Bobtot SoundAir Outdoor Portable Wireless Speaker User Guide
- June 12, 2024
- Bobtot
Table of Contents
**Bobtot SoundAir Outdoor Portable Wireless Speaker User Guide
**
What’s in the Box
Check to make sure you have everything below.
A: 1SoundAir Portable Speaker
B: 1USB Charging Cable (Type-C)
C: 1*Quick Start Quide
Device Overview
Buttons and Ports
Power/TWS/Mode
Short press to switch mode. Double click to TWS ,conntect or disconnet with
two speakers. Long press and hold to turn the speaker on/off.
Play/Pause/Answer Button
Short press to pause/play the music. Short press to accept an incoming call.
Double click to call back. Long press to reject an incoming call. Long press
to disconnect BT.
Volume Down/Previous Button
Short Press to turn down the volume. Long Press to go to previous song
Volume Up/Next Button
Short Press to turn up the volume. Long Press to go to next song.
Charging Your Device
Plug the included USB type-C cable into the speaker’s charging port, and connect the other end of the cable to a power adapter (not included).Allow approximately 3.5 hours to full charge the battery. When the battery is low and the red light blinks, please charge it.
The indicate light is red color when it’s charging. The red light will be off when it’s full charged.
Note: We recommend using a USB wall adapter with a DC5V=1A output.
Initial Setup
- Once your speaker is fully charged, press and hold the Power button until you hear a voice prompt indicating the device has entered BT paring mode.
- On your smartphone or tablet, search for the BT device named “Bobtot SoundAir” and tap to connect.
- A prompt will play once pairing is successful.
Note:
- When you turn on the speaker but no connection, it will automatically shut down after 10 minutes.
- When you connected the speaker but no playback, it will automatically shut down after 20 minutes.
TWS Sync Mode
- Long press the ” ****” about 2s on both speakers to turn them on, and the blue light flashes.
- Quickly double-click the ” **** ” on any one speaker, a prompt sound “connected”indicates the speakers enter into pairing mode, the indicator light of one speaker turned solid blue.
- On your smartphone or tablet, search for the BT device named “Bobtot SoundAir” and connect it, you could hear the sound “connected” again, which means connect successfully.You can enjoy the music with two speakers together.
Notes: In TWS Mode, turn off one of the speakers, both of them are off. Double-click the ” **** ” button will be disconnected.
Light Status
Blue light flash | In BT pairing or TWS pairing status |
---|---|
Stay blue light | In TWS or BT connection status |
Red light flash | Low battery |
Stay red light | Chargingc |
Red light off | Full charge |
Hands-Free Calling
Volume Down/Previous Button
Short press once to decrease volume.
Volume Up/Next Button
Short press once to increase volume.
Multi-function Button
Short press to acceptan incoming call. Short press again to hang up. Double
click callback in any mode. Long press to reject an incoming call. On calling
status, long press 2s to switch between phone talking or speaker talking.
Resetting Your Device
If your speaker is not operating properly, you may reset it. To do so, press and hold the **** power button for approximately 8s until the speaker powers off, and then power it on again as usual.
Specifications
- Model Name: SoundAir
- Outdoor Portable Wireless Speaker
- Input Power: 5V 1A
- Impedance:4Ω
- Signal to Noise Ratio:≥ 78dB
- IPX7 water-resistant,sprayproof
- Built-in rechargeable battery
- Built-in Mic
- Range 33ft(10m)
- Frequency Response: 200Hz-18KHz
- TWS Sync Mode(Pair 2 of these speakers together)
- Up to 13 hours of playtime (battery life is measure as number of playtime with volume set at50%)
FCC Warming
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolledenvironment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC ID:2AZ43-ET35
Need help?
Customer Care Guide
At our company, we strive to provide exceptional customer care to every one of
our clients. We believe that building strong relationships with our customers
is essential to the success of our business. To help us achieve this goal, we
have put together the following customer care guide.
Time
We understand that our customers’ time is valuable, so we will respond to any
inquiries within 24 hours.
Feedback
We know that our customers are the heart of our business so we value your
feedback. We encourage you to share your thoughts and ideas with us.
Solutions
If our customers encounter any issues, we will try our best to find a quick
and efficient solution that meets your needs.
Here at Bobtot, we take customer care very seriously. Our
customers are our first priority, and we are committed to
providing the highest quality service.
If you have any questions or concerns, please don’t
hesitate to reach out to us.
We will be happy to assist you:
Call or Message: +1 888 572 1718
Email: service@bobtot.net
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>