Alecto WS-1050 Digital Weather Station User Guide

: June 5, 2024
: Alecto

Table of Contents

Alecto WS-1050 Digital Weather Station
INSTALLATION
BATTERY REPLACEMENT
SPECIFICATIONS
WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Alecto WS-1050 Digital Weather Station

INSTALLATION

Power supply:

Slide down the battery cover at the rear of the indoor unit and remove it.
Place 2 batteries, type AAA, 1.5Volt, according to the markings inside the battery compartment (see A). Batteries are not included. After you’ve installed the batteries, the indoor unit will start scan for 3 minutes for any nearby outdoor unit. That’s why you should follow the instructions 4, 5, and 6 within those 3 minutes.
Unscrew the battery cover with a crosshead screwdriver.
Place 2 batteries, type AAA, 1.5Volt, according to the markings inside the battery compartment (see B).
Set the channel switch to your desired transmitting channel 1, 2 or 3. Please select the same channel on the indoor unit that you’ve set on the outdoor unit.
Press the MAX/MIN ” channel button of the indoor unit, placed above the battery compartment. Each time you press this button, the receiver will change to the next channel. The display will show which channel number is selected. To make the outdoor unit transmit again:
Press the “TX” button (see C) to have the outdoor unit transmit again when the registration has failed. As soon as both the indoor and outdoor unit have been found, the outdoor temperature will appear on de display of the indoor unit (see D).
Now replace the battery covers on the indoor and outdoor units.
Both units can be suspended from a screw (see E) or placed on a surface using the foldable table support (see F).
Temperature display setup:
The temperature unit can be expressed in ºC or ºF. Press the “ MAX/MIN ” button to switch between ºC and ºF.
Maximum and minimum display:
De minimum temperature measured and the maximum temperature measured can be displayed.
Briefly press the “ MAX/MIN ” button to show the minimum temperature.
Briefly press the “ MAX/MIN ” button again to show the maximum temperature.
Press and hold “ MAX/MIN ” for two seconds to reset the maximum and minimum temperature.
Positioning tips:
Never place the indoor unit in direct sunlight and keep it away from heat radiating objects (lights, heaters, etc.)
Never place the indoor unit next to large metal surfaces or heavy electrical equipment, ensuring proper reception of the radio-controlled signals.
The outdoor unit is not waterproof. Always place this unit on a spot protected against rain and wind.
The distance between the indoor and outdoor unit should be no more than 50 meters.
De transmission range can be affected by nearby devices transmitting on 433.92 MHz. The range also depends on obstacles. Concrete walls between the outdoor and indoor unit will reduce the transmission range more than plaster walls.Rechargeable batteries: You can choose to use normal (alkaline) or rechargeable batteries in both the indoor and outdoor unit. However, rechargeable batteriesprovide a lower voltage, reducing the lifespan and accuracy of the WS-1050. Rechargeable batteries must be charged using an external charger.

BATTERY REPLACEMENT

Indoor unit:
After replacing the batteries of the indoor unit, all memories and settings will be deleted.
Outdoor unit:
After replacing the batteries of the outdoor unit, you’ll need to re-register it to the indoor unit. To do this, follow the instructions of chapter ‘Installation’. Always make sure to set the same channel number on the indoor and outdoor unit using the “CH” button.
RESET/SYSTEM ERROR
If the WS-1050 shows a possible error, you may have to reset the indoor and outdoor units.

Remove the batteries from the indoor and outdoor unit.
Wait for at least 10 seconds and then replace the batteries.
Follow the registration procedure (see paragraph ‘Installation’). After several seconds the indoor and outdoor units will have recognised each other and you can start using the WS-1050 again. If you still have no connection or sound, please contact the customer service of Alecto.

SPECIFICATIONS

Indoor unit:
- indoor temperature measurement range: 0°C ~ +50°C (32°F ~ +122°F)
- resolution: 1°C (1.8°F)
- Power supply: 2x 1.5V battery, size AAA, alkaline
Outdoor unit:
- outdoor temperature measurement range : -30°C ~ +70°C
- resolution: 1°C (1.8°F)
- Power supply: 2x 1.5V battery, size AAA, alkaline
- Transmission frequency: 433.92 MHz
- Power: -11.26 dBm
- Range: up to 50 meters

WARRANTY

For the Alecto product, you have a warranty of 24 months from the date of purchase. During this period, we guarantee the free repair of defects caused by material and workmanship errors. All this subject to the final assessment of the importer.
HOW TO HANDLE:
If you notice any defect, first refer to the user’s manual. If you can’t find a decisive answer here, please contact your dealer with a clear complaint description. The dealer will then accept the product with this proof of warranty and the dated proof of purchase and ensure a speedy repair or otherwise send it post-paid to the importer. THE WARRANTY BECOMES NULL ANDVOID: In case of improper use, incorrect connections, leaking and/or incorrectly installed batteries, use of unoriginal parts or accessories, negligence and in case of defects caused by moisture, fire, flooding, lightning and natural disasters. In case of unauthorised modifications and/or repairs performed by third parties. In case of incorrect transportation of the device without adequate packaging and when the device is not accompanied by this warranty card and proof of purchase. The warranty does not cover connecting cables, plugs and batteries. All further liability, especially concerning any consequential damages, is excluded.