Parrot Uncle BBHDA199A 52 in White Indoor Flush Mount Ceiling Fan with Light and Remote Instruction Manual

Parrot Uncle BBHDA199A 52 in White Indoor Flush Mount Ceiling Fan with

Light and Remote

Product Information

The BBHDA199A is a ceiling fan manufactured by Parrot Uncle. It is designed to provide both cooling and lighting functionality to your space. The fan has a stylish and modern design that can complement any room decor. The fan is equipped with a powerful motor to ensure efficient cooling and comes with a built-in light fixture for added convenience.

Specifications

• SKU: BBHDA199A
• Nominal Voltage: 120Vac
• Nominal Output (Motor): 25W
• Nominal Output (Light): 18W

Installation Instructions

Safety Information

Before starting the installation process, please ensure the following safety precautions:

1. Shut off power at the fuse or circuit breaker.
2. Follow the National Electrical Code NASI/NFPA70-1999 and local electrical codes for wiring.
3. Hire a qualified licensed electrician for electrical installation.
4. Use UL listed outlet boxes marked acceptable for fan support of 35lbs (15.9kg) or less.
5. Ensure a minimum clearance of 7 ft. (2.1m) from the trailing edge of the blades to the floor.
6. Avoid operating the reversing switch while the fan blades are in motion. Stop the fan and blades before reversing the direction.
7. Avoid placing objects in the path of the blades.
8. Exercise caution when working around or cleaning the fan to avoid personal injury or damage.

Assembly Instructions

Follow these steps to assemble and install the Parrot Uncle ceiling fan:

1. Remove the rubber motor stops on the bottom of the fan before  installing the blades or testing the motor.
2. Mount the fan to an outlet box marked acceptable for fan support of 35lbs (15.9kg) or less.
3. Use the provided screws to secure the fan to the outlet box.
4. Check and retighten all setscrews as necessary before installation.
5. Refer to the electrical diagrams (for reference only) and make appropriate electrical connections.
6. Turn off the electricity at the main fuse box before wiring. If you lack electrical wiring knowledge or experience, contact a licensed electrician.
7. If using a light kit, ensure it is UL-listed and marked suitable for use with this fan model.
8. Splice the conductors and push them carefully up into the outlet box, separating the grounded conductor and equipment-grounding conductor on one side, and the ungrounded conductor on the other side.
9. Refer to the instructions packaged with the light kits and switches for proper assembly if applicable.

FAQ

Q: Can I use a solid-state speed control device with this fan?

A: No, to avoid the risk of fire or electric shock, do not use this fan with any solid-state speed control device.

Q: Do I need to hire an electrician for installation?

A: Electrical installation should be performed by a qualified licensed electrician to ensure safety and compliance with electrical codes.

Q: Are the light kits and switches included with the fan?

A: No, light kits that are not packed with the fan must be UL-listed and marked suitable for use with the specific model of fan you are installing. Switches must be UL General Use Switches. Please refer to the instructions packaged with the light kits and switches for proper assembly.

Safety Information

1. To reduce the risk of electric shock, the electricity has been turned off at the circuit breaker or fuse box before begin.

2. All wiring must be in accordance with the National Electrical Code NASI/NFPA70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.

3. The outlet box and support structure must be securely mounted and capable of reliably supporting 35lb.(15.9kg). Use only UL listed outlet boxes marked “Acceptable for Fan Support of 35lbs (15.9kg) or less.”

4. The fan must be mounted with a minimum of 7 ft. (2.1m) clearance from the trailing edge of the blades to the floor.

5. Do not operate the reversing switch while the fan blades are in motion. You must turn the fan off and stop the blades before you reverse the blade direction.

6. Do not place objects in the path of the blades.

7. To avoid personal injury or damage to the fan and other items, please be careful when working around or cleaning the fan.

8. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL-listed and marked suitable for use with the model fan you are installing. Switches must be UL General Use Switches.
   Refer to the instructions packaged with the light kits and switches for proper assembly.

9. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box. and the ungrounded conductor on the other side of the outlet box.

10. All setscrews must be checked and retightened where necessary before installation.

• WARNING: TO reduce the risk of personal injury, do not bend the blade brackets (also referred to as flanges) during assembly or after installation. Do not insert objects in the path of the blades.
• WARNING: Remove the rubber motor stops on the bottom of the fan before installing the blades or testing the motor.
• WARNING: To reduce the risk or fire or electric shock, do not use this fan with any solid-state speed control device.
• WARNING: To avoid possible electric shock, turn the electricity off at the main fuse box before wiring. lf you feel you do not have enough electrical wiring knowledge or experience, contact a licensed electrician.
• WARNING: Electrical diagrams are for reference only. Optional use of any light kit shall be UL-listed and marked suitable for use with this fan.
• WARNING: To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked”Acceptable for fan support of 35lbs. (15.9 kg) or less “and use the screws provided with the outlet box.

TECHNICAL INFORMATION

Product Parts

Installation & Operating Instructions

1. Check the existing outlet box (not included) to ensure it is securely fastened to at least two points in a structural ceiling member and can support the full weight of the fan.Once verified, install ceiling plate to the outlet box using the screws and washers provided.
   DANGER: A loose outlet box can cause the fan to wobble and increase the fan’s potential to fall, which could result in serious injury or death.

2. Hang the motor assembly from the ceiling bracket assembly using the hook on the ceiling bracket assembly and the cable loop from the motor assembly as shown. Install remote control After connections have been made, put the white and green leads to one side and the black leads towards the other side, the connection should be turned upward and carefully push leads into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and the ungrounded conductor on the other side.

3. Remove the three screws from the ceiling plate assembly and retain for later.

4. Align the wide tab of motor assembly to the wide notch of ceiling bracket. Carefully secure the motor housing onto the mounting slots on ceiling bracket by twisting in a clockwise direction. Be sure the receiver and all wiring are tucked into the motor housing and is not pinched. Once the motor assembly is flush with your ceiling, replace the previously removed screws and securely tighten all three screws.

5. Secure the three blades using the blade screws through the holes located on the bottom of the motor assembly.

6. Remove one of the three screws in the support bracket at the bottom of the motor assembly. Retain the screw for later and slightly loosen the remaining two screws.

7. Assemble the switch housing assembly to the support bracket using the two key slots in the switch housing assembly. Replace the previously removed screw and securely tighten all three screws.

8. Remove one of the three screws in the switch housing assembly. Retain the screw for later and slightly loosen the remaining two screws.

9. Connect the 2 single pin connectors from the light kit to the 2 single pin connectors from motor assembly. Assemble the light kit to the switch housing assembly using the two key slots. Replace the removed screw and secure all three screws.

10. Secure the shade to the switch housing assembly by twisting in a clockwise direction. Twist the shade gradually until it snaps onto the switch housing assembly. Do not over-tighten.

Remote Overview

WIRING SCHEMATIC  DIAGRAM FOR RECEIVER

POWER PARAMETER  LIST

• Voltage: 120 V
• Fan (max.): 25W
• Lamp (max.): 18W

Adopt RF wireless digit emission technique, biunique controlled , coincident code rate is less than one millionth. (Emitter and receiver must be sent back to the factory for maintenance if damaged.) The receiver can be controlled by any angles of the emitter in prescriptive space, unrestricted by direction. With the memory function, the controller can save the status( light and direction ) while the supply power OFF and resume to the original after reload the power supply.

FUNCTION INSTRUCTION OF EMITTER

1. indicated light
2. ON/OFF the fan
3. Turn up the speed of the fan
4. Turn down the speed of the fan
5. Direction of the fan (reverse switch) Timing control of the fan
6. Short press: ON/OFF the light
   • Long press: Adjust the brightness of the light
7. Timing control of the fan
8. 3V CR2032 battery x 1pcs

• a. WARNING: Chemical Burn Hazard. Keep batteries away from children.
• b) This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
• c) The cells shall be disposed of properly, including keeping them away from children; and
• d) Even used cells may cause injury

KINDLY REMINDERS:

1. 1. If the emitter can not control the fan, learning code matching mode is used between the emitter and receiver.
   Turn “ON” the supply power within 30 seconds and press the emitter’s “ ” button for 5 seconds, it can load
   normally after hearing the long sound “bee”, which means learning successfully and it can work normally.
   (PS: Learning mode is not accepted after turn “ON” the supply power for 30 seconds)
   2. When the emitter cannot control the receiver, please check the battery switch touching normally or not, correction of the positive and negative, full or empty of power.
   3. When the emitter cannot control the receiver, please check is there any existence of similar remote-controlled products nearby, then check whether they works, because remote-controlled products with the same frequency will disturb each other.
   4. The low voltage of battery will affect the sensitivity of the emitter and the signal reception accordingly(the indicated light will flash out its warning when the battery get low voltage), and must be replaced if the battery is getting low voltage.
   5. Please take out the battery from the emitter when leaving unused for long time.
   6. The maximum load of lighting see the above“POWER PARAMETER LIST”
   PS: please connect the ground wire correctly, otherwise it may cause the light micro-light or flash
   7. When installing the fan, the fan ceiling cover doesn’t press the antenna (or other wire), it is easy to break down the wire and short-circuit.

SIZE OF PRODUCT

TROUBLESHOOTING GUIDE

FAN / REMOTE IS NOT WORKING

• Ensure the remote is within the 20-foot range of the receiver
• To reset the remote control:
  1. Turn off the power to fan using the wall switch or circuit breaker.
  2. Remove batteries from the remote. 3) Wait 10 seconds. 4) Replace batteries and turn the power on
• Check batteries to ensure they are good and oriented correctly
• Check to make sure the frequency switches (DIP Switches) from the remote to the receiver are set to the same frequency
• Check the main and branch circuit fuses or breakers
• If using a Variable Speed Wall Switch, ensure it is specifically designed for use with a ceiling fan.
• Check the line wire connections to the fan and the switch wire connections in the switch housing per the instructions
• If the fan still does not work, please contact Customer Service Support@ParrotUncle.com

THE FAN IS NOISY

• Make sure all motor housing screws are tight
• Make sure the screws that attach fan blade to the motor are tight
• Make sure the wire nut connectors are not rattling against each other or the interior wall of the switch housing
• Allow a 24-hour break-in period. Most noises associated with the new fan may disappear during this time
• if using a ceiling light kit, make sure the glassware is secured tightly
• Make sure there is a short distance/gap from the ceiling to the top of the canopy. The canopy should not touch the ceiling!
• Make sure your ceiling box is secure and that the rubber insulating pads are used between the mounting bracket and outlet box

THE FAN WOBBLES

Verify all blades and blade bracket screws are secure (most fan wobble problems are caused by loose parts). Once fan is properly installed,run the ceiling fan for 10 minutes to let the fan self-adjust. If wobble occurs after running the fan for 10 minutes, verify blade level using the following process:

• a) select a point on the ceiling above the tip of one of the blades. Then select the fan blade and measure from the center of the selected blade to point on the ceiling. Rotate the fan until the next blade is positioned and repeat the measurement using the same point from the ceiling for every blade. Measurements should be within 1/8 inch.
• b) If all deviations are less than 1/8 inch and the fan continues to wobble, please contact Customer Service Support@parrotUncle.com to order a complimentary Blade Balancing Kit
• If all deviations are less than 1/8 inch and the fan continues to wobble, please contact Customer Service Support@ParrotUncle.com to order a complimentary Blade Balancing Kit.

LIGHT IS NOT WORKING

• Loose electrical connections.
• Shut off the branch circuit electricity at the fuse box or breaker panel and check the LED light fixture assembly electrical
• connectors for proper installation.
• To reset the remote control:
  1. Turn off the power to fan using the wall switch or circuit breaker.
  2. Remove batteries from the remote.
  3. wait 10 seconds.
  4. Replace batteries and turn the power on

AFTER INSTALLATION

Wobble
The fan blades have been adjusted in the factory to minimize any wobble
Note: ceiling fans tend to move during operation due to the fact that they are mounted on a rubber grommet. If the fan was mounted rigidly to the ceiling, It would cause excess vibration. Movement of A few centimeters is quite acceptable and does not suggest any problem to reduce the fan Wobble : Please check that all screws which secured the mounting bracket and downrod are secure.

Balancing a wobbling ceiling fan:

1. Check that all blade and blade arm screws are secure.
2. Most fan wobbling problems are caused when blade levels are unequal. Check this level by electing a point on the ceiling above the tip of one of the blades. Measure this distance. Rotate the fan until the next blade is positioned for measurement. Repeat for each blade. The distance deviation should be equal within 1/8″(0.32cm).
3. If the blade wobble is still noticeable, Interchanging two adjacent (side by side) blades can redistribute the weight and possibly result in smoother operation.

Warning: To reduce the risk of personal injury, Do not bend the blade arm while installing, Balancing the blades, or cleaning the fan. Do not insert foreign objects between rotating fan blades.

Noise

When it is quiet (especially at night) you may hear occasional small noises. This is normal. Please allow a 24-hour “breaking-in” period, Most noises associated with a new fan disappear during the time.

Care and cleaning

1. Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free cloth to avoid scratching the paint finish. Please make sure to turn off electricity power before you clean your fan
2. Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock.
3. Motor has permanently lubricated ball bearing. No need to oil.

Note: Make sure the power is off at the electrical panel box before you attempt any cleaning or repairs.

References

• Uncle.com
• Diversified choices for ceiling fans and lighting — ParrotUncle

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>