KLARSTEIN 10034433 DryFy Connect Dehumidifier Instruction Manual

KLARSTEIN 10034433 DryFy Connect Dehumidifier

Dear Customer,
Congratulations on purchasing this equipment. Please read this manual carefully and take care of the following hints to avoid damages. Any failure caused by ignoring the items and cautions mentioned in the instruction manual is not covered by our warranty and any liability. Scan the QR code to get access to the latest user manual and other information about the product.

TECHNICAL DATA

Dehumidification

performance

| 30 L/Day| 40 L/Day| 50 L/Day
Tank capacity| 5 L| 7 L| 7 L
Air flow| 230 m²| 360 m²| 360 m²
Suitable room size| 25-30 m²| 35-45 m²| 45-55 m²
WiFi standard| 802.11 b/g/n
WiFi frequency| 2,4 GHz
WiFi radio-frequency power (max.)| 20 dBm

SAFETY INSTRUCTIONS

•  Place the unit on a level surface to reduce vibration and noise.
•  Do not place the unit in water or other liquids.
•  To prevent accidents, do not use the unit if cables or other connections are damaged.
•  This device may be used by children 8 years of age and older and by persons with limited physical, sensory or mental abilities and/or lack of experience and knowledge, provided they have been instructed in the device by a person responsible for them, can use the device safely and understand the risks associated with its use.
•  The device is not a toy. The cleaning and maintenance of the appliance may only be carried out by children aged 8 years and over under supervision.
•  Unplug the appliance from the wall outlet when you have stopped the appliance and wish to reset or clean it.
•  Only use the voltage indicated on the nameplate.
•  This device may only be used indoors.
•  Only use the unit for its intended purpose.
•  Do not place heavy objects on the device.
•  Empty the water tank after each use to avoid overflowing when restarting the unit.
•  Do not tilt the appliance to the side as this could allow the water in the water tank to enter the appliance and damage it.
•  Do not insert any foreign objects into the appliance as this may damage it.
•  If the power cord is damaged, it must be replaced by the manufacturer, customer service or a similarly qualified person to prevent damage.
•  Unplug the equipment from the wall outlet when it will not be used for a long period of time.
•  The power supply to the dehumidifier must comply with national safety regulations. Reliable grounding of the appliance must be ensured.
•  Do not place the unit near any heat sources (such as naked flames, heaters, etc.).
•  Do not switch the appliance on or off by plugging in or unplugging the mains plug.
•  Do not use sprays or other flammable substances near the product.
•  Do not scratch the surface of the product with sharp objects.
•  Do not allow water or oil to enter the interior of the unit.
•  Never clean the device with water. Rub it with a soft, slightly moistened cloth.
•  Do not rub the device with chemical solutions such as benzene, petrol, alcohol, etc. If the device is very dirty, rub it with a neutral cleaning agent.
•  Do not tilt the appliance by more than 45° and do not turn it upside down.

PRODUCT OVERVIEW AND KEY FUNCTIONS

1. Water tank
2.  Rear cover
3.  Water tank handle
4.  Grip
5.  Water tank cover
6. 10 Filter frame
7.  Wind leaf
8.  Drain plug
9. moisture indicator (only for article 10034433)
10.  Cable suspension
11. Control panel
12.  Wheel
13. Front cover

CONTROL PANEL

1. Timer
   24-hour timer setting. Press this button to set the time to turn the dehumidifier on/off. The setting range is 1 – 24 hours. If you want to cancel the timer setting, press the button twice after confirming the set time.

2. Dry key
   When you press this button, the inside of the dehumidifier is dried. This prevents the formation of mould. The entire drying process takes approximately one hour. Press this button again to cancel the drying function and return to the operating status.

3. Air velocity
   In the AUTO or CONTINUOUS settings, you can select between high (HIGH) and low (LOW) air speed.

4. LCD display
   In the AUTO, CONTINUOUS and DRYING modes, this display shows the ambient humidity. When humidity is set in Auto mode, this display shows the set humidity and shows the set time in Timer status. „%“ indicates the percentage of humidity.

5. Humidity Setting

   •  As soon as you press this button, the humidity in the range 30 % – 35 % – 40 % – 45 % – 50 % – 55 % – 60 % – 65 % – 70 % – 75 % – 80 % is displayed circulatingly. The humidity setting is for Auto mode only.
   •  Item 10034434 & 10034435: Press this button for about 3 seconds to turn the pump on/off.

6. Mode

   • During start-up or timer setting, press to select the mode.
   • The corresponding indicator light will light next to the selected mode.
   • Parental Lock: If you press and hold this button for more than 3 seconds, the parental lock is activated and the buttons cannot be operated. Press this button again for 3 seconds to deactivate the parental control.

7. Power On/Off
   Press the button to turn the unit on or off.

INSTALLATION

• When installing the unit, make sure that there is a minimum distance of 50 cm to the top and 20 cm to all sides of the unit (see figure below).
• If the unit is very noisy during operation, it is recommended to install rubber buffers or damping rubber mats underneath the dehumidifier to reduce vibration and noise. It also reduces the sinking of wooden and carpet floors.

Use without continuous water drainage
As soon as the water tank is full, the corresponding indicator light flashes (compressor, fan, etc. stop operation). The unit beeps 10 times to remind the user that the water needs to be drained.

Place both hands on each side of the rear cover. Carefully pull the water tank out of the unit and open the water tank cover on the right side of the water tank. Pour the water through the gap between the water tank and the water tank cover. Close the water tank cover and turn the water tank handle downwards. Replace the water tank in the appliance and restart the dehumidifier.Note: Empty the water tank when it is full. Before reinserting the water tank into the unit, make sure that the float is movable or not.

Setting up continuous water drainage (10034433)

Determine the position where the drain plug is located. Remove the drain plug.

Connect a drain pipe of appropriate length to the water outlet. Before use, make sure the drain line is properly connected, otherwise water leaks may occur. Note: The level of the connected drain hose must not be higher than the water outlet itself and the drain hose must be properly connected otherwise water leaks may occur because the water cannot drain properly.

Setting up continuous water drainage (10034434 & 10034435)
When the pump function is deactivated: Connect a drain line (outside diameter 13 mm) to the rear of the dehumidifier. Use a garden hose with a standard 26.98 mm outer diameter thread and 11.5 TPI inclination.
Note: With water-based plate cleaning function. Remove the appliance drain plug and clean the dehumidifier if you will not be using the appliance for an extended period of time. Hold a cup under the drain plug when removing it to prevent the floor from getting wet.

Determine the position of the drain plug and remove it. Connect a drain pipe with a diameter of 13 mm.Determine the position of the drain plug and remove it. Connect a garden hose.

Note: The drain line should not be too long (a length of less than 60 cm is recommended). The end of the drain line should be in a lower position than the water outlet (at least 10 cm lower), otherwise there is a risk of leakage.When the pump function is activated:Determine the position of the drain plug and remove it. Connect a drain pipe with a diameter of 5 mm.Note: Connect the drain line before activating the pump function to prevent the floor from getting wet.

Before the start

• Before switching on the appliance, remove the filter frame and insert the activated carbon filter (clean and dry the filter and filter frame regularly).
•  Do not turn on the unit until the filter frame and filter have been inserted correctly.

COMMISSIONING AND OPERATION

Timer (set time to automatically switch off)
When the dehumidifier is in operation, press the TIMER key to adjust the time from 1 h – 24 h. If you press the button once, the time is set to 1 hour. Pressing the button several times increases the time by one hour. If you press the button again after 24 hours, the time starts at 1 again. If the time you set has elapsed, the appliance switches off automatically. If no button is pressed within 5 seconds after the setting is completed, the set time to switch off is confirmed. When the auto power off time has been set, the timer indicator light will usually illuminate.

Timer (Setting the Time to Auto Power On)
When the unit is in standby mode, the auto power on time can be set in the same way as the auto power off time (see above). If no button is pressed within 5 seconds after the setting is completed, the set time to power on is confirmed. When the auto power on time has been set, the timer indicator light will usually light up.

AUTO Mode
If you select the automatic mode, the compressor and fan will run if the indoor humidity is higher than 5% higher than the set target humidity. If the indoor humidity is less than 5% higher or lower than the target humidity, the compressor and fan will continue to run at the set speed. If the indoor humidity is more than 5% lower than the target humidity, the compressor shuts down, but the fan continues to run at the set speed. The factory-set humidity value is 50%.

CONTINUOUS mode
If you select this mode, the compressor will start regardless of relative humidity. The factory setting is for the fan to run at maximum speed in this mode. The speed of the air circulation can be adjusted using the speed button.

Drying function in the air dehumidifier
Press the dry button (2) to activate the dry function of the dehumidifier. The entire process takes approximately one hour:

1.  The dehumidifier runs at high speed and releases air for more than 30 minutes.
2.  The dehumidifier changes to low speed and continues running for about 20 minutes.

Interrupt the drying function:

1.  If you press the dry button (2) again during the drying function, the drying function is aborted and the unit resumes its original operating status.
2.  Press the On/Off button (7) to cancel the drying function and place the appliance in standby mode.

Humidity Indicator
Press the humidity button (5) and mode button (6) simultaneously to turn the humidity indicator on/off. When the unit is in use, the color on the front of the unit changes depending on the humidity. If the humidity is greater than 60%, the unit will glow red. If the humidity is between 40% and 60%, the unit will glow green. If the humidity is less than 40%, the unit will glow blue. Pump Function (10034434 & 10034435)If you press and hold the humidity button (5) for more than 3 seconds, the pumping function is activated/deactivated. (Connect a drain hose before activating the pumping function.)Air swing function (10034434 & 10034435) If you start the timer button (1) and the dry button (2) at the same time, the air swing function is started or stopped.

DEVICE CONTROL BY SMARTPHONE

If you integrate the device into your home WiFi, you can conveniently operate it via the associated Klarstein app. The app not only allows you to remotely control the device via your smartphone but also gives you access to recipes and additional information. Follow these steps to connect your smartphone to your Klarstein device:

1.  Download the Klarstein app first by scanning the QR code with your smartphone (see below), or download it directly from App Store or Google Play.
2.  Make sure your smartphone is connected to the same WiFi network that your Klarstein device is to be connected to.
3.  Open the Klarstein app.
4. Sign in to your account. If you do not have an account, sign up in the Klarstein app. 5 Follow the instructions from the app.

App Download

Use the scan function of your smartphone to scan the QR code and save the app on your smartphone.Note: The app provides further information on how to use the app and help on how to connect to your device as soon as you open it for the first time.

Troubleshooting connection problems

If your Klarstein device cannot be found in the WLAN, check the following:

•  Is the device plugged in?
•  Is the WiFi feature of my phone enabled?
•  Is the WiFi function of the Klarstein device activated? (Follow the instructions in the app)
•  Has the WLAN password been entered correctly?
•  Are the router, Klarstein device and smartphone in the immediate vicinity during the connection attempt? (Ideally no more than 5 m apart)
•  If you have deactivated the 2.4 GHz band in the settings of your wireless router, activate it in your router settings.

Note: For further help, follow the instructions in the app when setting up the connection.

CLEANING AND CARE

Precautions

•  To avoid electric shock, unplug the appliance from the wall outlet before cleaning or servicing.
•  Unplug the appliance from the wall outlet when not in use for an extended period of time.
•  Do not clean the body of the appliance with chemical solutions such as alcohol, petrol, benzene, etc..

Cleaning the individual parts

Clean the water tank and the water tank cover regularly with a slightly moistened cloth so that no mould can form inside. Rub the surface of the appliance with a slightly moistened cloth. Do
not use detergents or abrasive sponges to avoid damaging the plastic surface. Clean the washable PP grid with warm or cold water at least once every two weeks. Do not use chemical solutions or hot water.

TROUBLESHOOTING

plugged into the socket.

| Insert the mains plug into the socket.
The water tank may be full

or incorrectly inserted.

| Drain the water from the water tank or insert it properly.
Room temperature is lower than 5°C or higher than 32°C.| This is normal at these temperatures and not a fault condition.
Dehumidifying the room air is not effective.| The room temperature or

humidity is too low.

| In the dry season, the dehumidifiability is reduced.
The air inlet or outlet is

blocked.

| Clean the air inlets and outlets.
No air is blown out.| The ventilation grille is

blocked.

| Clean the ventilation grille.
Unusual noise during

operation.

| The dehumidifier is standing on an uneven surface.| Place the dehumidifier on a flat surface.
The ventilation grille is

blocked.

| Clean the ventilation grille.
A splashing noise can be heard.| This is normal. It is a

circulating coolant.

Water escapes.| The connection between water outlet and drain pipe is loose.| Tighten the connection.
The drain system is

blocked.

| Remove obstructions and straighten the drain line.
Frost occurs.| The ambient temperature

is low.

| This is a normal phenomenon. The dehumidifier has an automatic defrost function.

Frequently Asked Questions

temperatures are lower and the air is drier. The dehumidifying capacity therefore decreases compared to summer. This is not a fault of the unit.
Why does the unit not run or stops

abruptly?

| The dehumidifier’s water tank may be full or incorrectly installed. Drain the water or insert the water tank correctly into the appliance.
The ambient temperature may be too high or too low. The dehumidifier will only operate at temperatures between 5 and 32°c and relative humidity between 30% and 80%. The optimal operating

temperature is 16 – 32 °c.

Why does hot air come from the air

outlet?

| This dehumidifier draws in the room

air and cools it down to a temperature below the condensation point so that the air condenses into drops of water that fall into the water tank. The dehumidified air is then reheated and exits the air outlet. This reduces energy consumption and accelerates dehumidification. The outlet of hot air is not a fault.

Error codes (only for 10034434 & 10034435)

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service. This product contains batteries. If there is a legal regulation for the disposal of batteries in your country, the batteries must not be disposed of with household waste. Find out about local regulations for disposing of batteries. By disposing of them in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences.

DECLARATION OF CONFORMITY

• Manufacturer: Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.
• Importer for Great Britain: Chal-Tec UK limited
• Unit 6 Riverside Business Centre
• Brighton Road
• Shoreham-by-Sea
• BN43 6RE
• United Kingdom
• The complete declaration of conformity of the manufacturer can be found at the following link: use.berlin/10034435

References

• Klarstein | Your home. Your kitchen. Your style.
• Take-e-way GmbH | take-e-back | Elektroschrott Rücknahmesystem Onlinehandel

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>