BRESSER BR-SP60 Portable 60W LED Fresnel Light with Remote Control Instruction Manual

BR-SP60 Portable 60W LED Fresnel Light with Remote Control
Instruction Manual

GENERAL WARNINGS

DANGER OF BODILY INJURY!
Do not use it in the presence of children or animals. Store out of reach of children and animals.
**RISK OF MATERIAL DAMAGE!
Make sure that no one can trip over the connection cables of the device. The device could be knocked over.
Only use the recommended power cable or the recommended battery for the power supply!
The manufacturer accepts no liability for voltage damage caused by the use of an unsuitable power supply!
DANGER OF AN ELECTRIC SHOCK!
This device contains electronic parts that are powered by a power source (power adapter). Only use the device as described in the manual. Otherwise, you run the DANGER of an ELECTRIC SHOCK. Never bend, squeeze or pull power cables, connecting cables, extensions or connectors. Protect cables from sharp edges and heat. Check this device, cables, and connections for damage before use. Never attempt to operate a damaged device or a device with damaged electrical parts! Damaged parts must be replaced immediately by an authorized service agent.
Operate the device only in a completely dry environment and do not touch the device with wet or damp body parts.
RISK OF GLARE!
Make sure that people and animals do not look into the light. The high luminosity can cause glare to the eyes and afterimages. This impairment of vision can lead to accidents.
FIRE/EXPLOSION HAZARD!**
Always place the device in such a way that it cannot tip over and ensure that it is stored in a reasonably safe place.

• Keep children and animals away from the device! They could knock the device over.
• Make sure that no one can trip over connection cables. The device could be knocked over.
• Do not expose the device to high temperatures. Do not short circuit the device or dispose of it in the fire! Excessive heat and improper handling can cause short circuits, fires, and even explosions!
• Only use the recommended power supply*!

IMPORTANT NOTE!
Do not disassemble the device! In the event of a defect, please contact your dealer. They will contact the Service Center and can arrange the return of this device for repair if necessary. Disconnect the power supply by pulling the mains plug when the appliance is not in use, in case of a longer interruption of operation, and before any maintenance and cleaning work.
Place your device so that it can be disconnected from the power supply at any time. The power outlet should always be near your appliance and should be easily accessible, as the plug of the power cord serves as a disconnect device from the main supply. To disconnect the unit from the mains, always pull the mains plug and never pull the cable!
Do not subject the device to excessive vibrations.

PRODUCT INFORMATION

The 56mm (2.2”) Fresnel has an expansive spot-to-flood beam angle range of 20 to 80 degrees at the spot setting. The fixture has a daylight output of 5600K and comes with a white and an orange filter to change the color temperature. The CRI rating is typically 95+, indicating an accurate rendition of color. The fixture is dimmable from 10-100%. The brightness change can be made locally on the fixture and viewed on the unit’s LCD screen. It can also be made remotely from a 2.4G wireless controller once they are paired with the same channel from 01-99. You can also daisy-chain several lights together and make brightness adjustments from a single controller after pairing the remote controller with all the lights on the same channel.

EC DECLARATION OF CONFORMITY
BRESSER has issued a „Declaration of Conformity“ in accordance with applicable guidelines and corresponding standards. The full text of the CE declaration of conformity is available at the following internet address: www.bresser.de/download/F004354/CE/F004354_CE.pdf
UKCA DECLARATION OF CONFORMITY
Bresser UK Ltd. has issued a „Declaration of Conformity“ in accordance with applicable guidelines and corresponding standards. The full text of the UKCA declaration of conformity is available at the following internet address: www.bresser.de/download/F004354/UKCA/F004354_UKCA.pdf
Bresser UK Ltd. • Suite 3G, Eden House,
Enterprise Way, Edenbridge, Kent TN8 6HF, Great Britain

WARRANTY & SERVICE

The regular guarantee period is 2 years and begins on the day of purchase. You can consult the full guarantee terms and details of our services at www.bresser.de/warranty_terms.

http://www.bresser.de/warranty_terms

DELIVERY CONTENT
LED Fresnel Light (A), remote control (B), power adapter (C), power cable (D)

PARTS OVERVIEW

1. LED Display

2. Power switch

3. Spot Setting
   Adust the beam angle range of 20 – 80 degrees by turning the knob

4. Dimmer knob
   The knob provides dimmer control and remote channel selection. Turn to adjust the brightness (10-99) or to select a channel (01-99) Short press to get from brightness control to remote channel select. Before the use of the remote, the controller must be paired with the same channel.

5. Power socket

6. Locking screw (tilt joint)

7. Fixing screw (tripod connection)

8. Tripod connection

9. Tilt joint

10. Battery holder

11. Barn doors

12. Two-pin C7 socket

13. Barrel connector

14. Euro plug

15. Two-pin C7 plug
    (B) Remote controller:

16. power button

17. – button

18. + button

19. menu button

ESTABLISHING THE POWER SUPPLY

1. Insert the barrel connector (13) of the power adapter (C) into the power connection socket (5) on the LED light.
2. Insert the two-pin C7 plug (15) of the power cable (D) into the two-pin C7 socket (12) of the power adapter (C).
3. Insert the Euro plug (14) of the power cable (D) into a wall socket.

INSTALLING THE V-MOUNT BATTERY (optional)

1. Slide the fully charged battery* (type NP-F970) into the holder (10) from the side so that the battery clicks into place.
2. To remove, slide the battery out of the holder in the opposite direction.

TURNING ON THE LED LIGHT

1. Establish the power supply for the device (insert battery or connect power cable).
2. Press the power switch (2) to switch the device on or off. The lighting is switched on with the settings of the last use.

Important: Disconnect the device from the power supply if it is not going to be used for a long period of time!
BRIGHTNESS ADJUSTMENT

1. Turn the dimmer knob (4) clockwise to increase the brightness.
2. Turn the dimmer knob (4) counterclockwise to decrease the brightness.

CHANNEL ADJUSTMENT (for remote control)

1. Short press the dimmer knob (4) to reach the channel select mode
2. Briefly turn the color dimmer knob (4) to set the desired channel.

ADJUSTING THE TILT ANGLE

1. Hold the fresnel light and slowly loosen the locking screw (6) for the tilt joint (9).
2. Move the lamp head to the desired position and tighten the locking screw (6) again hand-tight.

MOUNTING ON A TRIPOD (optional)

1. Loosen the fixing screw (7) for the tripod connection (8) so far that the opening of the tripod connection is exposed.
2. Place the lamp with the opening of the tripod connection on a tripod and tighten the fixing screw firmly.

Note: The light can also be held with the handle. In this way, the lighting position can be changed quickly and easily.

REMOTE CONTROL

SELECTING A CHANNEL

1. Press the Menu button (19) three times to go to the channel menu.
2. Press – or + (17/18) to choose the desired channel.
3. Press the Menu button (19) to confirm your selection.

POWERING ON/OFF THE UNIT

1. You can use the power button (16) on the remote-controlled to switch on the unit
2. Long press the Power button (16) to switch off the unit.

MOVING THROUGH THE MENU
Press the Menu button (19) to move through the menu.
Press 1x = shows 10 “Brightness” 10 = 10%
Press 2x = shows 56 “Colour temperature” 56 = 5600 K
Press 3x = shows 01 “Channel” 01 = 1
ADJUSTING BRIGHTNESS

1. By default, the brightness level is 10% when the device is turned on.
2. Press – or + (17/18) to increase or decrease the brightness.

DISPOSAL

Dispose of the packaging materials properly, according to their types, such as paper or cardboard. Contact your local waste disposal service or environmental authority for information on the proper disposal.
Do not dispose of electronic devices in the household garbage! As per the Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner.
In accordance with the regulations concerning batteries and rechargeable batteries, disposing of them in normal household waste is explicitly forbidden. Please make sure to dispose of your used batteries as required by law — at a local collection point or in the retail market. The disposal of domestic waste violates the Battery Directive. Batteries that contain toxins are marked with a sign and a chemical symbol.
1 battery contains cadmium
2 battery contains mercury
3 Cd¹ Hg² Pb³ battery contains lead

TECHNICAL DATA

Service

Please contact the service center first for any questions regarding the product or claims, preferably by e-mail.
e-mail: service@bresseruk.com
Telephone*: +44 1342 837 098
BRESSER UK Ltd
Customer Support
Suite G3, Eden House
Enterprise Way
Edenbridge, Kent TN8 6HF
United Kingdom

• Number charged at local rates in the UK (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs.

Bresser GmbH
Gutenbergstraße 2
46414 Rhede · Germany
Bresser UK Ltd.
Suite 3G, Eden House
Enterprise Way, Edenbridge,
Kent TN8 6HF, Great Britain
www.bresser.de
@BresserEurope
Errors and technical changes reserved.
Manual_F004354_BR-SP60_en-nl-de_BRESSER_v012022a

References

• Bresser | Startseite | Expand Your Horizon mit BRESSER

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>