bioBidet LW-1000 Luxury Bidet Seat Owner’s Manual

bioBidet LW-1000 Luxury Bidet Seat

NOTES:

• This product should be installed according to this manual.
• Please read this manual carefully and install properly.
• Please save this manual and place at an easily accessible location.
• Do not attempt to service this appliance yourself. Doing so could void the warranty.

IMPORTANT SAFEGUARDS

• When using electrical products, Basic electrical safety precautions should always be followed.
• READ ALL INSTRUCTIONS BEFORE USING
•  For use with 120V 60Hz: Power supply must be a 15 Amp GFCI outlet.
•  The electrical cord must be connected to a GFCI outlet.
•  The GFCI outlet should be 1ft. above the floor.
•  Install only in well-ventilated areas to avoid excess humidity.
•  Do not install in narrow toilet stalls or in shower stalls.
•  Install only where direct contact with water is minimized.
•  Do not install near any heat source.
•  Avoid using extension cords if possible. Consult with a certified electrician where extension cords are necessary.
• ANGER – To reduce the risk of electrocution:
•  Do not use while bathing.
•  Do not place or store product where it can fall or be pulled into a tub or sink.
•  Do not place in or drop into water or other liquid.
•  Do not reach for a product that has fallen into water. Unplug immediately.
• WARNING- To reduce the risk of burns, electrocution, fire, or injury to persons:
•  Close supervision is necessary when this product is used by, on, or near children.
•  Use this product only for its intended use as described in this manual. Only use attachments recommended by the manufacturer.
•  Never operate this product if it has a damaged cord or plug, if it is not working properly, has been dropped or damaged, or dipped into water.
• Return the product to a service center for examination and repair.
•  Keep the cord away from heated surfaces.
•  Never drop or insert any object into any opening or hose.
•  Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
•  Connect this product to a properly grounded outlet only. See grounding instructions.
•  Unplug this product before filling. Fill (reservoir) with water only.

GROUNDING INSTRUCTIONS

• DANGER- Improper use of the grounding plug can result in a risk of electric shock.
•  This product has a three-prong grounding plug, which must be plugged into an outlet that is properly installed and grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat blade terminal. The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire. Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the product is properly grounded.
•  This product is for use on a nominal 120V circuit, and has a grounding plug that looks like the plug illustrated in sketch A in Figure 1. A temporary adapter, which looks like the adapter illustrated in sketches B and C, may be used to connect this plug to a 2-pole receptacle as shown in sketch B if a properly grounded outlet is not available.
•  The temporary adapter should be used only until a properly grounded outlet (sketch A) can be installed by a qualified electrician. The green colored rigid ear, lug, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used,  it must be held in place by a screw

Optional Grounding Instructions

MAIN UNIT & PARTS

REMOTE CONTROL

DIMENSIONS

INSTALLATION

1. Remove the seat from the existing toilet body.
   • Release the nuts, and then remove the seat and cover from it.
   • Store the seat in a proper place for future use.
   • Turn off the water and flush the toilet.
2. Install the T-valve.
   • Disconnect the existing water hose.
   • Attach the T-valve to the bottom of the toilet.
   • Ensure the rubber washer is properly seated and attach the original water hose to the T-valve
3. Fix the catch plate onto the toilet.
   • Place the catch plate on the toilet with the arrows pointing towards the toilet tank.
   • Align the bolts guides over the toilet bolt holes.
   • Secure the catch plate to the toilet by hand tightening the bolts.
4. Push the main body towards the catch plate completely
   • Push it until you hear a “click.”
   • When the product is not installed well, it may cause leakage.
   • Adjust as needed before tightening bolts. Do not over tighten bolts
5. After installing the T-valve, connect the supplied bidet hose from the center of the T-valve to the bidet.
6. Turn on the water and check for leak
7. Plug in and be sure that the nozzle comes out and retracts when powered on.

Using inline carbon filter

Use of external water filter is only recommended in areas with known hard water issues. If a filter is used, it must be replaced every 3 months. This product is designed and intended for use exclusively with Bio Bidet DIB water filters. The purchase or use of any other water filter is not the responsibility of BBC Innovation LLC. As such, any use of non-DIB water filters is prohibited and will void the warranty for those Bio Bidet products. Bio Bidet will not be responsible for any resulting damages or claims related to the misuse or distribution of non Bio Bidet DIB filters.

OPERATION

1.  Sit on the toilet seat
2.  Wash, Bidet, Turbo
3.  Dry Temperature Control
4.  Pulse
5.  Child Function
6.  Nozzle Position Control
7.  Water Pressure Control
8.  Stop
9.  Seat/Water Temperature Control
10.  Energy Saving Function
11.  Nozzle Cleaning
12. .Night Light
13. .Automatic Tank Draining
14.  Sitz Bath
15. .Seat Sensor Bypass
16.  Reset

MAINTENANCE & CLEANING

1.  Screen Filter Cleaning
2.  Seat Cleaning
3.  Extended Non-Use
4.  Draining of Tank

TROUBLESHOOTING GUIDE

Puls

than 3 seconds.

| Seat sensor feature will be deactivated| OFF
4| Night Light| | “+” for longer than 3 seconds.| To turn on/off the night light.| ON
5| Factory reset| | Press and hold the Stop button for 5 seconds.| After 3 seconds, the seat will power off. Keep holding another 2 seconds and the seat will power back on.

This completes the factory reset process.

| ON
6| Automatic tank draining| | “    ” and “ ” for longer than 3 seconds.| Automatic tank draining feature will be deactivated.| OFF
Problem| Check List
---|---
Completely out of order.| •     Check if the power plug is not connected.

•     Check if the power supply or outlet has failed.

Water does not spray out.| •     Check if the water supply is turned on.

•     Check if the water valve is open.

•     Check if the nozzle is blocked by foreign material.

•     Check if connection hose is bent.

Water pressure is low.| •     Check if screen filter is blocked and clean if needed.

•     Check if the water pressure is set at too low level.

Water is not warm enough.| •          Check if its temperature is set at off or low level, or economy mode.
Seat is not warm enough.| •          Check if its temperature is set at off or low level, or economy mode.
Water tank is drained intermittently.| •     Check if the automatic water draining feature activates.
No.| Self Diagnosis| Indication
---|---|---
1| Water temp sensor is disconnected or not inserted| LEDs of water low + middle level blinking
2| Water temp sensor is short- circuited or overheated| LEDs of water high + middle level blinking
3| Seat temp sensor is disconnected or not inserted| LEDs of water low level blinking
4| Seat temp sensor is short- circuited or overheated| LED of water high level blinking

SPECIFICATIONS

WARRANTY

• We hereby guarantee the product as follows in accordance with the regulation of consumer damage compensation.

•  In case of product failure, please contact Bio Bidet

• Product warranty will be effective for one year from the date of purchase.
  Regarding Product Warranty Regulation

• We will repair the product free of charge in case it fails under normal operating circumstances in accordance with the user guide during the warranty period.

• Although it is within the warranty period, we will charge the repair service fee etc. (repair + parts + travel expense) if it falls under the following cases:
  Voiding Warranty

• Defects occurred from the user’s careless handling

• Defects occurred from usage with incorrect power voltage (E.g. 220V was used to the 110V product.)

• Defects occurred from Force Majeure (fire, salt, flood, etc.)

• Failure or damage due to mishandling during operation after installed.

• Defect occurred from interior modification at user’s discretion

References

• Bio Bidet by Bemis - Bidet Seats, Attachments, Smart Toilets

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>