bol com AM18 Bladeless Fan User Manual
- June 5, 2024
- bol com
Table of Contents
BLADELESS FAN
User Manual
Please read this manual carefully before using the product and keep it
properly
Applicable models: AM18
Fittings
IMPORTANT SAFETY INSTRUCTIONS
Warning
In order to avoid fire, electric shock, and personal injury, please be sure to
follow the following requirements, others please follow the relevant national
and local electrical regulations.
IMPORTANT SAFETY INSTRUCTIONS
BEFORE USING THIS APPLIANCE READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS IN
THIS MANUAL AND ON THE APPLIANCE
When using an electrical appliance, basic precautions should always be
followed, including the following:
WARNING
THE FAN AND THE REMOTE CONTROL BOTH CONTAIN MAGNETS.
- Pacemakers and defibrillators may be affected by strong magnetic fields. If you or someone in your household has a pacemaker or defibrillator, avoid placing the remote control in a pocket or near the device.
- Credit cards and electronic storage media may also be affected by magnets and should be kept away from the remote control and the top of the appliance.
WARNING
These warnings apply to the appliance, and also where applicable to all tools, accessories, chargers, or mains adaptors. TO
REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:
- This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or reasoning capabilities, or lack of experience and knowledge, only if they have been given supervision or instruction by a responsible person concerning the use of the appliance in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be made by children without supervision.
- Ensure the appliance is fully assembled in line with the instructions before use. Do not dismantle the appliance or use it without the loop amplifier fitted.
- Do not allow it to be used as a toy. Close attention is necessary when used by or near children. Children should be supervised to ensure that they do not play with the appliance.
- Use only as described in this Operating Manual. Do not carry out any maintenance other than that shown in this manual, or advised by the Helpline.
- Suitable for dry location ONLY. Do not use outdoors or on wet surfaces and do not expose to water or rain.
- Do not handle any part of the plug or appliance with wet hands.
- Do not operate any appliance with a damaged cable or plug. Discard the appliance or return it to an authorized service facility for examination and/or repair. If the supply cable is damaged it must be replaced by a Seller service agent or a similarly qualified person in order to avoid a hazard.
- If the appliance is not working as it should, has received a sharp blow, has been dropped, damaged, left outdoors, or dropped into water, do not use and contact the Helpline.
- Do not stretch the cable or place the cable under strain. Keep the cable away from heated surfaces.
- Do not run cable under carpeting. Do not cover the cable with throw rugs, runners, or similar coverings. Arrange cable away from traffic area and where it will not be tripped over.
- Do not unplug by pulling on the cable. To unplug, grasp the plug, not the cable. The use of an extension cable is not recommended.
- Do not put any object into openings or the inlet grille. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow.
- Do not use any cleaning agents or lubricants on this appliance. Unplug before cleaning or carrying out any maintenance.
- Always carry the appliance by the base, do not carry it by the loop amplifier.
- Tum off all controls before unplugging. Unplug before connecting any tool or accessory.
- To avoid a tripping hazard wind the cable when not in use.
- Do not use near furnaces, fireplaces, stoves, or other high-temperature heat sources.
- Do not use in conjunction with or directly next to an air freshener or similar products. 19. Choking hazard – This remote control unit contains a small battery. Keep the remote control away from children and do not swallow the battery. If the battery is swallowed seek medical advice at once.
READ AND SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE ONLY
Do not pull on the cable.
Do not store near heat sources.
Do not use near naked flames.
Warning
Please use the appliance at the voltage specified on the nameplate
• the reason for fire and electric shock| Please use the appliance at the
voltage specified on the nameplate
• the reason for fire and electric shock
---|---
Take the plug when you plug it in and actually plug it in
• If the insertion is not complete, it may be the cause of electric shock,
heat, fire, etc| Be sure to remove the plug from the socket when maintaining
• the reason for electric shock and injury.
Please do not use wet hands on the plug and operation panel.
• the reason for electric shock| When pulling out the plug, do not pull out
the power cord but pull out the plug
• There may be an electric short circuit and fire
It must not be modified, and no one other than the maintenance technician can
disassemble it.
• If repairing please go to the store where you purchased it.| Dust the plug
regularly.
• Dust accumulation, due to moisture, will make poor insulation, is electric
shock, heat, and fire
If you hear an abnormal sound, stop running and unplug
| If you do not use it for a long time, be sure to unplug it from the socket.
Please do not put it on the side of the TV, radio or electronic equipment, keep the distance of 2 meters or more.
| Please do not use it in high temperaturwet, fire accessories, or oily places
Please do not use it in an unstable place.
| Do not clean it with insecticide, benzene, banana oil, etc.
Do not let the wind blow the body for a long time.
| Do not pour water on the fan and the operation panel.
Product Introduction
Functions specifications
-
The bladeless fan buzzer sounds on and the displays enter the standby state.
-
The highest level of the fan is level, and the lowest is level.
The default level is the level when the fan is turned on for the first time. -
If the fan is in a standby state without power off, the level position is the same position as the last shutdown when the fan is turned on again.
-
If the fan is not powered off
When in the standby state, the level will be the last power-off level when it is turned on again; -
The panel keys have the function of turning the fan on and off to adjust the speed of the head
Press the buzzer once when shutting down, the fan is turned on, and every time
you press the buzzer once to adjust the level;
Press and hold for seconds after turning on the fan. After hearing the beep,
the fan begins to rotate. Press it for seconds to turn off the rating
After booting, press and hold for seconds to turn off.
Remote Control Operation:
The functions of the remote control are as follows
-
ON/OFF: in the running state, press the button to start up the fan and run.
After pressing the button again, the fan slows down and stops, and enters the standby state. -
Wind speed level plus in the running state, press the key level plus.
When the level is in the 8th level, press the key again and the buzzer will ring twice to indicate that the top-level has been reached -
Wind speed level minus in the running state, press the key level minus.
When the level is in the first level, press the key again. and the buzzer will ring twice to indicate that the lowest level has been reached: -
Rotating: in the running state, press the button fan rotating, and press again to stop rotating.
-
Timer plus: in the running state, press the button to enter the timing mode.
The initial timing mode is 1 hour. The LED displays “1H”.When the timer is 12, press the button again to exit the timing mode. The LED shows the wind speed level -
Timing minus: in the running state, press the button to enter the timing mode.
when the timing mode is larger than 1 hour, the time will be reduced for each keypress. When the timer is 1H, it can not be reduced again.
Loop Adjustment
- After the operation stops, swing in the direction you like.
- please hold the mainframe with one hand. Adjust the air supply loop front and rear
Installation
- Align the winding loop to the base vertically (accurate groove)
- Press the base lock mark and then rotate the loop; as shown below.
Fan abnormality check method
- When an exception occurs, please investigate the following points
- if there is a problem, please go to the shop to negotiate
1 It does not work when plugging in the power.
- please recognize whether the plug is really into the socket
- if the power button is pressed, whether the display screen is on or off;
2 air volume weak
- if the air inlet/outlet is blocked, please remove the blockage.
- whether the air volume is adjusted to a strong level
3 The remote control cannot be operated
- Is the battery drained? Is the battery placed incorrectly?
4. Unable to operate normally after power failure
- Plug out and plug it in again 5 when there is a bad smell
- it is possible that parts are damaged. Please stop the operation.
Cleaning and Maintenance
- Be sure to unplug the plug when performing maintenance. Please do not use a wet hand to pull the plug. Inadvertent movement may result in injury and electric shock.
- when maintenance, please do not touch water, or splash water, there may be electric shock, short circuit, fault
- In the case of dirty, it can be wiped with a damp cloth containing a neutral detergent. It is easier to decontaminate. When using a neutral detergent, wipe the water-containing cloth completely, then use a dry cloth wipe.
- please confirm whether the air inlet on the back of the host is blocked by dust. Using a soft brush to remove dust and dust will be the cause of failure when the dust is gathered. If there is dust, please maintain it in time
- please confirm whether the air outlet of the air supply loop is blocked by dust. If there is dust, please maintain it in time.
- The effect will be good if use a vacuum cleaner to remove dust regularly.
- Banana oil, light oil, alcohol, lamp oil, benzene, abrasive powder, alkaline lotion, brush, etc. may cause discoloration and deterioration of the paint surface resin, please do not use.
- If it is used for a long time, there will be dust and moisture accumulation between the plug and the socket, which may cause a fire. Please pull out the plug and wipe it with a dry cloth.
- If the power cord is damaged, in order to avoid danger, it must be replaced by the manufacturer and its maintenance department.
Preservation methods
- Put the fan into a nylon bag and foam after maintenance
- The remote control and other accessories are placed in the box and placed in a dry place.
Repair service
-
GUARANTEE FORM.
• there is a GUARANTEE FORM on the back of this manual
• the GUARANTEE FORM should be marked in the sales store “purchase date of the sales store” and other details, please properly guarantee -
when entrusted for repair
• Even during the warranty period, if there is a guarantee on the warranty, there may be a charge for the repair.
• if the warranty is expired, the fan will be repaired at the customer’s request in charge. -
repair the holding of performance parts
• the minimum holding time for repairing performance parts (parts necessary to maintain the function of the product) is two years after the manufacturer -
read the details
• in the process of use and usually different state, immediately stop using, please entrust the sales shop for testing and repair, the customer does not do their own decomposition. -
standard service time in design
• The standard service life of this fan in design is 5 years.
• If the service time exceeds the design standard, fire, injury, and other accidents may occur due to aging.
• The number of years is calculated according to the time setting table and standard use conditions. -
there is anything unclear about the repair service
• For repair service, and product negotiation, please contact the purchasing store, or manufacturer
Warranty Card
GUARANTEE FORM
Product Model|
Purchase Date|
Customer Name|
Customer phone|
Product Warranty Record
Warranty Date| (Warranty Period One Year)
Fault Cause|
Customer Signature|
Maintenance Personnel|
Merchant stamp|
Remarks|
Please fill in the details of all the sections of this warranty card and stamp
the dealer’s seal, otherwise, it will be invalid.
1. The product is free of charge under normal use within one year from the
date of purchase.
2. The inspection and maintenance fees will be charged if more than one year.
3. During the warranty period, it will not be repaired free of charge if the
following conditions occur:
a. unable to present warranty card or proof of purchase (invoice or receipt)
b. Maintenance beyond the warranty period.
c. Damage caused by disassembly or modification
d. Malfunctions or damage caused by mistakes (such as prolonged use in harsh
environments).
e. The appearance is natural dirt.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>