KLARSTEIN 10029387 Zelda Extractor Range Hood Instruction Manual
- June 5, 2024
- Klarstein
Table of Contents
- KLARSTEIN 10029387 Zelda Extractor Range Hood
- TECHNICAL DATA
- SAFETY INSTRUCTIONS
- Important hints on installation
- INSTALLATION
- INSTALLING A CARBON FILTER (OPTIONAL)
- OPERATION
- LAMP REPLACEMENT
- TROUBLESHOOTING
- PRODUCT DATA SHEET (10031903 | 10029387)
- PRODUCT DATA SHEET (10035411 | 10035412)
- NOTES ON ENVIRONMENTAL PROTECTION
- DISPOSAL CONSIDERATIONS
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
KLARSTEIN 10029387 Zelda Extractor Range Hood
Dear Customer,
Congratulations on purchasing this device. Please read the following
instructions carefully and follow them to prevent possible damages. We assume
no liability for damage caused by disregard of the instructions and improper
use. Scan the QR code to get access to the latest user manual and more product
information.
TECHNICAL DATA
Item number | 10029387, 10031903, 10035411, 10035412 |
---|---|
Power supply | 220-240 V ~ 50/60 Hz |
Note: You can purchase an activated carbon filter separately for this cooker hood under item number 10030727. Please visit our website: www.hifi- tower.co.uk
SAFETY INSTRUCTIONS
- Thank you for purchasing this cooker hood. Please read the instruction manual carefully before you use the cooker hood, and keep it in a safe place.
- The installation work must be carried out by a qualified electrician or competent person. Before you use the cooker hood, make sure that the voltage (V) and the frequency (Hz) indicated on the cooker hood are exactly the same as the voltage and the frequency in your home.
- The manufacturer and the agent will not bear any responsibility for the damage caused by inappropriate installation and usage.
- Children under the age of 8 must not use the cooker hood.
- The appliance is not intended for commercial use, but only for household and similar environments.
- The cooker hood and its filter mesh should be cleaned regularly in order to keep it in good working order.
- Before cleaning, switch the power off at the main supply.
- Clean the cooker hood according to the instruction manual and keep the cooker hood from the danger of burning.
- Prohibit putting the cooker hood by fire.
- If the appliance does not function normally, contact the manufacturer or a specialist company.
- This device may be only used by children 8 years old or older and persons with limited physical, sensory and mental capabilities and / or lack of experience and knowledge, provided that they have been instructed in use of the device by a responsible person who understands the associated risks.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
- If the range hood is used at the same time as appliances burning gas or other fuels, the room must be adequately ventilated.
- Do not flambé under the range hood. Accessible parts may become hot when used with cooking appliances.
Important hints on installation
- The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).
- Regulations concerning the discharge of air have to be fulfilled.
Important notes about the extraction mode
WARNING
Risk of poisoning from exhaust gases sucked back. Never operate the device in
extraction mode simultaneously with an open flue appliance when there is not
adequate airflow guaranteed.Open fl ue combustion equipment (for example, gas,
oil, wood or coal-fi red heaters, tankless water heaters, water heaters) pulls
combustion air from the room and runs it through an exhaust pipe or chimney to
the outside. In the extraction mode, indoor air is removed from the kitchen
and the adjacent rooms – without suffi cient air intake this creates a vacuum.
Toxic gases from the chimney or extraction fl ue can thereby be sucked back
into the living spaces.
- Always ensure that a suffi cient supply of fresh air is guaranteed and that the air can circulate.
- An air supply / extractor box alone does not ensure compliance with the limit value.
Safe operation is only possible when the negative pressure in the room where the appliance is located does not exceed 4 Pa (0.04 mbar). This can be achieved when the air required for combustion can fl ow through openings that are not closable, for example in doors, windows, in conjunction with an air supply / extractor box or through other technical measures. In any case, consult a qualifi ed chimney sweep who can assess the entire ventilation of your house and propose appropriate measures for adequate ventilation. If the hood is used exclusively in the recirculation mode, unrestricted operation is possible.
Important note on disassembly of the device
- Disassembly is similar to installation/assembly in reverse order.
- Take a second person to help you during disassembly to avoid injuries.
INSTALLATION
Preparation
If you have an outlet to the outside, your cooker hood can be connected as
below picture by means of an extraction duct (enamel, aluminium, flexible pipe
or inflammable material with an interior diameter of 150 mm).
- Before installation, turn the unit off and unplug it from the outlet.
- The cooker hood should be placed at a distance of 65~75 cm above the cooking plane for best effect.
Installation (Vent outside)
Note: When the range hood and appliance supplied with energy other than electricity are simultaneously in operation, the negative pressure in the room must be not exceed 4 Pa (4 x 10-5 Bar).
Chimney installation
Drill 3 x 8 mm holes to accommodate the bra- cket. Screw and tighten the bracket onto the wall with the screws & screw plugs provided.Hang the hood on the hook of the bracket.
Put the upper chimney into lower chimney. Then pulling out the upper chimney upwards. Adjust to reach the height required.Sliding the chimney to adjust the chimney height. When the height you required is reached, then hang the fixing hole to the fixing screws as showed in picture.
For Tower chimney hood
By put the inner chimney into upper chimney. Then pulling out the upper chimney upwards. Adjust to reach the height required. Fix the lower chimney with 2 pcs of 4 x 8mm screws.
Sliding the chimney to adjust the chimney height. When the height you required is reached, then fix 2 pcs of 4x8mm screws onto the hole fixing with plate (see arrow) as showed in picture.Drill 2 x 8mm holes to accommodate the plate (see arrow). Screw and tighten the plate II onto the wall with 2 screws provided. Assemble the chimney onto the unit and fix it with 2 screws.
Use 2pcs 4 x 8 mm screws to attach lower and upper chimney together, do not fasten screws too much, make sure upper decorative chimney can be telescopically adjusted after assembled.
- Upper chimney
- Lower chimney attachment
Installation (Vent inside)
If you do not have an outlet to the outside, exhaust pipe is not required and
the installation is similar to the one show in section “Installation (Vent
outside)”.
INSTALLING A CARBON FILTER (OPTIONAL)
Note: You can also purchase an activated carbon filter for this cooker hood under item number 10030727. Please visit our website: www.hifi-tower.co.uk
Activated carbon filter can be used to trap odours.In order to install the activated carbon filter, the grease filter should be detached first. Press the lock and pull it downward.
Plug the activated carbon filter into the unit and turn it in clockwise direction. Repeat the same on the other side. Make sure the filter is securely locked. Otherwise, it would loosen and cause dangerous. When activated carbon filter attached, the suction power will be lower.
OPERATION
Touch Control
- Depress this button to turn on/off the motor.
- Press this button for increasing the speed of the fan.
- Press this button for decreasing the speed of the fan.
- Turn on/off light.
- Fan speed display:
- 1 = low speed
- 2 = medium speed
- 3 = high speed
Booster function (10035411 & 10035412 only)
Press the [+] button once for a long time to set the highest speed. In the
display, [b] flashes for the Booster function. After 5 minutes, the speed
automatically changes to level 3 (high speed).
Quick timer
Press [+] and [-] and hold for 1 second. Digital display will flash and into 5
minutes count down. After 5 minutes motor and light will turn off
automatically and the buzzer will sound for 1 second.
LAMP REPLACEMENT
- Disconnect the light wiring point which is located within the hood, (behind the grease filer).
- Then use a screw driver remove the bulb holders and wiring from the hood. Replace with the same type and rated lamp: LED (max 1.5 W).
TROUBLESHOOTING
Fault | Possible Cause | Solution |
---|---|---|
Light on, but motor does not work. | The leaf blocked. | Get rid of the |
blocking.
The capacitor damaged.| Replace capacitor.
The motor jammed bearing damaged.| Replace motor.
The internal with of motor off or a bad smell from the motor.| Replace motor.
Light does not work, motor does not work.| Light damaged.| Replace lights.
Power cord looses.| Connect the wires as per
the electric diagram.
Shake of the body.| The leaf damaged and causes shaking.| Replace the leaf.
The motor is not tightly
hanged.
| Lock the motor tightly.
The body is not tightly
hanged.
| Fixed the body tightly.
Insufficient suction.| The distance between the body and the gas top too
long.| Readjust the distance.
Too much ventilation from
open doors or windows.
| Choose a new place and
resemble the machine.
PRODUCT DATA SHEET (10031903 | 10029387)
Information according to Regulation (EU) No. 65/2014 Measurement and calculation methods according to EN 61591:1997+A1:2006+A2:20 11+A11:2014+A12:2015
Item number | 10031903, 10029387 |
---|---|
Description | Symbol |
Annual Energy Consumption | AEChood |
Energy Efficiency class | |
Fluid Dynamic Efficiency | FDEhood |
Fluid Dynamic Efficiency class | |
Lighting Efficiency | LEhood |
Lighting Efficiency class | |
Grease Filtering Efficiency | GFEhood |
Grease Filtering Efficiency class |
air flow at minimum and maximum speed in normal use, intensive or boost
excluded| | 358,7 / 600,9| m³/h
air flow at intensive or boost setting| | –| m³/h
airborne acoustical A-weighted sound power emissions at minimum and maximum
speed available in normal use| | 68/72| dB
airborne acoustical A-weighted sound power emissions at intensive or boost
setting| | –| dB
power consumption in off mode| Po| 0,49| W
power consumption in standby
mode
| Ps| 0,44| W
Contact details| Chal-Tec GmbH, Wallstraße 16, 10179, Berlin, Germany
Item number| 10031903, 10029387
---|---
Description| Symbol| Value| Unit
Annual Energy Consumption| AEChood| 54,6| kWh/Jahr
Time increase factor| f| 1,1|
Fluid Dynamic Efficiency| FDEhood| 24,4|
Energy Efficiency Index| EEIhood| 61,6|
Measured air flow rate at best efficiency point| QBEP| 331,8| m³/h
Measured air pressure at best efficiency point| PBEP| 346| Pa
Maximum air flow| Qmax| 600,9| m³/h
Measured electric power input at best efficiency point| WBEP| 130,5| W
Nominal power of the lighting system| WL| 3| W
Average illumination of the lighting
system on the cooking surface
| Emiddle| 108| Lux
Measured power consumption in standby mode| Po| 0,44| W
Measured power consumption
off mode
| Ps| 0,49| W
Sound power level| LWA| 72| dB
Contact details| Chal-Tec GmbH, Wallstraße 16, 10179, Berlin, Germany
PRODUCT DATA SHEET (10035411 | 10035412)
Item number | 10035411, 10035412 |
---|---|
Description | Symbol |
Annual Energy Consumption | AEChood |
Energy Efficiency class | |
Fluid Dynamic Efficiency | FDEhood |
Fluid Dynamic Efficiency class | |
Lighting Efficiency | LEhood |
Lighting Efficiency class | |
Grease Filtering Efficiency | GFEhood |
Grease Filtering Efficiency class |
air flow at minimum and maximum speed in normal use, intensive or boost
excluded| | 265,7 /414,1| m³/h
air flow at intensive or boost setting| | 607,7| m³/h
airborne acoustical A-weighted sound power emissions at minimum and maximum
speed available in normal use| | 47/65| dB
airborne acoustical A-weighted sound power emissions at intensive or boost
setting| | 68| dB
power consumption in off mode| Po| 0,49| W
power consumption in standby
mode
| Ps| 0,44| W
Contact details| Chal-Tec GmbH, Wallstraße 16, 10179, Berlin, Germany
Information according to Regulation (EU) No. 66/2014
Measurement and calculation methods according to EN 61591:1997+A1:2006+A2:20
11+A11:2014+A12:2015
Item number | 10035411, 10035412 |
---|---|
Description | Symbol |
Annual Energy Consumption | AEChood |
Time increase factor | f |
Fluid Dynamic Efficiency | FDEhood |
Energy Efficiency Index | EEIhood |
Measured air flow rate at best efficiency point | QBEP |
Measured air pressure at best efficiency point | PBEP |
Maximum air flow | Qmax |
Measured electric power input at best efficiency point | WBEP |
Nominal power of the lighting system | WL |
Average illumination of the lighting
system on the cooking surface
| Emiddle| 108| Lux
Measured power consumption in standby mode| Po| 0,44| W
Measured power consumption
off mode
| Ps| 0,49| W
Sound power level| LWA| 68| dB
Contact details| Chal-Tec GmbH, Wallstraße 16, 10179, Berlin, Germany
NOTES ON ENVIRONMENTAL PROTECTION
- During cooking, make sure that there is sufficient air supply so that the cooker hood can operate efficiently and with low operating noise.
- Adjust the fan speed to the amount of steam produced during cooking. Use the intensive mode only when necessary. The lower the fan speed, the less energy is consumed.
- If large amounts of steam are produced during cooking, select a higher fan speed in good time. If the cooking steam has already dispersed in the kitchen, the cooker hood Must be operated longer.
- Switch off the cooker hood when you no longer need it.
- Switch off the lighting when you no longer need it.
- Clean the filter at regular intervals and replace it if necessary to increase the effectiveness of the ventilation system and prevent fire hazards.
- Always put the lid on when cooking to reduce cooking steam and condensation.
DISPOSAL CONSIDERATIONS
If there is a legal regulation for the disposal of electricaland electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.
References
- Hifi-Tower | The Online Shop for Electronics, Home & Living
- Klarstein | Your home. Your kitchen. Your style.
- Klarstein | Der Online Shop für Haushaltsgeräte und Home & Living
- Tienda de Electrodomésticos Online | Artículos para el Hogar | Klarstein
- Klarstein | Boutique en ligne d'électroménager à prix imbattable
- Klarstein Elettromestici - Miglior Qualità Prezzo garantita
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>