NETTA Electric Glass Panel Heater Instruction Manual
- June 8, 2024
- NETTA
Table of Contents
NETTA Electric Glass Panel Heater
Safety Instructions
- Read the manual before you use the Keep the manual and ensure it stays with the heater if you give it to a new owner.
- Before use, check that the heater and all supplied accessories are complete and
- You must install the heater according to the installation You must plug the heater into a socket that meets the following requirements: AC 230V, frequency 50/60Hz.
- The heater is only suitable for indoor Do not use it outdoors.
- Do not leave the heater unattended during Keep the heater out of the reach of children to avoid the risk of burns.
- Do not use an external controller with the The heater must not be on “ON” when it is not in use.
- Do not use the heater near flammable or explosive materials to avoid the risk of fire or explosion.
- Inserting items into the protective grill of the heater is strictly prohibited to avoid the risk of electric shock.
- Do not touch the metal housing as it will get hot when the heater is in use to avoid the risk of Set aside time to let the heater cool before turning it OFF and storing it.
- Unplug the heater if it is going to be out of use for a long
- Before using the electric heater, ensure it is in good working condition and Do not plug in or use the heater if the casing, wire, or plug are damaged.
- You may damage the heat if the heater is Check that the component is not damaged before each use. Do not use the heater if the element has broken.
- Disconnect the plug from the socket when moving or cleaning the When disconnecting, first turn OFF the switch, then unplug the plug. Do not wrench the cable.
- Demolition of the electric heater without authorization is strictly prohibited. Please look for professional service personnel if the heater is damaged.
- The product is limited to home use
- During use, do not let bare skin touch the appliance’s surface.
- Do not share the heater’s socket with other appliances to avoid the risk of fire due to excessive load.
- CAUTION: Never cover the heater; there is a risk of fire and overheating when the heater is covered.
- You must not place the heater immediately below an electrical socket outlet.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or a similarly qualified person to avoid a hazard.
- Avoid using an extension cord as this may overheat and cause a fire risk.
- This heater is not suitable for use in bathrooms, laundry areas or locations where there may be moisture. Never place the heater where it may fall into a bathtub or other water receptacle
- Do not use the heater in the immediate surroundings of a bath, shower, or swimming pool.
- Children of less than three years should be kept away unless continuously supervised.
- Children aged three to eight years should only switch ON/OFF the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning the use of the appliance safely and understand the hazards involved. Children aged from three years and less than eight years shall not plug in, regulate, and clean the appliance or perform maintenance.
- This appliance should be used by children aged eight years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given safe supervision or instruction concerning the use of the appliance and understand the hazards involved. Children should not play with the appliance and should not do cleaning and user maintenance without supervision.
- CAUTION: some parts of this product can become very hot and cause burns. Particular attention must be given where children and vulnerable people are present.
Installation Instructions
- Before installing, check that all parts are complete and the product is intact.
- If you want to use the electric heater freestanding, please fit with the feet provided with the heater, following the instructions below. Make sure the heater is mounted on a level, stable and clean surface.
Freestanding Installation
- Put the product upside down on a soft cotton cloth or carpet.
- Fix the feet to the base of the heater using the screws provided. Line up the holes in the base with the holes in the feet, put the screws through the holes, and tighten with a screwdriver.
Wall Mounted Installation
- Take four brackets, six expansion screws and six screws out from the box and fix two brackets onto the wall according to the distances between holes of the bracket, as shown in the picture below.
- Fix two brackets onto the bottom of the product, as shown in the picture below.
- Hold the side of the product, look at the position of the wall hole of the rear cover, and slide the wall to the top of the slot. The wall installation should be completed as shown below.
Note:
Before drilling, ensure no cable or other pipelines are on the wall to avoid
damage. Remember that the screws on the wall should be fixed and firm to
ensure the safe installation of the electric heater on the wall. Please note
the safe distance mentioned below.
- During installation, the heater must maintain a sufficiently safe distance from combustible materials and gas and away from water.
- During wall-hanging installation, keep the installation height from the ground greater than 15 cm. Hanging-type heater shall be no less than 50 cm away from the ceiling.
Using the Heater
Display Screen
- A. Wi-Fi Connection
- B. Working Status –heating if icon displayed, not heating if not displayed
- C. Keyboard Lock
- D. Timer
- E. Comfort Mode
- F. Eco Mode
- G. Anti-Frost Mode
- H. Setting
- I. Up
- J. Down
- K. Power switch/WIFI setting
Heater Control
-
The heater will beep as it powers ON. The heater starts on standby mode, displaying the Wi-Fi icon and the room’s current temperature in °C.
-
To initiate heating, press the ON/OFF button. When first used, you will see the heating icon and the ECO mode icon , Which means the device is in the ECO mode state. The heater has a memory function; when you turn it ON after the first time, it will be in the last working state: or and .
Note: Using the memory function, you can control your heater using your phone worldwide if the network is connected. -
To change the heating mode, press the UP and DOWN to cycle through the ECO , Comfort , and anti-frost modes.
-
To adjust the set temperature of any mode, you can press the setting button. When the digital light flashes, use the UP and DOWN buttons to adjust the temperature. The temperature range is from 5°C –50°C.
Note: You cannot be adjusted the temperature in anti-frost mode. -
To set the timer, press the setting button; when the light flashes , use the UP and DOWN buttons to adjust the time; the timer range is 1 – 24 hours. The digits will flash while in “Setting”, and then the screen will return to heating mode. The timer icon on the screen will show that the timer has been set, and the heater will heat until the time has elapsed.
-
To set the child lock, press and hold the UP button. The padlock icon will appear on the screen, and the control panel will be locked out. To release, press and hold the down button. The padlock icon will disappear, indicating that you can use the buttons again.
-
Long press the setting button to turn off all the display lights and press any key to light up the product’s display screen. After long pressing the setting button, the product enters the low light mode; press the button for 30 seconds to leave the low light mode. In the low light mode, control the product through the APP, and the product will sound!
Connecting to Wi-Fi
-
The first step is downloading the Smart Life app onto your smartphone or tablet to connect your heater to Wi-Fi. You can find the app by scanning the QR code below or searching “SmartLife” in the Google Play or Apple app store
-
Download and install the app. Unless you already have a SmartLife account, you will need to create an account by tapping Register.
The device will automatically determine your country, although you can change this if necessary. Enter your phone number or email address. If you enter a phone number, a verification number will be sent to your phone; enter this number to verify, then create a password. You will need to create a password if you enter your email address. -
To add your heater to the app, first put the heater in Wi-Fi connection mode. The heater is in Wi-Fi connection mode when the Wi-Fi icon is flashing. If the Wi-Fi icon is not flashing, go to standby mode and hold down the button for three seconds
-
Once the icon flashes, go to the app and press Add a Device. Select the device type (Small Appliances > Heater) and confirm that the indicator is flashing. You will then be prompted to enter your Wi-Fi password, allowing the app to find your heater using your Wi-Fi.
-
The app will then display its connecting screen.
NOTE: if the heater is failing to connect, press and hold the button for three further seconds. It will then switch to its second connection mode. The heater has two connection modes: one is the icon flashes slowly (once per second) and one where the icon flashes fast (three times per second). Most devices will connect on the fast-flashing mode -
The heater will beep and display a solid icon when the device is connected. The app will confirm that the heater has been added. You can now name the device, share it with family members, or proceed to schedule your heating
Using the Smart Life App
You can use the app to control multiple devices. You will see the status of your device as shown on the device list:
- Offline (the device is turned OFF at the wall/rocker switch)
- Turned OFF (the device is in standby mode)
- Turned ON (the device is in heating mode)
- When the heater is online, tap the device name to go to the control interface
Note: When the heater is offline, you will not be able to control it with the app.
Controlling the Heater
You can change the heater’s current mode by tapping the mode buttons. You can adjust the mode’s temperature using the + and – buttons when you are on that mode.
Scheduling your Heating
You can program your heating by creating a schedule of “events” where the heater switches ON or OFF. These events can be temporary, like setting a timer or recurring, so the heater switches on at the same time every week. You can select an unlimited number of events, switching the heater on and off across the week
For every event, you must set a start time. Then, choose whether you want it to repeat. Select “Only Once” if you wish to set a timer for now. If you want the event to repeat, select which days you want it to occur. Finally, choose whether you want the heater to switch ON or OFF. Make sure you confirm your settings at every stage and press save to keep the event. Each event will appear in your schedule. You can activate and de-activate events using the toggle and delete events by swiping left and tapping Delete.
The heater will beep when it begins a new heating event and will heat at
whatever mode it was last set to.
Note:
- You cannot schedule mode changes.
- If you change the heater’s setting during an event – i.e., turning it ON when it is scheduled to be OFF – the heater will remain as it is until the next scheduled event.
Smart Features
The “Smart” section of the SmartLife app allows you to add functions that make your heating easier and more intuitive to control. You can reach the Smart section by pressing the Smart icon at the bottom of the app.
Scenarios
Scenarios are customizable commands that combine your devices to perform set actions. They appear as shortcuts on the app, which you can trigger by tapping the image, offering a quick and easy means of coordinating your heating. For example, you could create a “Heat Boost” scenario, which at one tap switches all your panel heaters ON, at high power mode, at 30 °C. To create new scenarios, press the + button while on the Scenario screen. You can add as many heaters as you want to a “scenario”. You can control whether they switch ON or OFF, what mode they run on, and what temperature they are set to. You can add any device controlled by the SmartLife app to a scenario.
Automation
Automation allows you to set up actions that are triggered by external events. Triggers include the weather, temperature, humidity, sunset, sunrise, and your location. You can add multiple actions and multiple triggers for each automation event, so you could, for example, set all your heaters to come on at 21 °C if you arrive home when it’s snowing! To create new scenarios, press the button while on the Scenario screen
Voice integration
SmartLife is compatible with both Amazon Alexa and Google Home. First,
download the SmartLife skill onto your Alexa or Google Home app to connect.
Note: You can link your Alexa or Google Home app with your SmartLife app.
Depending on your device, your voice control app may discover your device
automatically, or you may need to prompt it to do so Once the SmartLife skill
is enabled and linked with your SmartLife app, you should get notifications
whenever you add a new heater or scenario. The notification will tell you what
to say to control the heater or “Scenario” by voice. You can find quick guides
to connecting the app to Google Home and Alexa in the FAQ section. Press then
Example commands:
- OK Google, turn on Glass Heater
- Alexa, switch off Glass Heater
- OK Google, switch Glass Heater to 25 degrees
- Alexa, set Glass Heater to 9 degrees
- OK Google, turn on Comfort
- Where Glass Heater is what you’ve named the heater in the martLife app
- Where Comfort is the name of a scenario created in the SmartLife app.
Sharing
You can share control of your devices with family members. Go to , select
“Family Management”, and select “Add Member”. Add your new family member’s
email address or phone number to send an invitation.
Note: You can only share numbers and email addresses connected to app-
compatible devices such as smartphones or tablets.
When you add new members, you can choose whether to set them as an administrator. Members added as administrators will have all family permissions, including the facility to delete the family. Members not set to administrator can control scenarios and devices but cannot add or remove them.
FAQs
Find the answer to many troubleshooting problems in the app’s FAQ. To access the FAQ, press then select
Technical Data
Product Specification
- Model No: GPH-20DA
- Voltage: 230V
- Frequency: 50/60Hz
- Power: 2000W
- Category: I
ERP Label
The product is for household use only
Cleaning and Care
Maintenance
Always disconnect the appliance and let it completely cool before any maintenance. Use a vacuum cleaner to remove dust on grilles. Clean the outside of the unit with a damp cloth and then dry it with a dry cloth. Never immerse the unit in water, nor let water drip into the unit
Storing
When you disconnect the appliance, let it completely cool and clean it before storing. If you do not use the device for a long period, put the unit and instruction manual back in the original carton and store them in a dry and ventilated place. Do not place heavy items on the carton during storage, as this may damage the appliance.
Hints on Disposal
According to the European waste regulation, 2012/19/EU, this symbol on the product or its packaging indicates that this product may not be treated as household waste. Instead, you should take it to the appropriate collection point to recycle electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. Please contact your local council or your household waste disposal service for more detailed information about recycling this product.
Declaration of conformity
This product conforms to the following European Directives:
- 2014/30/EU (EMC)
- 2014/35/EU (LVD)
- 2011/65/EU (RoHS)
- 2009/125/EC (ErP) + Regulation (EU)
- 2015/1188
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>