HAMPTON BAY JAO1501L-2/BR LED Low Voltage Path Light User Guide
- October 30, 2023
- HAMPTON BAY
Table of Contents
Item #1008 454 051
Model # JAO1501L-2/BR
Item #1008 454 055
Model # JAO1501L-2/CP
Item #1008 454 049
Model # JAO1501L-2/AL
Use and Care Guide
LED LOW VOLTAGE PATH LIGHT
PACKAGE CONTENTS
Assembly and Installation
Attaching and installing the light
WARNING: Never use a hammer to insert the light into the ground.
- Insert the fixture wire on the wire connector (C) into the groove located on the top of the ground stake (B).
- Screw the ground stake (B) into the lamp body (A). Ensure the fixture wire on the wire connector (C) stays in the center of the groove of the ground stake (B) to avoid damage to the fixture wire.
- Prepare a hole in the installation location. Use a tool such as a screwdriver to prepare the installation hole to ensure that the hole is not larger than the ground stake (B).
- Install the ground stake (B) in the ground by pushing on the lamp body (A).
Connecting the wires
WARNING: The wire connector (C) contacts have sharp edges for piercing
the main low voltage cable. To avoid injury, do not touch the metal contacts.
CAUTION: The wire from low voltage power unit should be 12-16 AWG type
underground low Energy Circuit Cable.
IMPORTANT:
- Protect the wiring by routing it in close proximity to the light fitting, or next to a building structure such as a house or a deck.
- The landscape wire and connector can also be hidden under stone or buried under grass at a maximum depth of 6 in. (15.24 cm).
- Do not install the fixture within 10 ft. of a pool, spa, or fountain.
- Do not submerge the fixture in water.
- Place the wire connector (C) on opposite sides of the low voltage cable (not included) from the transformer (not included) where the fixture will be located.
- Align and fit the main low voltage cable vertically to the slot of the wire connector (C).
- Press the wire connector (C) together until it is locked around the main low voltage cable. The pre-set prongs will pierce the cable insulation and establish contact with the electrical wire inside.
- Once the wire connector (C) is in place, it is recommended to wrap it with electrical tape (not included).
- After all fixtures are installed, turn on the transformer.
Care and Cleaning
- Clean the fixture with a soft dry cloth.
- Do not use any cleaners with chemicals, solvents or harsh abrasives.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| The fixture will not light. | ❑ There is no power. |
❑ There is a disconnection or break in the wire.
❑ The transformer setting is incorrect.| Check the outlet and ensure that a
breaker or GFCI circuit has not been tripped. Follow the wires from the
fixture and ensure a continuous connected path back to the transformer.
Check the settings on the transformer.
The light flickers (one fixture).| There is a loose wire
connector to the fixture.| Tighten the wire connector and ensure the metal
contacts pierce the insulation on the low voltage cable from the transformer.
The lights flicker (all fixtures).| There is a loose connection at the
transformer.| Unplug the transformer from the outlet and visually inspect the
positive and negative connecting points. Each wire should be securely screwed
in and not in contact with any other.
Warranty
WHAT IS COVERED
The manufacturer warrants this lighting fixture to be free from defects in
materials and workmanship for a period of five (5) years from date of
purchase.
This warranty applies only to the original consumer and only to products used
in normal use and service. If this product is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or
replacement of the product at the manufacturer’s discretion, provided that
the product has not been damaged through misuse, abuse, accident,
modifications, alterations, neglect or mishandling.
WHAT IS NOT COVERED
This warranty shall not apply to any product that is found to have been
improperly installed, set-up, or used in any way not in accordance with the
instructions supplied with the product. This warranty shall not apply to a
failure of the product as a result of an accident, misuse, abuse, negligence,
alteration, or faulty installation, or any other failure not relating to
faulty material or workmanship. This warranty shall not apply to the finish on
any portion of the product, such as surface and/or weathering, as this is
considered normal wear and tear.
The manufacturer does not warrant and specifically disclaims any warranty,
whether express or implied, of fitness for a particular purpose, other than
the warranty contained herein. The manufacturer specifically disclaims any
liability and shall not be liable for any consequential or incidental loss or
damage, including but not limited to any labor / expense costs involved in the
replacement or repair of said product.
Contact the Customer Service Team at 1-855-HD-HAMPTON or visit
HAMPTONBAY.COM.
Cable Selection
12 VOLT TAP
| Cable Length
---|---
Total Fixture Wattage| 0-50 feet| 51-100 feet| 101-150 feet
0-60 Watts| 16 AWG| 16 AWG| 14 AWG
61-120 Watts| 16 AWG| 14 AWG| 12 AWG
121-180 Watts| 14 AWG| 12 AWG| Not recommended
181-240 Watts| 14 AWG| 12 AWG| Not recommended
241-300 Watts| 12 AWG| Not Recommended| Not recommended
600W Transformer = (2×300) Watts| 12 AWG| Not Recommended| Not recommended
900W Transformer = (3×300) Watts| 12 AWG| Not Recommended| Not recommended
15 VOLT TAP
| Cable Length
---|---
Total Fixture Wattage| 0-50 feet| 51-100 feet| 101-150 feet
0-60 Watts| 16 AWG| 16 AWG| 16 AWG
61-120 Watts| 16 AWG| 16 AWG| 12 AWG
121-180 Watts| 14 AWG| 14 AWG| 12 AWG
181-240 Watts| 14 AWG| 14 AWG| 12 AWG
241-300 Watts| 12 AWG| 12 AWG| Not recommended
600W Transformer = (2×300) Watts| 12 AWG| 12 AWG| Not recommended
900W Transformer = (3×300) Watts| 12 AWG*| 12 AWG| Not recommended
* NOT RECOMMENDED FOR HALOGEN LANDSCAPE LIGHTS
This data is provided as a general guideline. Actual performance will depend
on the installation layout, the fixtures, and the condition of the cable.
NOTE: Most LED landscape lighting fixtures can operate with full
illumination from 9V down to as little as 6V. It is possible to have extended
length runs with LED fixtures that go beyond the specifications shown in the
guidelines above.
FCC Warning
Warning: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>