NETTA 103091 7.2V Grass Shear and Hedge Trimmer with Pole User Manual

NETTA 103091 7.2V Grass Shear and Hedge Trimmer with Pole

SAFETY & WARNINGS…

INTENDED USE
This product has been designed to trim hedges, shrubs, and grass in residential gardens. It is not for use in public parks, sports grounds, agriculture, or forestry. Failure to use this product as intended will void the warranty.

REGULAR CHECKUPS

• Check cables every time before plugging into a socket, make sure power cables are not burst or snapped and that the powerplug has no damage.
• Check all the knobs are functioning correctly.

GENERAL CAUTIONS

• Always follow this instruction manual and go through all the 7safety checks.
• This is not toy – do not let children play with it.
• DO NOT modify this product in any way.
• Keep work areas clean and well lit.
• Do not operate tools in explosive atmospheres.
• Before using an electric-powered appliance, check the rating label and voltage information on this manual, or the rating label on back of the machine.
• Always connect the device to a socket with Residual Current Device (RCD) fitted with your home circuits.
• If you are unsure, please seek a certified election for advice.
• The appliance must not be immersed in liquid.
• Do not use power tools in wet or damp conditions.
• Do not overload your power tools. Match each tool to the task.
• Do not use any power tool if the on/off switch is damaged.
• Check that the moving parts of your tool operate smoothly and are not cracked or damaged.

RISK OF PERSONAL INJURY

PRODUCT OVERVIEW

1. Extension Pole
2. Safety Switch Block (Extension Rod)
3. Switch (Extension Rod)
4. Machine Frame
5. Lock Sleeve
6. Rotate & Lock Button

NOTE: PLEASE PULL OUT THE SAFETY LOCK (8) BEFORE CHANGING BLADES.

Assembly Instructions

OPERATING THE PRODUCT

Assembly Instructions

1. To install or replace the blade, place the device on a hard surface. Turn the device upside down with one hand gently push the blade shield down with the other hand. Then gently move the blade shield (Photo. 3)
2. Gently remove the blade by raising the tip of the device blade.
3. Insert the required blade into the engine housing (photo. 5)
4. Align the center-edge tooth roll with the gear in the centre of the device so that the blade lies flat on the housing and an appropriate fit is ensured (Photo. 6)
5. When the blade is in the appropriate position, the blade shield can be replaced (photo. 7)
6. Move the blade shield forward until it jumps to its place and shoots. The device is then ready to use (photo. 8)

Installation of the extension pole and operation

Warning! The extension pole can only be used with the blade of the grass shear. It should not be used with the hedge trimmer blade. The extension pole has been designed for convenient and comfortable lawn moving in difficult places and/or to stop you bending over.

1. Attach the extension pole to the device
2. The user should hear a characteristic click sound suggesting the correct installation of the device with the extension pole.

Working Height Setting

You can adjust the working height of the extension pole from 60cm to 100cm.

1. Turn the lower part of the height adjustment lock sleeve clockwise until the moment of release.
2. Set the working height of the extension pole.
3. Turn the lower part of the height adjustment lock sleeve anticlockwise until it locks.

Turnover Function
The device on the extension pole can rotate in three positions (- 790/0/+90). Pull the blocking mechanism (pictured below) and adjust the devices’ angle to the desired position until you hear the characteristic click sound.

USE AND MAINTENANCE

• Disconnect the charger plug from the power source before making any adjustments, changing accessories, or storing the tools.
• Check for misalignment or binding of moving parts, breakage of parts and any condition that may affect the tools operation.
• Use this 7.2V lithium-ion cordless Grass and Hedge Trimmer in accordance with the instructions.
• Do not allow people unfamiliar with this tool to operate it.
• Do not overwork/force the tool.
• Do not use the tool is the switch does not turn it on or off.
• Store idle tools out of reach of children and other untrained people.
• Maintain this tool with care.
• Hold the tool by the insulated gripping surfaces to prevent accidents.

Charging and Recharging the Unit

• Before charging the unit with the AC charger, make sure that the tool is turned off.
• This tool can only be charged using the supplied charger.
• Never recharge the unit outside.
• Do not store this tool or its charger in temperatures below 0°C or above 40°C
• Do not use a damaged charger.
• Never pull by the cord. Always pull the plug when disconnecting.
• Ensure the cord is not a trip hazard and does not get damaged.
• Never open this tool. There are no customer-serviceable parts inside.
• Never attempt to open or modify the battery for any reason.
• Never incinerate the battery or device when they are ready to be discarded.

Before Starting Work
Before first use, fully charge the battery. Use only the original charger included in the set. When charging, one red LED light will be on – the remaining LEDs will be off.

1. Connect the power cord plug with the charger into the charging jack.
2. Plug the charger into an AC outlet. Make sure that the voltage of the electrical outlet is compatible with technical requirements.
3. When charging, the red LED will be on.
4. The recommended charging time is 5 hours and 30 minutes (for a completely discharged battery). The battery is fully charged when  green LEDs are on. Your tool is then ready to use.
5. Once charged, first remove the charger from an AC outlet and then unplug the charger from the charging socket.

Caution! When charging, the handle of the device may heat up. This is normal. Please wait until the handle cools down before using the device.

Switching On and Off

1. To switch the tool on, slide the lock-off button and push the on/off button at the same time.
2. Release the lock-off button.
3. To switch the tool off, release the on/off switch. Once switched off, the blades will keep moving for some time. Wait until the blades stop completely. Do not touch moving blades and do not try and stop them.

Operating

• Hold the tool away from you. Stand in a safe and stable position.
• When cutting, ensure blades do not come into contact with objects i.e. wires, metal parts, stones, etc. as this may damage the mechanisms.
• If the blade is blocked by a foreign object, immediately turn off the tool.
• Clean the tool after each use. Remove the material left on the blades only when the tool is turned off. Take extreme care.
• Follow the instructions concerning the maintenance and cleaning of the device.

Trimming Shrubs and Hedges

• Make sure to cut stems up to 7.5mm/0.29” thick.
• When trimming the hedge, evenly move the tool along the cutting line so that stems get directly into the blades.
• The double-sided cutting part of the blade allows to trim in both directions.
• After finishing the task, place the cover on the blades.

Shearing Grass

• Move the grass shears along the lawn edge – do not allow the blade to come into contact with hardened surfaces or stones.
• After finishing the task, place the cover on the blades.

CLEANING & STORAGE

Cleaning

• Proper and regular cleaning ensures safe use and extends the tools’ life.
• To avoid electric shock or burns, switch off the tool and allow it to cool down before performing cleaning and maintenance.
• Before each use, inspect the device for obvious defects. Ensure the covered and guards are undamaged and correctly fitted.
• Clean the tool with a dry cloth or blow it with compressed air.
• Carefully clean the blades after each use. Rub the blades with a cloth soaked in oil or spray them with a metal spray.
• Blunt bent or damaged blades must be replaced. Only use original spare parts.
• Store the blades in the cover.
• It is recommended to clean the tool immediately after each use.
• Ensure water does not get inside the tool.
• Do not use any cleaning alkaline, abrasive, or disinfectant chemicals as they may adversely affect the surface of the tool.

Repair

• This tool contains no user-serviceable parts. Do not repair the tool yourself. See the spare parts/repair section on the next page.

Storage

• Clean the tool in accordance with the instructions.
• Always store the tool in a dry, aired location out of reach of children.
• Protect the tool against vibrations and shock during transport.

SPARE PARTS/REPAIR

We hope our products will last as long as possible to reduce the buildup of electrical waste in the world. If any consumable parts need replacing, please check our website for stock availability and purchase. If our website does not have the parts listed, but you still need consumable parts, please contact our customer support to check availability and process your order.
To order replacement parts, please go to www.nettadirect.com/parts. You will need PDC information from your product, user manual or carton box. Alternatively, go to our website and use search bar to find the parts available.
You can also find this code on the back of this User Manual. For our Repair Service, please contact our customer support with email on support@nettadirect.com they will provide with more details of repair service with NETTA.

DISPOSAL OF PRODUCT

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.

DISPOSAL: Please dispose of this product responsibly. This item cannot be disposed of with general waste. Please contact your local council authority for more information on how to dispose this product. If this product is disposed of with general waste, it will end up in a landfill and will leak hazardous substances into the groundwater – effecting our food chain.

YOUR WARRANTY

If you purchased with NETTADIRECT, or one of our authorised resellers, you will automatically enrol your warranty for 1 (ONE) year. You do not need to register again for your warranty. All warranties will be carried out our terms and conditions include warranty conditions you will find out from our website at  www.nettadirect.com.
PLEASE NOTE: Consumable parts will not be covered by warranty. If a consumable part needs replacing, you need purchase separately from our website. Please quote with your original proof of purchase (invoice) and name or delivery address, postcode, so we can locate you when you contact us for warranty.

COPYRIGHTS

NETTA and its logo including images and contents in this manual and website is copyrighted. All intellectual property rights belong to NETTA owner CONSUMABLE DIRECT LIMITED. ANY UNAUTHORISED USE, MODIFICATION or DISTRIBUTION of the NETTA logo, website image, and its contents (from website, manuals) will violate worldwide copyright, trademark and associated laws. We reserve the right to proceed with lawsuits to anyone who is found breaching our copyrights policy. For more details, please check our website copyright policy for more information.

References

• NETTA Official Website | www.nettadirect.com | FREE U.K. Delivery
• NETTA Official Website | www.nettadirect.com | FREE U.K. Delivery

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>