KLARSTEIN 10035064 Hot Spot Crystal Spotless Smart Infrared Heater Instruction Manual

10035064 Hot Spot Crystal Spotless Smart Infrared Heater
Instruction Manual
www.klarstein.com

Note: This product is only suitable for well insulated spaces or occasional use.

Dear Customer,
Congratulations on purchasing this device. Please read the following instructions carefully and follow them to prevent possible damages. We assume no liability for damage  caused by disregard of the instructions and improper use. Scan the QR code to get access to the latest user manual and more product information.

https://use.berlin/10035064

TECHNICAL DATA

SAFETY INSTRUCTIONS

• Do not use the appliance until it is securely fi xed as described in this manual.

• Check that the voltage indicates on the data plate corresponds with that of the local network before connecting the appliance to the mains power supply.

• If the supply cord is damaged, it must be replaced by a qualifi ed engineer in order to avoid a hazard.

• The fi replace heater must not be positioned directly under the power socket.

• Keep furniture, curtains and other fl ammable material at least 1 meter away from the appliance.

• Do not leave the appliance unattended during use.

• Do not leave the appliance unattended whilst connected to the mains supply.

• Keep out of reach of children and do not allow them to operate this appliance.

• This appliance is intended for household use only and should not be used for industrial purposes.

• Do not operate this appliance after a malfunction or after being damaged in any way.

• Repairs to electrical appliances should only be performed by a qualifi ed electrician.

• Improper repairs may place user at serious risk.

• Do not run the mains cable under carpets, rugs, etc.

• Do not allow the mains cable to hang over sharp edges or come in contact with hot surfaces.

• In order to avoid overheating, do not cover the heater.

• Do not use this heater with a programmer, timer, separate remote control system or any other device that switches the heater on automatically, since a fi re risk exists if the  heater is covered or positioned incorrectly.

• Never immerse the product in water or any other liquid for any reasons.

• Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.

• Do not use the appliance outdoors.

• Do not use if you have wet hands.

• Never use the appliance on or near hot surfaces.

• Do not operate with a damaged cord.

• Before cleaning the appliance, make sure it is unplugged from the power and that it is completely cooled.

• Do not clean the appliance with abrasive chemicals.

• Never use accessories that are not recommended or supplied by the manufacturer.
  It could cause danger to the user or damage to the appliance.

• This appliance is not intended for use by persons (including children) with reduced Physical, sensory or mental capabilities, or lack of experience and knowledge
  unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

CAUTION
Risk of burns! Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.

PRODUCT DATA SHEET

INSTALLATION

Installation instructions
If you have a tool, you can install the device according to the procedure described in the operating instructions. It is also possible to ask the seller, his service department or a similarly qualified electrical installation company to install the equipment.

Step 1
Before installing the unit as shown in the figure below, use the installation positioning cardboard box A1 with holes to mark the installation position on the wall (the wall must be able to support the weight of the unit). When applying the mark, the horizontal side of the cardboard must be parallel to the floor. In the position with the mark, drill four holes with a 10 mm hole and a depth of no less than 70 mm. Make sure that the hole is perpendicular to the wall. Make sure that the lateral distance and the vertical distance between two holes are as shown in the figure below:

The distance between the holes should be as shown below:

WARNING
Danger of injury! To avoid danger for small children, this unit should be installed so that the lowest heated rail is 550 mm above the fl oor.

Fix the 4 brackets to the wall with the expansion screw. The fixed brackets can be moved to adjust the position to fix the glass panel.

Step 2
First remove the protective film on the back of the glass. Then fix the glass panel to the already attached wall bracket.
Note that the attached wall bracket can be moved for the  installation of the glass panel. Then tighten the screws on the side of each bracket cover (4 in total).

DISPLAYS AND FUNCTION KEYS

Control panel

Remote control

COMMISSIONING AND OPERATION

Before using the device, make sure that the device and its accessories are in good condition.
Since some of the elements are disassembled for packing when shipped from the factory, these special elements are removed separately when you take them out of the packing  box. Since the unit is mainly made of glass, carefully check that it is in good condition when removing it from the packaging. If you discover that it has been damaged during  transport, immediately inform the manufacturer or customer service.

Operation

• Place the device on a stable surface.
• Insert the power plug of the unit into a 220-240 V ~ 50 Hz power outlet and set the power switch located on the side of the unit to the „I“ position. A beep will then be heard.
• Switch the unit on by pressing the button . The LE screen displays the room temperature. You can set the power, temperature and time by touching the control panel or remote control.
• Turn the unit off and unplug the power cord from the wall outlet when it is not used for a long period of time.
• Do not cover the unit under any circumstances. Do not place the unit in showers or swimming pools.

Switch on
First, set the power switch of the device, which is located on the side of the device, to the „I“ position. Press the button to set the function. The upper part of the control panel
displays the room temperature. The unit will now run at a low power level.

Mode
Press the Mode button to adjust the power.

Temperature adjustment
Press the temperature button to set the desired temperature in the range 5 °C – 40 °C.
Each time the appliance is started, the indoor temperature is displayed. When the indoor temperature reaches the temperature you set, the unit will switch from high to low  power.
If the room temperature is at least 2 °C higher than the set temperature, the unit stops operating. As soon as the temperature drops by 2 °C again, the unit resumes operation, depending on the set target temperature.

Timer
The timer can be set to automatically switch the unit on or off at a desired time. A time interval between 1 and 24 hours can be set.
Parental lock
If you press and hold the parental control button on the remote control for 3 seconds, all buttons are disabled. You can deactivate the parental control in the same way. If you do not have the remote control at hand, you can press and hold the heat button on the control panel for 5 seconds to lock/unlock the screen.

DEVICE CONTROL BY SMARTPHONE

If you integrate the device into your home WiFi, you can conveniently operate it via the associated Klarstein app. The app not only allows you to remotely control the device via your smartphone, but also gives you access to recipes and additional information.
Follow these steps to connect your smartphone to your Klarstein device:

1. Download the Klarstein app first by scanning the QR code with your smartphone (see below), or download it directly from App Store or Google Play.
2. Make sure your smartphone is connected to the same WiFi network that your Klarstein device is to be connected to.
3. Open the Klarstein app.
4. Sign in to your account. If you do not have an account, sign up in the Klarstein app.
5. Follow the instructions from the app.

App Download
Use the scan function of your smartphone to scan the QR code and save the app on your smartphone.
Note: The app provides further information on how to use the app and help on how to connect to your device as soon as you open it for the first time.

https://apps.apple.com/app/id1479571307#?platform=iphone
https://play.google.com/store/apps/details?id=com.chaltec.klarsteinrn&hl=en

Troubleshooting connection problems
If your Klarstein device cannot be found in the WLAN, check the following:

• Is the device plugged in?
• Is the WiFi feature of my phone enabled?
• Is the WiFi function of the Klarstein device activated? (Follow the instructions in the app)
• Has the WLAN password been entered correctly?
• Are the router, Klarstein device and smartphone in the immediate vicinity during the connection attempt? (Ideally no more than 5 m apart)
• If you have deactivated the 2.4 GHz band in the settings of your wireless router, activate it in your router settings.

Note: For further help, follow the instructions in the app when setting up the connection.

CLEANING AND CARE

• Always unplug the appliance from the power outlet and allow it to cool down completely before cleaning and servicing the appliance.
• Clean the air vents regularly.
• Never use aggressive or abrasive cleaning agents for cleaning.
• Clean the outer cover with a soft, damp cloth. Do not allow any liquid to penetrate the heater!
• Never use alcohol, petrol, abrasive cleaners, furniture polish or coarse brushes to clean the heater. This may cause damage or wear to the surface of the heater.
• If you do not use the heater for a long time, remove the batteries from the remote control (to prevent corrosion) and store the remote control in a safe place.

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical nd electronic devices in your country, this symbol on the product or on the packaging indicates that this product  must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and lectronic equipment. By disposing of it in  accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.

DECLARATION OF CONFORMITY

Manufacturer :
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.
Importer for Great Britain:
Chal-Tec UK limited
Unit 6 Riverside Business Centre
Brighton Road
Shoreham-by-Sea
BN43 6RE
United Kingdom
The complete declaration of conformity of the manufacturer can be found at the following link: use.berlin/10035064

References

• Klarstein | Your home. Your kitchen. Your style.
• Take-e-way GmbH | take-e-back | Elektroschrott Rücknahmesystem Onlinehandel

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>