Bobtot ET23 Sound Air1 Portable Speaker Instruction Manual
- June 5, 2024
- Bobtot
Table of Contents
Bobtot ET23 Sound Air1 Portable Speaker
Technical specifications
- Wireless version: 5.0
- Transmission distance: 10m
- Output power: 10N
- Frequency effect: 100Hz-10KHz
- Speaker:52mm, 4010W
- Input power: 5V=1A
- Maximum current consumption: 1A
- Audio signal input connector: Standard D3.5mm earphone
- jack (stereophonic)
Components
Button Instructions
- Mode button Short press: switch function, long press: pair two speakers.
- Previous song
- Power button: press on/off, about 3 seconds/time.
- Play/Pause button Short press: play/pause; Double press: call-back(wireless mode) Short press: connect/hang up(call mode) Press 2 seconds: reject(call mode) Long press: exit wireless connection
- Next song
- AUX jack
- USB port
- Type-C charging pot
- TF card jack 10. Volume+ 11. Volume-
Detailed Instructions for Use:
- Wireless Pairing 1.1. Before using wireless pairing, please turn on the Bobtot- Sound Air1 speaker first.
- Turn on your device(Phone, Laptop Etc), search for Bobtot Sound Air1, and connect it.
- Voice Prompts
- There is a voice prompt when turning on/off.
- Remind 3 times when it’s low battery, and turn off after 15s
- Press the button to the maximum volume with a voice prompt, and the minimum volume without a voice prompt.
- Mode Switching The wireless mode is entered by default after power-on. The sequence of mode switching is as follows: Wireless mode-TF card mode-USB mode-AUX mode.
- LED lights Wireless search status: white light flashes quickly, about 0.5 seconds/time; wireless pairing status: white Ilight is always on. Playing status: The white light flashes slowly for about 1.5 seconds/time; Charging status: The red light always on when is charging, and the red light will off when full charge.
- Volume The default volume of the speaker is 70% when it is power on
- Charging Reminders The machine has a built-in overcharge protection circuit, which can be connected to a computer or charger for about four hours for fully charged. The playing time of each battery will vary depending on the volume used.
- No Working Mode It will automatically shut down after 15 minutes when it’s not playing.
Troubleshooting
- Automatic shutdown: when the battery power is low, the battery protection will be turned on automatically, please charge for 4 hours Use later.
- Unable to play music: The music file storage path cannot be recognized by the player. Please store the music file in the r oot directory of the removable device.
- No sound when connected to the computer: the computer interface is connected incorrectly, please select the correct audio output port
- The key does not respond or the function is disordered: try again after shutting down. 5. If the machine is stuck in an abnormal situation, press the r eset button in the AUX jack.
About the Warranty
- We provide a one-year warranty service.
- Man-made damage is not warranted.
- Customer must offer the necessary information(Order ID, Order Platform).
- To redeem the warranty, please email us at [email protected] for further assistance
RF warning for Portable device:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequencyy energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.