KLARSTEIN 10035202 Bern Smart Fireplace Heater Instruction Manual

June 5, 2024
Klarstein

10035202 Bern Smart Fireplace Heater
Instruction Manual

Dear Customer,
Congratulations on purchasing this device. Please read the following instructions carefully and follow them to prevent possible damages. We assume no liability for damage  caused by disregard of the instructions and improper use. Scan the QR code to get access to the latest user manual and more product information.

KLARSTEIN 10035086 Bormio Smart Fireplace Heater - BR
codehttps://use.berlin/10035086

TECHNICAL DATA

Item number 10035202, 10035203, 10035204
Power supply 220-240 V ~ 50/60 Hz
Power consumption 2000 W
WiFi standard 802.11 b/g/n
WiFi frequency 2,4 GHz
WiFi radio-frequency power (max.) 20 dBm

SAFETY INSTRUCTIONS

  • Check that the voltage indicates on the data plate corresponds with that of the local network before connecting the appliance to the mains power supply.

  • If the supply cord is damaged, it must be replaced by a qualifi ed engineer in order to avoid a hazard.

  • The fi replace heater must not be positioned directly under the power socket.

  • Keep furniture, curtains and other fl ammable material at least 1 meter away from the appliance.

  • Keep out of reach of children and do not allow them to operate this appliance.

  • This appliance is intended for household use only and should not be used for industrial purposes.

  • Do not operate this appliance after a malfunction or after being damaged in any way.

  • Repairs to electrical appliances should only be performed by a qualifi ed electrician.

  • Improper repairs may place user at serious risk.

  • Do not run the mains cable under carpets, rugs, etc.

  • Do not allow the mains cable to hang over sharp edges or come in contact with hot surfaces.

  • In order to avoid overheating, do not cover the heater.

  • Do not use this heater with a programmer, timer, separate remote control system or any other device that switches the heater on automatically, since a fi re risk exists if the  heater is covered or positioned incorrectly.

  • Never immerse the product in water or any other liquid for any reasons.

  • Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.

  • Do not use the appliance outdoors.

  • Do not use if you have wet hands.

  • Never use the appliance on or near hot surfaces.

  • Do not operate with a damaged cord.

  • Before cleaning the appliance, make sure it is unplugged from the power and that it is completely cooled.

  • Do not clean the appliance with abrasive chemicals.

  • Never use accessories that are not recommended or supplied by the manufacturer.
    It could cause danger to the user or damage to the appliance.

  • This device may be only used by children 8 years old or older and persons with
    limited physical, sensory and mental capabilities and / or lack of experience and knowledge, provided that they have been instructed in use of the device by a responsible person  who understands the associated risks.

  • Children should be supervised to ensure that they do not play with the appliance.

CAUTION
Risk of burns! Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

DEVICE OVERVIEW AND BUTTONS

KLARSTEIN 10035202 Bern Smart Fireplace Heater - DEVICE OVERVIEW AND
BUTTONS

ASSEMBLY 10035204

KLARSTEIN 10035202 Bern Smart Fireplace Heater -
ASSEMBLY

WALL MOUNTING

The fireplace can be mounted on the wall. Before fixing the fireplace, make sure that the fireplace is on a level surface.

  1. Use a pen to mark the position of the holes for the supplied bracket.
  2. Drill holes in the back of the fireplace with a thin drill bit (2 mm).
  3. Fasten the brackets to the fireplace with the 4 white screws.
  4. Place the heater on the wall and mark the position of the bracket holes on the wall with a pen. Then remove the heater from the wall.
  5. Drill holes in the wall with a drill bit (6 mm) and insert the two plugs supplied.
  6. Place the heater back on the wall and fasten it with the two long screws.

KLARSTEIN 10035202 Bern Smart Fireplace Heater - WALL
MOUNTING

CONTRIL PANEL

REMOTE CONTROL

| Power button| • Press this button to switch the unit on/off
---|---|---
| Flame button| • To adjust the flame brightness: Press this button once and then adjust  the flame brightness using the arrow buttons.
• To adjust the flame color: Press the Flame button twice, then use the  Arrow buttons to switch between flame colors (C1 – C7).
| Arrow keys| • Press these buttons to select between the different heating levels. The  level you select is shown on the heat indicator. When the small bar lights up, a low heating level is set. When both bars are lit, a high
heating level is set.
| Temperature button| • Press this button once and use the arrow buttons to select the desired  temperature (18 – 35 °C).
| Timer button| • While the unit is on, press this button to set the time until it switches off  automatically. You can set 0 – 9 hours in 1-hour increments. As soon as the time you
set has elapsed, the fire will automatically go out.
• To adjust the colour of the backlight, keep this key pressed until you hear a beep and  „F1“ is displayed on the screen. Then press the timer button repeatedly to select one of  the colours. Once you reach „F9“, the setting mode is exited and the colour  selection starts again.

DISPLAY SCREENS

KLARSTEIN 10035202 Bern Smart Fireplace Heater - DISPLAY
SCREENS

COMMISSIONING AND OPERATION

On/Off

  • Press the Power button to switch the unit on/off.
  • In standby mode, press and hold the Power button for 3 seconds to reset the wireless network.
  • Press and hold the Power button for 5 seconds in standby mode to toggle between Celsius and Fahrenheit.

Flame Controller

  • Press the Flame button repeatedly to adjust the flame brightness. There are 5 levels.
    5 is the highest level and 1 is the lowest level.

  • Press and hold the Flame button for 5 seconds to enter the Flame color setting.
    Afterwards you can choose between the colours C1

  • C7 by pressing several times.

C1 Warm White + Red + Blue

C2 Warm white + red
C3 Red + Blue
C4 Warm white + blue
C5 Blue
C6 Red
C7 Warm white

Heat controller

  • Press the Heat button repeatedly to select between the different heat levels. The level you select is indicated on the screen by a bar. When the small bar lights up, a low heat  level is set. When both bars are lit, a high heat level is set.
  • Press and hold the Heat button for 5 seconds to set the desired heating temperature.
    You can set a temperature between 18 and 35 °C.

Timer

  • Press the Timer button several times in standby mode to set a power-on timer. A timer between 0 and 9 hours can be set. Each time the Timer button is pressed, the time is  adjusted at 1-hour intervals.
  • To adjust the LED backlight, press the Timer button until you hear a beeping sound.
    F1“ is then displayed on the glass window. A total of 8 background colours can be selected. Press the Timer button briefly to change the colour. As soon as „F9“ is reached,  the menu is exited and the colours start again when pressed again.

Open window detection
If the room temperature falls below 5 °C within 3 minutes while the unit is operating and does not rise within 7 minutes, the unit automatically assumes that a window is open.  To save energy, the heating function is switched off and a warning signal sounds. Alarm „E4“ is displayed on the screen.

CLEANING AND CARE

Note: Turn off the unit and unplug it from the power outlet. Wait until the unit has completely cooled down before cleaning it.

  • Use a vacuum cleaner to clean the ventilation slots and grilles.
  • Remove dust on the outside surfaces with a damp (not wet) cloth.
  • Do not use strong cleaning agents or abrasives.
  • Do not spray the device with liquids or immerse it in water or other liquids.
  • Never open the heater housing.

Storage
Keep the unit in a dust-free place during the low season. Pack it in the original carton.
Wind the heater cable cleanly to avoid damaging the cable.

DEVICE CONTROL BY SMARTPHONE

If you integrate the device into your home WiFi, you can conveniently operate it via the associated Klarstein app. The app not only allows you to remotely control the device via
your smartphone, but also gives you access to recipes and additional information.

Follow these steps to connect your smartphone to your Klarstein device:

  1. Download the Klarstein app first by scanning the QR code with your smartphone (see below), or download it directly from App Store or Google Play.
  2. Make sure your smartphone is connected to the same WiFi network that your Klarstein device is to be connected to.
  3. Open the Klarstein app.
  4. Sign in to your account. If you do not have an account, sign up in the Klarstein app.
  5. Follow the instructions from the app.

App Download
Use the scan function of your smartphone to scan the QR code and save the app on your smartphone.

Note: The app provides further information on how to use the app and help on how to connect to your device as soon as you open it for the first time.

KLARSTEIN 10035086 Bormio Smart Fireplace Heater - App
Downloadhttps://apps.apple.com/app/id1479571307#?platform=iphone
https://play.google.com/store/apps/details?id=com.chaltec.klarsteinrn&hl=en

Troubleshooting connection problems
If your Klarstein device cannot be found in the WLAN, check the following:

  • Is the device plugged in?
  • Is the WiFi feature of my phone enabled?
  • Is the WiFi function of the Klarstein device activated? (Follow the instructions in the app)
  • Has the WLAN password been entered correctly?
  • Are the router, Klarstein device and smartphone in the immediate vicinity during the connection attempt? (Ideally no more than 5 m apart)
  • If you have deactivated the 2.4 GHz band in the settings of your wireless router, activate it in your router settings.

Note: For further help, follow the instructions in the app when setting up the connection.

PRODUCT DATA SHEET

Model identifier(s): 10035202, 10035203, 10035204
Item Symbol
Heat output

heaters only
Nominal heat output| Pnom| 2.0| kW| | manual heat charge control, with integrated thermostat| N/A
Minimum heat output (indicative)| Pmin| 1.0| kW| | manual heat charge control with room and/or outdoor temperature feedback| N/A
Maximum continuous heal output| Pmax,c| 2.0| kW| | electronic heat charge control with room and/or outdoor temperature feedback| N/A
Auxiliary electricity consumption| | fan assisted heat output| N/A
At nominal heat output| elmax| N/A| kW| |
Type of heat output/room temperature control
At minimum heat output| elmin.| N/A| kW| | single stage heat output and no room temperature control| no
In standby mode| elSB| 0.0| W| | Two or more manual stages, no room temperature control| no
| | with mechanic thermostat room temperature control| no
| with electronic room temperature control| no
| electronic room temperature control plus doy ti mer| no
| electronic room temperature control plus week ti mer| yes
|
Other control options (multiple selections possible)**
| room temperature control, with presence detection| no
| room temperature control, with open window detection| yes
| with distance control option| no
| with adoptive start control| no
| with working time limitation| no
| with black bulb sensor| no
Contact details| Chal-Tec GmbH, WallstroBe 16, 10 79, Berlin, Germany

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must
not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance  with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of  this product, please contact your local authority or your household waste disposal service.

This product contains batteries. If there is a legal regulation for the disposal of batteries in your country, the batteries must not be disposed of with household waste. Find out  about local regulations for disposing of batteries. By disposing of them in accordance with the rules, you are protecting the environment and the health of your fellow human  beings from negative consequences.

DECLARATION OF CONFORMITY

Manufacturer:
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.
Importer for Great Britain:
Chal-Tec UK limited
Unit 6 Riverside Business Centre
Brighton Road
Shoreham-by-Sea
BN43 6RE
United Kingdom

The complete declaration of conformity of the manufacturer can be found at the following link: use.berlin/10035202

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals