MEMPHIS VGB0001 Grills Pro Wi-Fi Controlled 28-Inch Instruction Manual
- June 5, 2024
- MEMPHIS
Table of Contents
MEMPHIS VGB0001 Grills Pro Wi-Fi Controlled 28-Inch Instruction Manual
Model Number VGB0001
Appendixes and Model-Specific Information
Clearance To Combustible Materials
WARNING: The structure and surrounding objects MUST maintain the specified minimum clearance to combustible materials.
Built-in structures constructed of wood or other combustible materials may require the use of the OPTIONAL Built- In Heat Shield Kit to maintain the required clearance to combustible materials. The grill may be supported by either the three support brackets, or the four leveling feet. Please note that there must be at least 3/8” (1.0cm) clearance between the bottom of the grill and the structure.
Maintain the clearance to combustible materials as specified below.
A MAJOR CAUSE OF FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES
(AIR SPACES) TO COMBUSTIBLE MATERIALS. IT IS OF UTMOST IMPORTANCE
THAT THIS PRODUCT BE INSTALLED ONLY IN ACCORDANCE WITH THESE
INSTRUCTIONS.
Built-In Grill Island Dimensions
WARNING: See clearance to combustible materials, when designing and constructing a built-in island. Built-In islands must be built to the specifications listed below.
The owner and/or builder are responsible for consulting local, county and state building codes for securing any necessary building permits before construction. NOTE: Construction codes vary from locality to locality.
NOTE: Dimensions are to the finished surfaces. Grill cavity surfaces are to be plumb and level to ensure a proper fit.
HARDWARE COMPONENTS
INSTALLATION RECOMMENDATIONS
DEDICATED ELECTRICAL CIRCUIT WITH GFCI PROTECTED OUTLET
A dedicated GFCI protected electrical circuit is required for all Memphis Wood
Fire Grills and controller systems. This circuit should be installed by a
Certified Electrician. Although the Memphis Grill only uses about 4 amps of
current during startup, any other equipment (refrigerator, pool pump,
fountains, ect.) that have high current draw, consistently or intermittently
from the same electrical circuit can cause potential issues and/ or
interruptions with the performance of the grill. We recommend an on/off switch
to be installed in this circuit so that the grill can be easily disconnected
from power when not in operation. This will prevent the buildup of
interference that could affect the controller’s operation.
INSTALLATION STEP 1: UNPACKING
Grill requires (2) two people for safe assembly
Please note that during shipping some movement may have taken place, so a
complete visual
inspection is required. Be sure to inspect entire grill after removing the
protective shipping carton. Report any damage to your local dealer
immediately. Shipping damage is not covered under warranty. Some surfaces may
be sharp so wear gloves when assembling. Do not plug in the grill until it’s
fully assembled, the plastic protective film is removed from all stainless
steel surfaces, and you’re ready to cook. See: “startup procedure” for more
details.
INSTALLATION STEP 2: WIRING
INSTALLATION STEP 3: BRACKETS
INSTALLATION STEP 4: GRILL MOUNTING
INSTALLATION STEP 5: CONTROLLER BOX INSTALL
INSTALLATION STEP 6: FINAL ASSEMBLY
Refer to page 5 for item part numbers, descriptions and quantities
28) Insert the three ash/grease drawers back into the unit.
29) Place Savorizer (item 2) onto the left and right lower brackets found
inside the unit.
30) Place the four lower cook grates (item 1) onto the front and rear
supports. Place the
long cook grate (item 1) onto the left and right upper brackets found inside
the unit.
Vent holes on the mounting brackets must remain unobstructed.
Refer to the manual for first time use instructions.
MEMPHIS PRO BUILT-IN COMPONENT WIRING DIAGRAM
NOTE: ALL TWO WIRE PAIRS FOR A SPECIFIC COMPONENT ARE REVERSABLE
Example: The auger motor wiring can have the either spade connector from its
two wire pair attached to either terminal and the motor will function
normally.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>