KLARSTEIN 10030844 Ice Volcano 2G Ice Cube Maker Instruction Manual

ICE VOLCANO 2G

Ice Cube Maker

10030844   10030848   10030849

www.klarstein.com

Dear Customer,

Congratulations on purchasing this equipment. Please read this manual carefully and take care of the following hints to avoid damages. Any failure caused by ignoring the items and cautions mentioned in the instruction manual is not covered by our warranty and any liability. Scan the QR code to get access to the latest user mannual and other information about the product

TECHNICAL DATA

MANUFACTURER & IMPORTER (UK)

Manufacturer:
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.

Importer for Great Britain:
Chal-Tec UK limited
Unit 6 Riverside Business Centre
Brighton Road
Shoreham-by-Sea
BN43 6RE
United Kingdom

SAFETY INSTRUCTIONS

• Check that the mains voltage corresponds to the rating of the appliance before operating.
• Use handles or knobs when moving. Place on a flat stable surface for use. Do not use outdoors.
• Do not use near or in the immediate vicinity of a bath or swimming pool or any source of liquid.
• Unplug from socket outlet when not in use.
• To protect against electric shock, do not immerse cord or plug in water or any other liquid.
• The use of accessory attachments not recommended by the appliance manufacturer, may cause injury.
• Do not locate this appliance immediately below a socket outlet.
• Do not allow cord to overhang the counter top where it can be easily pulled by children.
• Do not use this appliance for anything else other than its intended use.
• Do not overfill as this may cause a hazard. Ensure lid is closed when in operation
• To remove plug from outlet, do not pull on supply cord. Grasp plug firmly and pull to remove.
• No liability can be accepted for any damage caused by non compliance with these instructions or any other improper use or mishandling. This appliance is for household use only
• This appliance is not intended to be operated by means of an external timer or separate remote control system.
• This appliance is not intended to be immersed in water.
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
• Please according to local regulations regarding disposal of the appliance for its flammable blowing gas.
• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
• Fill with potable water only.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

This appliance contains the coolant isobutane (R600a),a natural gas which is environmentally friendly. Although it is flammable, it does not damage the ozone layer and does not increase the greenhouse effect. The use of this coolant has,however,led to a slight increase in the noise level of the appliance. In addition to the noise of the compressor,you might be able to hear the coolant flowing around the system. This is unavoidable,and does not have any adverse effect on the performance of the appliance. Care must be taken during the transportation and setting up of the appliance that no parts of the cooling system are damaged. Leaking coolant can damage the eyes.

WARNING
Danger from fire/flammable materials. Please observe the local regulations for the disposal of units with flammable refrigerants and gases.

• Keep ventilation openings in the unit housing free of obstacles.
• Do not damage the refrigerant circuit.
• Do not use any mechanical devices or other means to accelerate the defrosting process or the ice recovery process.
• Do not use other types of electrical appliances inside the ice cube machine.

Special Notes

• When positioning the unit, make sure that the power cord is not pinched or damaged.
• Make sure that there are no multiple sockets or power supplies on the back of the unit.

To avoid contamination of food, please follow the instructions below:

• Regularly clean surfaces that may come into contact with food. Clean the water drain regularly.
• If the appliance contains a water tank, clean it if it has not been used for 48 hours. Rinse the tank if no water has been removed for 5 days.

WARNING
When using, servicing and disposing of the unit, pay attention to the left symbol on the rear of the unit or on the compressor. This symbol warns of possible fires. There are flammable substances in the refrigerant lines and in the compressor. Keep the appliance away from sources of fire during use, maintenance and disposal.

PRODUCT OVERVIEW

1. Water drip tray
2. Water drip tray cover and support of the ice-cube container
3. Water drain plug
4. Hot Air outlet
5. Top window
6. Ice cube pushing spring
7. Control Panel
8. Evaporator
9. Side door
10. Water reservoir and the MAX level

A Display

1. TIMER setting delay time
2. Ice-cube size displaying: Small size.
3. Ice-cube size displaying: Large size.
4. Ice-cube obtaining symbol: with this symbol, the icecube will be pushed out.
5. Water dispensing symbol: with this symbol, water is flowing out now.
6. Error code.
7. Lack of water in reservoir symbol: With this symbol, the unit will stop running, need to pour water in.
8. Ice-full symbol: when it display, means the ice storage area is full of icecube.
9. ON/OFF symbol: if the unit has been turned off, this symbol will flash; And if the unit is turned on, this symbol will always display.

A   Display
B   Ice-cube obtaining button
C   Water dispenser button
D   ON/OFF Button: to turn on/off the unit
E SELECT Button: to select the size of the ice cube and the number code of all kinds of delay time
F   TIMER Button: to setting the timer-on or timer-off program

USE AND OPERATION

Before first Use

• Remove the exterior and interior packaging, Then check all the accessories are included. If any parts are missing, please contact our customer service.
• Remove all the tapes on the unit. Open the transparent window, take out the accessory parts inside.
• Clean the interior (such as water reservoir, Ice cube pushing spring etc.) with lukewarm water and a soft cloth.
• Locating your ice maker on a level counter table far from direct sunlight and other sources of heat (i.e.: stove, furnace, radiator). Maker sure that there is at least 15 centimeters between the back and sides of your ice maker with the wall.
• Allow one hour for the refrigerant fluid to settle down before plugging your ice maker in.
• The power plug must be accessible directly.

Note: fill with potable water only. Only use drinking water!

Operation

1. Open the left side door, pour potable water into reservoir. Keep water level below the “MAX” water level mark.

2. Plug your ice-maker into the main power outlet, then the symbol will flash in LCD display window.

3. Press “ON/OFF” button on the control panel to begin the ice making cycle. After this, the symbol will change to light on always in LCD display window, and   symbol will flash on in the mean time. The default size of ice-cube is Large. If you want to select the size of the ice cube, just press the “SELECT” button to select between Large size and Small size . If you still think the ice cube size is not fit for you, you can add the each ice-making cycle time by “SELECT” button. During the unit ice-making running, always press the “ON/OFF” button for more than 5 seconds, digit “0” will appear in the TIMER delay time displaying area of LCD window, which means the standard time of the once ice-making process, continue to press the “SELECT” button, the digit will change from 0 to 1, again 2, then return 0. After 5 seconds, the setting will complete and the digit will disappear and be remembered by the controller. With digit 1 setting, it will add 1 minute to standard duration time of each ice-making cycle, and the digit 2 setting, the added time will be longer more. And if the unit is plugged on again, it will recover to the digit 0 setting with standard time.
4. The ice making cycle lasts 6 to 12 minutes, depending on the size of the ice cube selection and the ambient temperature.
5. While the ice-maker is on, verify water level periodically. If water pump can’t pump out water, the ice maker will stop automatically, and the symbol will light on LCD displaying window and the arrow symbol will flash. Need to pour water into the water reservoir inside. We suggest you should press “ON/OFF” button to turn off the unit first, then fill water up to the MAX level mark, again press “ON/OFF” button to restart the unit. If you only fill the water in, but doesn’t press any button, you will need to wait some time to desire the ice-cube. Allow the refrigerant liquid inside the compressor at least 3 minutes to settle before restarting.

When Ice Full indicator is on

6. The ice maker automatically stops working when the ice-cube is full inside and the ice full” symbol on LCD displaying window will be indicated.

How to obtain the ice-cube

7. Put your ice-cube container on drip tray, press the “ICE” button one time on control panel (Button B in above illustration), the symbol will light on the LCD window, then the ice cube pushing spring start to rotate, the ice-cube will fall down into your ice-cube container from the ice-cube tap. And press the “ICE” button again, the symbol will disappear in the LCD window, the internal pushing spring will stop rotating and the ice-cube will not flow out again.

How to dispense the water

8. Default time of water flowing: 10 S. Put your water cup on drip tray, press the “WATER” button once on control panel (Button C in above illustration), the water will flow out from middle water tap, and the symbol will light on and the “10 S” will display in the TIMER delay time displaying area of LCD window, with the time pass, after 10 seconds, the symbol disappears and water dispensing will finish and water will not flow out again. If the water flowing time is too short or too long, you can set it again yourself. Always press the “WATER” button for more than 5 seconds, “10 ” will appear in the TIMER delay time displaying area of LCD window, continue to press the “SELECT” button to select the suitable time which range is from 7 seconds to 25 seconds. After 5 seconds, the setting will complete and the new digit will disappear and be remembered by the controller. Next time, if you want to dispense the water, it will work according to the new set time.

How to drain out the water inside the unit

9. When you clean the unit internal parts or change the drinkable water, need to drain out the left water in the water reservoir, just unplug the water drain cap which located at the bottom of the unit and near the water drip tray, the water will flow out from the unit completely. If the unit is supplied with the plastic soft tube, connect this soft tube with the water drain port, it can help you drain out the water easily.
10. Change water in the water reservoir every 24 hours to ensure a reasonable hygiene level. If the unit isn’t to be used, drain all water & dry the water reservoir.

Timer Setting

• Timer Delay Time Range: 0.5-19.5 hours. Default Delay Time: 1 hour.
• When the unit is running, you can set the unit with OFF-TIMER to let the unit stop running after your set delay time.
• And when the unit is on standby, you can set the unit with ON-TIMER to let the unit start to run automatically after your set delay time, then when you go back home or have a dinner, you can enjoy the happy life that this ice-maker give to you.

How to set the timer

Press the TIMER button first, the default delay time is 1.0 hour displayed delay time in LCD display window, then press the SELECT button to select your desired delay time. Each press SELECT button one time, the delay time will increase 0.5 hour, but if you always press the SELECT button, the delay time will change very quickly. During the process of delay time adjusting, the letter “H” will flash, then after 5 seconds flashing wit- hout pressing, the “H” letter will change from flashing to always displaying, means the timer program has been completed.

How to cancel the timer

When the unit has been set with the timer, press the TIMER button, then the delay time digit and “H” letter display will disappear, mean the timer set has been canceled.

1 = Timer delay time
2 = Means Hour, and timer setting duration

TROUBLESHOOTING

maker, fill water, and press “ON/ OFF” button again to restart the unit.
symbol is lightening and letter “F” flashes.| There is too much ice.| Suggest you to obtain the ice-cube.
No ice cube inside.| Remove the probable obstacle inside or clean the inside wall of the ice storage, if still can’t start to ice making process, press “SELECT” for more than 5 seconds to run the ice making for 10 cycles at most.
Errorcode | Ambient temperature sensor breakdown| The unit can still work, but suggest to call the manufacturer service man or electrical technician to change to a new sensor.
Errorcode | The ice-making box can not reset normally| Call the manufacturer service man or qualified technician to check the problem.
Ice cubes on the evaporator stick together.| The ice cycle is too long.| Stop the ice maker, and restart it after the ice blocks melt. Select the small size ice cube selection.
Water temperature in inner tank is too low.| Change the water in the inner Tank. Temperature of water is better set between 7-32 .
There are ice-cube inside the unit, but can’t dispense the ice-cube when you push the “ICE” button.| Moving shaft for the Icecube is blocked.| Release the button for ice-cube for 3 seconds, then again push the “ICE” button.
Ice making cycle is normal but no ice is made.| Ambient temperature or water temperature in inner tank is too high.| Please run the ice maker below 32 and pour colder water into tank.
Refrigerant liquid leakage.| Verify by a qualified technician.
Pipe in the cooling system is blocked.| Verify by a qualified technician.

CLEANING AND CARE

Before using your ice maker, it is strongly recommended to clean it thoroughly. Unplug the unit before cleaning or making any maintenance.

1. Take out the accessory parts under top window.
2. Clean the interior with diluted detergent, warm water and a soft cloth. First pour the warm water with diluted detergent into the internal water reservoir and the space below the transparent window, then use the soft cloth to wipe the surface.
3. Again use the water to rinse the inside parts, and drain out the water by unplugging the drain cap on the bottom.
4. The outside of the ice maker should be cleaned regularly with a mild detergent solution and warm water.
5. Dry the interior and exterior with a soft cloth.
6. When the machine is not in use for a long time, open water drain cap to drain out water completely from water reservoir.

HINTS ON DISPOSAL

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.

References

• Klarstein | Your home. Your kitchen. Your style.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>