bol com JS-HJ001 Hot Melt Glue Gun Instruction Manual

June 5, 2024
bol com

Hot Melt Glue Gun

Operation Instruction

Project Name: Hot melt glue gun
Document No.: HH/JS-HJ001
Controlled state: controlled
Version: A/0

一. Product Name: Hot Melt Glue Gun
二. Product Features:

  1. Use ceramic PTC thermistor as the heating element to quickly heat up and automatically maintain a constant temperature; save energy and extend the life span of the hot melt glue gun.

  2. Product technical parameters: working voltage: 100V-230V; frequency: 50/60Hz; product internal working temperature: 110℃~220℃.

  3. The heater has been designed for heat insulation to ensure safe use.

  4. The shell is made of nylon material with high temperature resistant, high flame retardant.

  5. Use a silicone protective sleeve at the glue outlet to prevent burns due to high temperature

  6. Equipped with a metal bracket, it can support the gun nozzle to prevent scalding the table in the working gap, Scope of application

  7. Plastics: bonding of toy models, artificial flowers, decorations, handicrafts, pearl cotton, etc.

  8. Wood products: bonding of toy models, wood products, handicrafts, etc.

  9. Metals: bonding of toy models, small pieces of metal materials, handicrafts, etc.

  10. Electronics: bonding of PCB boards, internal wires, electronic components, LED lights, etc.

  11. Cloth and paper: bonding of cloth products, rope, leather, paper, cardboard, books, packaging boxes, etc.

  12. Foods: bonding of milk packaging boxes, food packaging color boxes., Operation method

Select the corresponding size hot melt glue stick for the hot melt glue gun; insert the hot melt glue stick from the end of the glue gun, turn on the power AC 110V to 240V; preheat for 5-8 minutes, gently pull the trigger to make the hot melt glueflows outfrom the gun mouth.

Melt viscosity: 5300cps

Working conditions:

  1. Working Temperature: -10~+55Cº
  2. Relative humidity: 0%
  3. Conditions: dust-free, no-steam, water-free, oil-free, saltfree and so on
  4. Cooling mode: natural cooling
Matters needing attention:
  1. Select the applicable hot melt glue stick. <Diameter ¢ 7mm and ¢12mm>
  2. Please do not let any part of your body touch the nozzle during the working process; prevent scalding by the overheating nozzle.
  3. Please do not pull the glue stick out of the working gun, because the molten glue may cause burns or damage the gun.
  4. If the glue gun stops working for more than 5 minutes, please cut off the power supply to avoid damaging by the reflow of melt.
  5. non-specialized persons and those who have not read the instructions, please do not operate the glue gun
  6. Children aged 0-8 are prohibited from using
  7. Check the power supply, switch and power indicator light of the glue gun before using. If any parts are damaged, stop using it immediately. Professionals with corresponding qualifications are required to replace original parts for repairs, and unqualified personnel are forbidden to repair by themselves.
  8. It is not suitable for bonding objects in direct contact with water or liquid.
  9. Turn off the power after use. After it is completely cool, clean up the remaining glue, put it in the box and store it in a safe place.
  10. When the workpiece or material is affected by liquid, water vapor, moisture, and high temperature, the adhesion part will fall off by itself.
  11. Causes of failures and treatment measures
Problem Cause Solution
feeding difficult glue stick melted incomplete **Heat for 300

seconds
glue feeding too fast| Lightly pushing the material device
glue stick melting point too high| Use recommended glue stick
glue overflow| glue stick diameter too small| Use recommended glue stick
vigorously push material device| Push material device slowly
glue filament| melted glue is not completely discharged| Adjust glue flow in advance
gun nozzle not cleaned up| Clean up nozzle
Failed to glue| no power| Turn on the power
glue stick melted incomplete| Heat for 300 seconds**

maintenance and cleaning
  1. Turn off the power before maintenance and cleaning.
  2. After the hot melt adhesive has solidified, it can be removed with a blunt tool, and no solvent should be used for cleaning.
  3. Pay attention to keep the feeding device clean and tidy.
  4. Check the power cord and shell.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals