Bobtot ET200 Portable Speaker with Microphone User Guide
- June 1, 2024
- Bobtot
Table of Contents
Bobtot ET200 Portable Speaker with Microphone
What’s in the Box
Check to make sure you have everything below.
- A: 1 * ET200 Portable Speaker
- B: 1 * Wireless Microphone
- C: 1 * Type-C USB Charging Cable
- D: 1 * 3.5mm AUX Audio Cable
- E: 1 * Quick Start Guide
Device Overview
- Volume Down
- Light mode
- Previous Button
- Multi-function Button
- Play /Pause
- Next Button
- Power On/Off
- Volume Up
- AUX Jack/Reset Button
- Type-C Charging Port
- USB Input
Charging Your Device
Turn On/Off
BT Connection/Disconnection
Wireless Microphone
Multi-function Mode
Specification
- Output Power: ZOW
- Power Sup p ly: DC SV
- Built-in rechargeable battery
- Speaker Battery: 7.4V/4000mAh
- Microp hone Battery: 3.7V/Z50mAH
- BT with up to 33ft range
- BT/AUX/USB/MIC function
- IPXS Water-resistant, sprayproof
- Wireless Microphone Supported
- Frequency Response: 100Hz-18kHz
Resetting Your Device
If your speaker is not operating properly, you may reset it. To do so, use
a small object – such as a paper clip – to press the button inside the AUX
jack. Press and hold the button for approximately 2 seconds until the speaker
powers off, and then power it on again as usual.
FCC Warming
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 1 S of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Need help?
Customer Care Guide
At our company, we strive to provide exceptional customer care to every one of
our clients, We believe that building strong relationships with our customers
is essential to the success of our business. To help us achieve this goal, we
have put together the following customer care guide.
Time
We understand that our customers’ time is valuable, so we will respond to any
inquiries within Z4 hours.
Feedback
We know that our customers are the heart of our business so we value your
feedback. We encourage you to share your thoughts and ideas with us.
Solutions
If our customers encounter any issues, we will try our best to find a quick
and efficient solution that meets your needs.
Here at Bobtot, we take customer care very seriously. Our customers are our
first priority, and we are committed to providing the highest quality service.
If you have any questions or concerns, please don’t hesitate to reach out to
us.
We will be happy to assist you:
Call or Message: +1 888 572 1718
Email: [email protected]
bobtot.net
Cl2024 B0BT0T // Features and specifications are subject to change and or
improvement without note.