abnormally, stop the motor and look for the cause immediately. Vibrations usually mean a problem.
24. The vacuum cleaner should be properly checked before each use. Do not use a machine that is not in perfect condition. If you notice a problem that could constitute a danger to the user, have the machine repaired before using it.
25. For safety reasons, replace worn or damaged parts. Use only manufacturer approved replacement parts. Parts from sources other than the manufacturer may not fit properly or may be dangerous or cause injuries. The power cord can only be replaced by specialized customer service centres.
26. Only use the vacuum cleaner in areas that are dry and protected from bad weather. Do not use it outside when it is raining.
27. Store the vacuum in a dry place, out of the reach of children.
28. Do not leave the power cord lying around once clean-up is done; someone could trip.
29. Take care when emptying extremely heavy tanks.
30. To avoid spontaneous combustion, empty the tank after every use.
31. Do not use this machine to vacuum up flammable or combustible liquids, such as gasoline, photocopier powder, or volatile substances; and do not use the machine in areas where these liquids are present. Do not vacuum up acids.
32. Do not vacuum up any materials that are toxic, cancer causing, combustible, or any other dangerous materials, such as asbestos, asbestos dust, arsenic, barium, beryllium, lead, pesticides, or any other substances hazardous to your health.
33. Extreme caution should be used when vacuuming up wood or charcoal, soot, cement, plaster, or plasterboard dust. These particles are extremely fine and can pass through the filters affecting the motor’s performance or be blown into the air. If necessary, therefore we strongly recommend a HEPA filter in combination with a dust collection bag when cleaning these types of materials.
34. Do not vacuum up anything that is burning or smouldering, such as cigarettes, cigarette butts, matches, or hot ashes.
35. Never vacuum up salt water; it may destroy the motor.

SAFETY WARNINGS SPECIFIC FOR BLOWING
a) Direct air discharge at work area only. Never at people or animals.
b) Risk of flying objects. Keep bystanders away from the work area.
c) Always wear safety goggles before using the blowing function.

Electrical safety
When using electric machines always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions and also the enclosed safety instructions.

Always check that the power supply corresponds to the voltage on the rating plate.

Connecting to the power supply
Check that the power supply and plug used in accordance with your machine. Have a look at the rating plate on the machine. Any changes should always be carried out by a qualified electrician.

Warning! This machine must be earthed. If not properly earthed this machine can cause an electrical shock. Be sure that the power supply outlet is earthed. If there is any doubt, have it checked by a qualified electrician.
Warning! Avoid contact with the terminals on the plug when installing (removing) the plug to (from) the power supply outlet. Contact will cause a severe electrical shock.
Replacing cables or plugs
Immediately throw away old cables or plugs when they have been replaced by new ones. It is dangerous to insert the plug of a loose cable in the wall outlet.

Using extension cables
Only use an approved extension cable suitable for the power input of the machine. The minimum conductor size is 1.5 mm². When using a cable reel always unwind the reel completely

2. MACHINE INFORMATION

Intended use
The vacuum cleaner is intended for domestic wet and dry vacuuming in, for example, the house, work room, car or garage. The vacuum cleaner is equipped with a blowing function. It can be used to blow dust and debris. The device is not suitable for commercial or industrial use.

TECHNICAL SPECIFICATIONS

DESCRIPTION
The numbers in the text refer to the diagrams on pages 2-4.

1. On l / off 0 / ll automatic mode switch
2. Carrying handle
3. Blowing port
4. Power cord storage
5. Filter-cleaning button
6. Top section
7. Locking clamp
8. Container
9. Base
10. Wheels
11. Castor wheels
12. Drainage outlet
13. Drainage outlet cap
14. Vacuum port
15. Power socket with automatic on/off control
16. Nozzles storage
17. Hose
18. Handle adapter
19. Removable handle
20. Suction tubes
21. Wet and dry floor nozzle
22. Round brush nozzle
23. Crevice nozzle
24. Car vacuum tool
25. Power tool adapter
26. Dust collection bag
27. HEPA filter
28. Foam filter
29. Intake port
30. Float
31. Filter cage

3. ASSEMBLY

Before assembly, always switch off the machine and remove the mains plug from the mains.

1. Press the container (8) on the base (9) as shown in Fig. B. Make sure the base (9) is securely fastened.

2. Fit the filter (27,28). Ensure to mount the correct filter, depending on the application:
   • For dry vacuum cleaning, carefully slide the HEPA filter (27) over the filter cage (31) making sure the entire cage (31) is covered as shown in Fig. C-1.
   • For wet vacuum cleaning, carefully slide the foam filter (28) over the filter cage (31) making sure the entire cage (31) is covered as shown in Fig. C-2.

3. Place the top section (6) on the container (8). 4. Connect the suction hose (17).
   • For vacuuming (Fig. E-1), connect the suction hose (17) to the vacuum port (14).
   • For blowing (Fig. E-2), connect the suction hose (17) to the blowing port (3).

4. Connect the handle (19) to the handle adapter(18). One or more suction tubes (20) can be fit to the handle (19) to extend it (fig. A).

5. Connect the desired nozzle to the handle adapter(18), handle(19) or suction tubes (20).

Wet and dry floor nozzle (21)
The floor nozzle is designed for domestic wet and dry vacuuming in, for example, the house, work room, or garage.

Round brush nozzle (22)
The brush is designed to vacuuming solids from small areas.

Crevice nozzle (23)
The crevice nozzle is designed for domestic wet and dry vacuuming, edges and other areas that are difficult to access.

Car vacuum tool (24)
The brush is designed to vacuuming solids from small areas. For example from car seats.

Power tool adapter (25)
Adapter for connecting suction hose with a power tool.

4. OPERATION

If the vacuum cleaner accidentally tips over, the shut-off float (30) mechanism may cover the motor vacuum port and stop the suction. If this happens, simply stand the vacuum upright and turn it off until the float (30) returns to its normal position.
Do not vacuum without a filter!

Switching on / switching off / automatic mode (Fig. F)
The on l / off 0 / ll automatic mode switch (1) has three settings:
I On, power to socket.
0 Off, power to socket.
II Automatic mode, power to socket, as soon as the power tool is switched on, the vacuum cleaner starts with some delay. If the power tool is switched off, the vacuum cleaner continues to run for 5 seconds in order to vacuum up the remaining dirt in the suction hose.

Dry vacuuming (Fig. A, C ­ F)
Clean the HEPA filter (27) regularly to maintain the suction power.
To avoid the HEPA filter (27) becoming clogged, we recommend the additional use of a dust collection bag (26).
Fine dust, such as dust from cement, soot and plaster are too fine to be used with only the HEPA filter (27) and risk getting into the motor and damaging it. Therefore we strongly recommend a dust collection bag (26) when cleaning these types of materials.
Clogged dust collection bag (26) can burst ­ therefore make sure to replace the dust collection bag in a timely manner!

1. Press the power switch (1) into the ” OFF/0″ position and remove the mains plug from the mains.

2. Unlock the locking clamp (7) and remove the top section (6).

3. Before vacuuming, remove all dirt and debris from the container (8).

4. Carefully slide HEPA filter (27) down over the filter cage (31) making sure the whole cage (31) is covered as shown in Fig. C-1.

5. For vacuuming with dust collection bag (26):
   • Hold the cardboard collar tightly and slide the rubber protective element as far as possible onto the intake port (29) as shown in Fig. D.
   • When everything is in place, unfold the bag (26) out and position it around the inside walls of the container (8).

6. Reattach the top section (6) again and lock the locking clamp (7).

7. Insert one end of the hose (17) into the vacuuming port (14). Fully unwind the suction hose (17).
   For vacuuming:

8. Connect the mains plug.

9. Press the power switch (1) into the ” ON/I” position to start your vacuum cleaner.

10. The machine now is ready to use for dry vacuum cleaning.

11. Press the power switch (1) into the ” OFF/0″ position to switch off your vacuum cleaner.

For automatic mode vacuuming (working with power tools):

1. Adapt the power tool adapter (25) to the dust extraction outlet of the power tool. Using a knife if necessary.
2. Connect the power tool adapter (25) to the handle adapter (18) and connect it to the power tool dust extraction outlet.
3. Connect the mains plug of the power tool to the power socket (15).
4. Connect the mains plug.
5. Press the power switch (1) into the ” Automatic mode / II” position and start working to start your vacuum cleaner. The vacuum cleaner is automatically switched on/off via the power tool. As soon as the power tool is switched on, the vacuum cleaner starts with some delay. If the power tool is switched off, the vacuum cleaner continues to run for some seconds in order to vacuum up the remaining dirt in the suction hose (17).
6. Press the power switch (1) into the ” OFF/0″ position to switch off your vacuum cleaner.

Wet vacuuming (Fig. A, C, E ­- F, H)

The vacuum cleaner is equipped with a float (30). The suction power decreases when the maximum filling level is reached. Switch the vacuum cleaner off (1) immediately. Remove the plug from the socket and empty the container (8).

Clean the float (30) at regular intervals, and check it for damage. Otherwise, its function can be impaired.
Never reach into the water to be suctioned up. Danger of electric shock.
Immediately switch (1) the machine off if foam forms or liquids escape!
Do not use a dust collection bag (26)!

1. Press the power switch (1) into the ” OFF/0″ position and remove the mains plug from the mains.
2. Unlock the locking clamp (7) and remove the top section (6).
3. Before wet vacuuming, remove the dust collection bag (26), the HEPA filter (27) and remove all dirt and debris from the container (8).
4. Carefully slide foam filter (28) down over the filter cage (31) making sure the whole cage (31) is covered as shown in Fig. C-2.
5. Reattach the top section (6) again and lock the locking clamp (7).
6. Insert one end of the hose (17) into the vacuuming port (14). Fully unwind the suction hose (17).
7. Connect the mains plug.
8. Press the power switch (1) into the ” ON/I” position to start your vacuum cleaner.
9. The machine now is ready for wet vacuum cleaning.
10. Press the power switch (1) into the ” OFF/0″ position to switch off your vacuum cleaner.
11. Raise the hose (17) so that the liquids drains into the container (8).
12. Empty the container (8) immediately after suction cleaning because it is not designed to store liquids.

Blow function (Fig. A, E ­ F)

Your vacuum cleaner is equipped with a blowing function. It can be used to blow dust and debris.

1. Press the power switch (1) into the ” OFF/0″ position and remove the mains plug from the mains.
2. Unlock the locking clamp (7) and remove the top section (6).
3. Before blowing, remove the dust collection bag (26), the filter (27, 28) and remove all dirt and debris from the container (8).
4. Reattach the top section (6) again and lock the locking clamp (7).
5. Insert one end of the hose (17) into the blowing port (3) on top of machine. Fully unwind the suction hose (17).
6. Connect the mains plug.
7. Press the power switch (1) into the ” ON/l” position to start your vacuum cleaner.
8. The machine is now ready for blowing dust and debris.
9. Press the power switch (1) into the ” OFF/0″ position to switch off your vacuum cleaner.

Finish operation (Fig. A)

1. Turn off (1) the machine and disconnect the mains plug.
2. Opening the drainage outlet (12) to allow the vacuumed liquid to drain out.
3. Close the drain outlet (12).
4. Remove the top section (6) and empty the container (8).
5. Clean the machine with a soft cloth.
6. Stow away the mains cable and accessory at the machine. Store the appliance in a dry room.

5. MAINTENANCE

Before cleaning and maintenance, always switch off the machine and remove the mains plug from the mains.
Clean the machine casings regularly with a soft cloth, preferably after each use. Make sure that the ventilation openings are free of dust and dirt. Remove very persistent dirt using a soft cloth moistened with soapsuds. Do not use any solvents such as gasoline, alcohol, ammonia, etc. Chemicals such as these will damage the synthetic components.

Container
Empty the container (8) immediately after suction cleaning because it is not designed to store liquids.

1. Opening the drainage outlet (12) to allow the vacuumed liquid to drain out.
2. Close the drain outlet (12).
3. Remove the top section (6) and empty the container (8).
4. Clean the machine with a soft cloth.

Filter cleaning system (Fig. A, G)
When the suction is getting weaker, please remove the tubes (20) and jam the handle (19) by hand (while the vacuum cleaner is working). Then press the filter cleaning button (5) 10 times. This will clean the filter (27) and recover the suction force.

Filters (Fig. A)
For optimal performance it is recommended to regularly change the filters (17,18) depending on level of use.

1. Carefully remove HEPA (17) or foam (18) filter.
2. Use a mild soap and water solution to clean the filter and afterwards rinse with clean water.
3. Allow filter to air dry before installing and using again.
4. Re-install the filter.

Float and filter cage (Fig. H)
Clean the float (30) and filter cage (31) regularly with a soft cloth, and check it for damage. Otherwise, its function can be impaired.

ENVIRONMENT
Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.

Only for EC countries
Do not dispose of power tools into domestic waste. According to the European Guideline 2012/19/EC for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.

WARRANTY
VONROC products are developed to the highest quality standards and are guaranteed free of defects in both materials and workmanship for the period lawfully stipulated starting from the date of original purchase. Should the product develop any failure during this period due to defective material and/or workmanship then contact VONROC directly.
The following circumstances are excluded from this guarantee:

• Repairs and or alterations have been made or attempted to the machine by unauthorized service Centers;
• Normal wear and tear;
• The tool has been abused, misused or improperly maintained;
• Non-original spare parts have been used.

This constitutes the sole warranty made by company either expressed or implied. There are no other warranties expressed or implied which extend beyond the face hereof, herein, including the implied warranties of merchantability and fitness for a particular purpose. In no event shall VONROC be liable for any incidental or consequential damages. The dealers remedies shall be limited to repair or replacement of nonconforming units or parts.

The product and the user manual are subject to change. Specifications can be changed without further notice.

©2021 VONROC
WWW.VONROC.COM
2103-25

References

• VONROC Gereedschap & Tuin artikelen

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>