FotodioX 600 Pro Warrior Daylight LED Light Kit User Manual

FotodioX 600 Pro Warrior Daylight LED Light Kit

Characteristics

1. The Warrior 600Nlarrior 600X feature high-power C O B LEDs with a lifespan of up to 50,000 hours. These LEDs have a standardized color temperature with a CRI & TLCI c:95 and feature less than 2% illumination decay less over 6000 hours working time.
2. Built-in N T C temperature detection to automatically control the fan and prevent overheating to ensure a long product life.
3. Dimmable from 0-100% and flicker-free due the P W M integrated design.
4. pre-installed special effect modes to help you create the perfect scene. Brightness and speed are adjustable in each mode. Color temperature is also adjustable on the Warrior 600X.
5. Optional battery power via v-lock battery mounts on control box.
6. Firrnware upgrade via USB.
7. Available control options: control box, O M X console, remote control, o r mobile phone APP
8. Use any Bowens mount accessory, such as the Included custom designed standard reflector.
9. Solid aluminum shell provides durability and enhanced heat dissipation for a long product life.
10. 360°adjustable, all metal U-bracket featuring disc brake locking function for safely mounting and achieving any angle needed.
11. LED heat prevention technology ensures that your light will emit steady and accurate light under varying conditions.
12. The LCD displays real-time data.
13. Suitable for indoor or outdoor photography and videography. Great for studio or location shoots including TY, film, portrait photography and more.

Warnings:

1. ALWAYS remove the protective cover before using your light.
2. ALWAYS press accessory lock button on the bottom of the light when removing accessories such as the standard reflector, barn doors or optional zoom lens. Failure to do so my damage your light.
3. During use, avoid dirt or debris from contacting the surface of the C O B LED to prevent damage to the light.
4. HOT! D O N O T T O U C H ! Keep flammable substances at least 4 inches( I 00mm) away from the surface of the LED.
5. Do not block the heat dissipation vents on light body. Blocking these will inhibit airflow, causing the unit to overheat and stop working. This may shorten the lifespan of the light.
6. Do not operate with wet hands, doing so may cause electric shock.
7. Do not operate in environments near flammable gases or volatile liquids as this may increase the risk of explosion/fire.
8. Do not operate in enclosed spaces where heat buildup can be extreme, such as a car on a sunny day. The increased heat will trig ger the auto heat protection function and affect use. Frequent overheating may cause premature failure of the light unit.
9. Do not damage, disassemble, twist or modify the power cord as it may increase the risk of fire or electric shock.
10. Do not place under heavy objects.
11. Keep the light surface clean with a soft, dry cloth. If build-up is noticeable, use isopropyl alcohol on a soft, clean cloth to gently remove debris. Ensure the LED is off and cool, then wipe gently W I T H O U T pressing on the surface of the C O B LED.
12. ONLY use the power control box provided with this product. Should you need a replacement, please contact us.
13. Avoid impact to the L C D screen; impact may damage it.
14. ALWAYS use the safety cable when hanging the fixture.
15. When using the accessories, please ensure that they are properly and securely installed. Improperly installed accessories may fall and become damaged.

Packing List

Warrior 600Nlarrior 600X

1. Protective cover – I P C
2. Power control box – I P C
3. O M X cable – I P C
4. A C Power cable – I P C
5. Safety cable – I P C
6. Custom fit case – I P C

Optional accessories

Parts Diagram(light)

1. Bowens mount
2. Bowens mount accessory lock button
3. Angle adjustment & locking handle
4. D C power input socket
5. Integrated carrying handle
6. U-type bracket
7. Stand mount locking screw

1. Power control box handle
2. Menu buttons
3. Multi-function interface dial/button
4. L C D screen
5. V-lock battery plate
6. Fuse
7. Power button
8. ) A C Power input socket
9. CD D C output socket
10. CD USB port
11. D C input socket ( DC36-48V)
12. CD OMX IN socket
13. OMX O U T socket

Menu Buttons

Specifications

Working voltage| AC I00-240v’.DC36-48V| 2m| I5754Lux| 21256Lux| 31444Lux| 25475Lux| 21204Lux
---|---|---|---|---|---|---|---
Cooling system| Heat pipe radiator, Temperature controlled fan| Sm| 1985Lux| 2577Lux| 391 SLux| 3096Lux| 2685Lux
 | 3200K| 4400K| 5600K| 6500K
---|---|---|---|---
e

Im

|

7162Lux

|

9103Lux

|

14005Lux

|

10729Lux

|

9077Lux

2m| 1929Lux| 2467Lux| 37 I3Lux| 29 I0Lux| 2461 Lux
Sm| 378Lux| 485Lux| 735Lux| 568Lux| 481 Lux
IOm| 108Lux| I37Lux| 206Lux| 162Lux| I39Lux

Set up instructions

Removal and installation of protective cover/Bowens mount accessories To remove the protective cover: Press the Bowens mount accessory lock button in the direction of the arrow shown in the figure. While continuing to hold the lock button, turn the protective cover counterclockwise and pull out to remove. To install the protective cover: Align the protective cover with the Bowens mount, insert and turn clockwise until cover securely clicks into place.

NOTE: ALWAYS remove the protective cover before using your light When the light is not in use, install the protective cover to protect the LED surface from dirt or debris.

lnstallation and removal of the standard reflector.

How to set up the light

1. To mount on light support or stud: Loosen the stand mount locking screw by turning counterclockwise. Place the mount on the light stand and secure the stand mount locking screw by turning clockwise. Please ensure the light stand is fully mounted onto the light support and the stand mount locking screw is securely fastened.
2. When mounting to a I I /8″ Gunior) stud, it will be necessary to remove the set screw using an M4 hex wrench.
3. Adjust the light to the desired angle by loosening the angle adjustment and locking handle by turning counterclockwise. Move the light to the desired position, then tighten the angle adjustment and locking handle by turning clockwise.

How to set up the power control box
Use the connecting cable to connect the light body to the power control box, align the dots on the plug and socket, and then insert the plug to the socket To unplug, pull up the collar of the connector to release the locking mechanism and disconnect it by pulling gently away from the device.

Connect the AC power cable to the power control box via the AC power socket, align it with the locking slot as shown in the figure below, and then insert the power plug.
Connect the AC power cable to the external power supply( AC I 00-240V). To remove the AC power cable, press down the spring lock and turn counterclockwise, and gently pull away from the power control box to remove.

NOTE: Remove batteries when using external AC power. Leaving batteries installed may cause damage to the control box or batteries. ALWAYS remove batteries when the light is not in use for extended periods of time.

Operating instructions

Press the power button to power the light ON or OFc

Control via power control box
Menu buttons introduction Warrior 600 menu buttons: Brightness button, FX button, Fan button, Address settngs button, Language button and Multi-function interface dial/button. Warrior 600X menu buttons: Color temperature button, FX button, Fan button, Address setting button, Language button and Multi-function interface dial/button.

1ntensity (Brightness) and CCT(color temperature) button operation
Warrior 600: Press the intensity button, then turn the multi-function interface dial to increase or decrease the brightness of the light. Brightness is adjustable from 0-100%.
Warrior 600X: Press the CCT button, then press the multi-function interface button to switch between brightness and color temperature, tum the multi- function interface dial to adjust the brightness between I 0- I 00%, and the color temperature between 2700K-6500K.

FX button ( Special effect button)
Warrior 600: Press the FX button, then press the multi-function interface button to switch between INT(brightness), mode and speed. Turn the multi- functional interface dial to control the brightness 0-100%, special effect and speed. The special effect mode includes lightning, fireworks,flash, breath, cop car, SOS, fault bulb, turn signal, tracing, screen, H&L beam. Warrior 600X: Press the FX button, then press the multi-function interface button to switch between brightness, color temperature, mode and speed 0- I 00%.Turn the multi-functional interface dial to control the brightness 0-1 00% , color temperature 2700K-6500K, special effect and speed 0-100%. The special effect mode includes lightning, fireworks,flash, breath, cop car, SOS, fault bulb, turn signal, tracing, screen, H&L beam.

DMX button
Press the DMX button, turn the multi-function interface dial to change the address of the fixture. DMX address range is 1-512.

Fan button
Press the fan button, turn the multi-function interface dial to change the speed of the fan between low, medium, high and auto.

Address Settings button
Press the Address Settings button, turn the multi-function interface dial to change APP/remote address between 1-12.

Language button
Press language button, turn the multi-function interface dial to switch system language between English and Chinese.

Fast and slow adjustments
Press the multi-function interface button for 5 seconds or longer to switch between fast and slow adjustments. The indicator at the bottom of the LCD will change between fast and slow to indicate which adjustment mode is active.

Use of Lishuai mobile phone APP
Please search “Lishuai ” on the App store, or you can scan the below QR codes to download the APP for the Android

DMX connection
When using OMX function, connect the OMX cable to the OMX console (see the figure below). Set the OMX address to desired address for control on the OMX console.

DMX control:
Please see below details of OMX address on LCD and corresponding channels on OMX console.

Remote control operating instructions

1. Set the wireless receiving address of the light by following the instructions for APP/remote Address mode. The address can be set from 1-12.
2. Press the Function button to select the first line on the LCD. Move the cursor to the Address setting. Use the Increase button or Decrease button to set the address between 1-12.
3. Ensure that the APP/Remote Address setting on the light and the Address setting on the remote control are the same. The light/lights with the same address setting can now be controlled normally with the remote control.
4. When pressing the Function button, the first line on the LCD is selected. Switch between INT(brightness), FX, OMX setting, Fan, APP/Remote and Lang.(language) modes by using the Increase/Decrease buttons to change the corresponding data.
5. The wireless remote control has a working distance of approximately 65 feet (20 meters)

USB port operation

When the device requires a software upgrade, the upgrade can be applied by connecting a USB flash drive through the USB port. Software upgrades can be found on www.fotodioxpro.com

Upgrade Operation:

1. Download the updates from www.fotodioxpro.com and save to USB flash drive.
2. Remove the dustproof plug from the USB port and insert the USB flash drive loaded with the upgrade program.
3. Press the Power ON/OFF button to turn the power ON. The DATA indicator light will flash.
4. The upgrade will take approximately IO seconds. The upgrade is complete when DATA indicator stops flashing and the Welcome message displays on the LCD.
5. When the upgrade is complete, remove the USB flash drive and replace the dustproof plug.

All Fotodiox products are backed a 24-month limited warranty.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>