Cloud CVS-C5 Series In Ceiling Loudspeakers Installation Guide
- June 13, 2024
- CLOUD
Table of Contents
CVS Series
In-Ceiling Loudspeakers
CVS-C5 Series In Ceiling Loudspeakers
Models
CVS-C5, CVS-C5T, CVS-C52T, CVS-C53T,
CVS-C62T, CVS-C82T, CVS-C83T
Installation Guide
CAUTION – Installation
Speaker must be installed by a qualified speaker technician.
CAUTION – Servicing
The unit contains no user-serviceable parts. Refer servicing to qualified
personnel.
Do not perform servicing unless you are qualified to do so.
CAUTION – Tap Settings
Before use, check that the transformer is set to the correct power tapping for
the system.
INFORMATION
Model| Rated power| Max Power| Cut-out diameter|
Depth required above ceiling| Line transformer power tapping’s
(100 V-line) or impedance
---|---|---|---|---|---
CVS-C5| 10 W| 20 W| 169 mm (6.65″)| 65 mm (2.56″)| 16 ohms
CVS-C5T| 10 W| 20 W| 169 mm (6.65″)| 65 mm (2.56″)| 6 W / 3 W / 1.5 W / 8 ohms
CVS-C52T| 20 W| 40 W| 169 mm (6.65″)| 65 mm (2.56″)| 6 W / 3 W / 1.5 W / 8
ohms
CVS-C53T| 20 W| 40 W| 169 mm (6.65″)| 65 mm (2.56″)| 24 W / 12 W / 6 W / 8
ohms
CVS-C62T| 25 W| 50 W| 205 mm (8.07″)| 105 mm (4.13″)| 24 W / 12 W / 6 W / 8
ohms
CVS-C82T| 25 W| 50 W| 241 mm (9.49″)| 92 mm (3.62″)| 24 W / 12 W / 6 W / 8
ohms
CVS-C83T| 25 W| 50 W| 248 mm (9.76″)| 110 mm (4.33″)| 24 W / 12 W / 6 W / 8
ohms
Note: all model numbers are suffixed either ‘B’ or ‘W’. This refers to
the colour of the finish: ‘B’ = black, ‘W’ = white.
All models have integral front grilles, with the exception of Models CVS-62T
and CVS-83T, which have removable front grilles.
Cut a hole at the mounting location in the ceiling using the template
supplied. You can check that the diameter is correct for the model by
referring to the table above.
Double check that there are no cables or other obstructions behind the
mounting surface before making the cut-out.
Strip the ends of the wires coming from the amplifier and insert in the
spring-loaded terminal block connector on the loudspeaker. No screwdriver is
required.
The correct power tapping is chosen by connecting to the appropriate terminals
of the connector. A description of the power tap selection is shown on the
magnet sticker on the rear side of the loudspeaker.
When using 100/70/25 V speakers in low impedance mode (8Ω), disconnect the
ground wires by interrupting the cable lugs.
Make sure the mounting clamps are fully bent inwards, allowing the speaker fit through the cut-out. Insert the speaker to the opening.
Fix the speaker in the provided opening by tightening the screws of the
mounting clamps using a screwdriver. A quarter turn will cause the mounting
clamps to flip-out, locking the speaker in place.
Tighten the screws further until the speaker unit is fully secure.
To attach the grill to the speaker, insert the lips into the provided openings on the speaker baffle and rotate it a partial turn (15°) to lock it into place.
The speaker is now correctly installed and ready for use.
CVS Series Installation Guide V1.0
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>