KLARSTEIN 10034664 Kraftwerk Smart Air Conditioner Instruction Manual

KRAFTWERK SMART
Air Conditioner

10034664 10034665 10034666 10034667 10035737 10035738 10035739 10035740

www.klarstein.com

Dear Customer,
Congratulations on purchasing this device. Please read the following instructions carefully and follow them to prevent possible damages. We assume no liability for damage caused by disregard of the instructions and improper use. Scan the QR code to get access to the latest user manual and more product information.

https://use.berlin/10034664

SAFETY INSTRUCTIONS

General Safety Instructions

• The air conditioning is only suitable for indoor use and is not suitable for other applications.
• Follow local grid interconnection rules while installing the air conditioning and ensure that it is properly grounded. If you have any question on electrical installation, follow the instructions of the manufacturer, and if necessary, ask a professional electrician to install it.
• After the air conditioning is installed, ensure that the power plug is intact and firmly plugged into the power outlet, and place the power cord orderly to prevent someone from being tripped or pulling out the plug.
• Do not put any object into the air inlet and outlet of the air conditioning. Keep the air inlet and outlet free from obstructions.
• When drainage pipes are installed, ensure that the drainage pipes are properly connected, and are not distorted or bended.
• While adjusting the upper and lower wind-guide strips of the air outlet, pluck it with hands gently to avoid damaging wind-guide strips.
• Do not disassemble, overhaul and modify the machine arbitrarily, otherwise, it will cause a machine malfunction or even bring harm to persons and properties. To avoid danger, if a machine failure occurs, ask the manufacturer or professionals to repair it.
• Do not install and use the air conditioning in the bathroom or other humid environments.
• Do not pull the plug to turn off the machine.
• Do not place cups or other objects on the body to prevent water or other liquids from spilling into the air conditioning.
• Do not use insecticide sprays or other flammable substances near the air conditioning.
• Do not wipe or wash the air conditioning with chemical solvents such as gasoline and alcohol. When you need to clean the air conditioning, you must disconnect the power supply, and clean it with a half-wet soft cloth. If the machine is really dirty, scrub with a mild detergent.
• The appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and maintenance shall not be made by children without supervision.

Instructions for placement

• Place the machine in a flat and dry place and keep a distance of above 50 cm between the machine and the surrounding objects or walls.
• When moving the machine, make sure that it is in an upright position.
• The machine should stay away from gasoline, flammable gas, stoves and other heat sources.
• The room must not be smaller than 4 m² (10034666, 10034667, 10035737, 10035738) or 10 m² (10034664, 10034665, 10035739, 10035740).

DEVICE DESCRIPTION

1. Control panel
2. Remote control
3. Air outlet
4. Air inlet
5. Exhaust air outlet| 6. Air inlet
7. Water stopper/drainage point
8. Air inlet
9. Cord storage
10. Air inlet
---|---

Accessories

11 Exhaust hose
12 Adaptor – for insertion over hose and into window spacer (or into hole in the wall/window).
13 Connector for exhaust pipe| 14 Drain tube for continuous drainage
15 Active carbon fi lter
16 Remote control
---|---

INSTALLATION

Using the connector

Have a 160 mm diameter hole in the wall or window.
Feed exhaust hose through the window or wall and attach the threaded adaptor from the outside as shown.

Mounting of the exhaust pipe
Use only the hose provided and clip exhaust hose to the back of the air conditioner Avoid kinks and bends in the exhaust hose as this will cause expelled moist air to build up causing the unit to overheat and shut down. Figure 7 & 8 show correct position The hose may be extended from 300 mm to 1500 mm but for maximum efficiency use the shortest length possible.

ATTENTION: The length of the exhaust pipe is specially designed according to the specification of this product. Do not replace or prolong it with your own private hose as this could cause the unit to malfunction!

INSTALLATION OF THE CARBON FILTER

1. Remove the plastic filter from the unit.

2. Remove the active carbon filter from its plastic bag.

3. Place the active carbon filter onto the unit.

4. Replace the plastic filter on to the unit.

OPERATION

Control panel

1 ON/OFF (power) soft-touch button
2 Speed (ventilation) soft-touch button
3 “Timer” indicator
4 “Timer” soft touch button
5 “Sleeping” model soft touch button
6 “Sleeping” model indicator
7 Mode (function) option soft touch button
8 ‘Temperature up’ soft touch button
9 ‘Temperature down‘ soft touch button
10 Indicators for compressor operation
11 “Full Water” indicator| 12 Low ventilation indicator
13 Middle ventilation indicator
14 High ventilation indicator
15 Receiver for remote control
16 Display window
17 Automatic mode indicator
18 DEHUMIDIFY(DRY) mode indicator
19 Cooling mode indicator
20 Fan mode indicator
21 WiFi mode indicator
22 WIFI mode button
---|---

All the above functions can also be performed with the supplied remote control.
This remote control requires battery CR2032 x 1pc to operate

Turning ON/OFF

1. Press ON/OFF soft touch button, the unit will start automatically. If the ambient temperature is higher or equal to 24 °C, the unit will work in cooling mode. If it is below 24 °C, the unit will work in ventilation mode (low fan).
2. Indicators of the functions in progress come on at the same time. The display window shows the ambient room temperature from 0 °C to 50 °C.
3. To turn the unit off, press ON/OFF button again.

Setting mode/function
Press MODE button to select required working mode: automatic, cooling, fan or dehumidify (dry). The indicator of your selected mode lights on.

Setting temperature

1. Press ‘Temperature up’ or ‘Temperature down’ button to regulate the temperature you desired.
2. The display window will show the temperature you set as you press ‘Temperature up’ or ‘Temperature down’ button. Otherwise, it will always show the ambient temperature.
3. The pre-setting temperature of this machine is: 24 °C for cooling.

Setting ventilation speed

1. Press SPEED button to choose the ventilation speed you need, high, medium or low. The indicator of high, medium or low ventilation will light on at the same time.
2. If the unit is in AUTO mode, it will choose the ventilation speed automatically according to the ambient temperature (the related indicators will light on), at this time, the SPEED and TEMPERATURE UP & DOWN buttons are invalid.

Setting timer

1. Press TIMER button to set the operating hours you desired (1 to 24 hours, the timer indicator will light on). When the set time has been reached, the machine will turn off automatically. The display window will show the hour(s) you set as you press TIMER button. If the timer button is not pressed, the unit will work continuously.
2. By pressing the timer but without turning on the other functions, you can PRE-SET the time for the machine to work. For example, if you press the timer to ‘2’, the unit will work automatically after 2 hours.

Sleep function

1. In cooling mode, by pressing the SLEEP button, the set temperature will increase 1 °C at the 1st hour, another 1 °C at the second hour, then keeps at that temperature.
2. In sleep mode, the ventilation will keep at low speed. Re-press the SLEEP button, the setting temperature and ventilation speed will return to the pre-selected one.
3. The unit will shut down automatically after the SLEEP function running for 12 hours.
4. Please note, the sleep function is not available while the machine is working in AUTO, FAN (ventilation) or DEHUMIDIFICATION mode.
5. When the machine is in Sleep function, the Fan Speed would turn to be LOW speed.

Dehumidify (DRY) mode
In dehumidify (DRY) mode, the temperature cannot be adjusted, the ventilation will fix at low speed. When the unit is operating in Dehumidify ( DRY) mode, humidity extracted from the air is collected in an internal tank. If the tank reaches full, the compressor and motor cut out automatically. At the same time, the “Water Full” indicator comes on. An alarm will also sound. When the tank is full, drain the water as shown in the page concerning “DRAINAGE”. You may also use the unit without having to empty the tank so often by using “continuous drainage”, please also refer to the page about “DRAINAGE”.

Self-diagnosis
This machine is equipped with self-diagnosis function. If something is wrong in the machine, the display window will show the sign: E1, E2, E3 or E5 , which reflects different condition. At this time, please call your service centre.

Notes

• To prolong the compressor’s life, after switch-off of the unit, please wait for 3 minutes (at least) before re-switch.
• The cooling system will switch off if the ambient temperature is lower than the set one. The ventilation, however, keeps working on the set level. If the ambient temperature rises above the selected level, the cooling will return to work.

DRAINAGE

During the process of cooling, some water will be extracted from the air into the unit.
If the reservoir is full, both of the compressor and motor will stop and the units would buzz (you can press any button to stop the buzz). The W.F. indicator will flash to show you.
To make the cooling work again, please empty the water by one of the following ways:

1. Turn off the air conditioner and avoid moving it when full.
2. Position a container (a water tray for example) underneath the drain hole.
3. Remove the drain knob & rubber plug from the drain hole and allow the water to drain out.
4. When the container is almost full, replace the rubber plug in the drain hole and empty the water tray.
5. Repeat until the unit is emptied.
6. Replace the rubber plug and tighten the drain knob firmly.
7. Switch on the unit – the full water or compressor operating indicator should not be flashing.

If you wish to operate the unit without the need to empty the water tank, please:

• Remove the drain knob and rubber plug and retain for future use.
• Connect the drain tube supplied to the water outlet as shown and locate the other end into a drain.

The drain tube may be extended by adding an extension tube and using a suitable connector.

Please note :

1. The drain must be at or below the outlet level.
2. Flashing ‘full water’ indicator will not function in this mode of drainage.
3. If you want to extend the water tube, you can connect it with another tube (OD: 18 mm).

HOW TO INSTALL THE WINDOW SEAL

Installing the window sealing is easy. You can attach it to a tilted window or to a laterally opened window. Our demonstration is performed on a laterally opened window. It is especially suitable for low positions of the exhaust pipe.
The velcro tape must be attached on three sides. Leave out the side with the window being connected to the frame. Clean the frame and dry it first, so that the tape sticks.

Attach the velcro tape on the left, on the top and on the bottom of the window frame.
We recommend that you cut the tape into strips for each window side first.| Now attach the velcro tape to the inner window sides.| Stick the window sealing to the velcro strips on
the window frame first (starting with the top), then on the velcro strips on the window.
Push the exhaust air tube of the air conditioner
through the hole, which can be adjusted in height
and size.

CLEANING AND CARE

Always unplug the air conditioner from the mains before cleaning.
To maximize the efficiency of the air conditioner, clean regularly.

Cleaning the housing
Use a soft, damp cloth to wipe the body clean.
Never use aggressive chemicals, gasoline, detergents, chemically treated cloths, or other cleansing solutions. These all could possibly hurt the cabinet.

Cleaning the filter
Use a vacuum cleaner or tap the filter lightly to remove loose dust and dirt from the filters and then rinse thoroughly under running water (no hotter than 40 °C). Dry thoroughly before replacing.
Notice! Never operate the unit without the filters.

End of season storage

• Drain any water in the unit before completely operating the unit on ventilation only mode for a few hours, to thoroughly dry the inside.
• Clean or change the filter.
• Unplug and store the power cord.
• Replace in the original carton or cover for storage.

TROUBLESHOOTING

Is there a power failure?
Is the comp / ‘full water’ indicator flashing?
Is the room temperature below the set temperature?
The machine seems to do little.| Is there direct sunshine? (Please put down the curtain.)
Are too many windows or doors open?
Are there too many people in the room?
Is there something in the room producing lots of heat?
The machine seems to do nothing.| Is the filter dusty, contaminated?
Is the air intake or output blocked up?
Is the room temperature below your selected temperature?
Too noisy.| Is the machine positioned unevenly so as to create vibration?
Is the floor underneath the machine uneven?
The compressor does not operate.| It is possible the overheat protection of the compressor is on. Just wait for the temperature to drop?

Error codes for the electrician

Press the ON/OFF button to check, if E5 signal still exists. If that is the case, that meand dthe comprossor system is abnormal.

NOTES ON REFRIGERANT R290

Warning

• The air conditioning system must be kept and transported upright. Otherwise, irreparable compressor damage may occur. Leave the unit for at least 24 hours before putting it into operation.
• Switch off the device and disconnect it from the power supply before cleaning.
• Make sure that the product creates a steady stream of air. Ensure the air inlets and outlets are not blocked.
• To prevent leaks, operate this unit on a horizontal surface.
• Any person performing work on a refrigerant circuit should have a current certificate from an industry-accredited assessment body. This ensures competence for the safe handling of refrigerants according to an industry-recognized assessment specification.
• If the device stops working, dispose of it properly.
• Store the device in a well-ventilated place when not in use.
• Store the device so that it is not damaged.
• Repairs may only be carried out by the manufacturer or an authorized specialist company.
• The cables connected to the device may contain potential ignition sources.
• Do not damage any components of the refrigerant circuit. Escaping refrigerant may not be noticed because it is odourless.
• Maintenance and repairs must be carried out under the supervision of specialists in the use of flammable refrigerants.

Information for rooms with refrigerant pipes

• Limit the piping to a minimum.
• Be careful not to damage the piping.
• Appliances with fl ammable refrigerants may only be installed in a well-ventilated room.
• Comply with national gas regulations.
• All mechanical connections must be freely accessible for maintenance purposes.

CAUTION
Risk of fi re!
This device contains the fl ammable refrigerant R290. If the refrigerant escapes and is exposed to an external ignition source, there is a risk of fi re.

DEVICE CONTROL BY SMARTPHONE

If you integrate the device into your home WiFi, you can conveniently operate it via the associated Klarstein app. The app not only allows you to remotely control the device via your smartphone, but also gives you access to recipes and additional information.
Follow these steps to connect your smartphone to your Klarstein device:

1. Download the Klarstein app first by scanning the QR code with your smartphone (see below), or download it directly from App Store or Google Play.
2. Make sure your smartphone is connected to the same WiFi network that your Klarstein device is to be connected to.
3. Open the Klarstein app.
4. Sign in to your account. If you do not have an account, sign up in the Klarstein app.
5. Follow the instructions from the app.

App Download

Use the scan function of your smartphone to scan the QR code and save the app on your smartphone.

Note: The app provides further information on how to use the app and help on how to connect to your device as soon as you open it for the first time.

https://play.google.com/store/apps/details?id=com.chaltec.klarsteinrn&hl=en

Troubleshooting connection problems
If your Klarstein device cannot be found in the WLAN, check the following:

• Is the device plugged in?
• Is the WiFi feature of my phone enabled?
• Is the WiFi function of the Klarstein device activated? (Follow the instructions in the app)
• Has the WLAN password been entered correctly?
• Are the router, Klarstein device and smartphone in the immediate vicinity during the connection attempt? (Ideally no more than 5 m apart)
• If you have deactivated the 2.4 GHz band in the settings of your wireless router, activate it in your router settings.

Note: For further help, follow the instructions in the app when setting up the connection.

TECHNICAL DATA

Item number| 10034664, 10034665,
10035739, 10035740| 10034666, 10034667,
10035737, 10035738
---|---|---
Power supply| 220-240 V —50 Hz
Power consumption| 1308 W / 6.0 A| 1120 W / 5.1 A
Cooling capacity| 12000 Btu/h —3.4 kW| 10000 Btu/h —2.9 kW
Air volume (max.)| 366 m2/h| 385 m2/h
Moisture removal| 48 L/day| 31.5 L/day
Refrigerant| R290
WiFi standard| 802.11 b/g/n
WiFi frequency| 2,4 GHz
WiFi radio-frequency power (max.)| 20 dBm

PRODUCT DATA SHEET

Information according to regulation (EU) No. 626/2011

10034665,
10035739,
10035740

Inside sound power levels at standard rating conditions on cooling mode in dB: 65 dB
Refrigerant (R290) leakage contributes to climate change. Refrigerant with lower global warming potential (GWP) would contribute less to global warming than a refrigerant with higher GWP, if leaked to the atmosphere. This appliance contains a refrigerant fluid with a GWP equal to 3. This means that if 1 kg of this refrigerant fluid would be leaked to the atmosphere, the impact on global warming would be 3 times higher than 1 kg of CO2
, over a period of 100 years. Never try to interfere with the refrigerant circuit yourself or disassemble the product yourself and always ask a professional.

Energy efficiency ratio (EERrated ): 2,6
Energy efficiency class: A
Energy consumption 1,3 kWh per 60 minutes, based on standard test results. Actual energy consumption will depend on how the appliance is used and where it is located. Cooling capacity Prated in kW: 3,4 kW

Information according to regulation (EU) No. 206/2012

Electricity consumption of single/double duct appliances
(indicate for cooling and heating
separately)| DD: QDD
SD: QSD| 1,3| DD: kWh/a SD: kWh/h
Sound power level| Lwa| 65| dB(A)
Global warming potential| GWP| 3| kgCO2 eq.
Contact details for obtaining more information| Chal-Tec GmbH, WallstraBe 16, 10179 Berlin, Germany.

Information according to regulation (EU) No. 626/2011

Supplier‘s trademark: Klarstein
Supplier‘s model identifier: 10034666, 10034667, 10035737, 10035738

Inside sound power levels at standard rating conditions on cooling mode in dB: 65 dB

Refrigerant (R290) leakage contributes to climate change. Refrigerant with lower global warming potential (GWP) would contribute less to global warming than a refrigerant with higher GWP, if leaked to the atmosphere. This appliance contains a refrigerant fluid with a GWP equal to 3. This means that if 1 kg of this refrigerant fluid would be leaked to the atmosphere, the impact on global warming would be 3 times higher than 1 kg of CO2
, over a period of 100 years. Never try to interfere with the refrigerant circuit yourself or disassemble the product yourself and always ask a professional.

Energy efficiency ratio (EERrated ): 2,6
Energy efficiency class: A

Energy consumption 1,1 kWh per 60 minutes, based on standard test results. Actual energy consumption will depend on how the appliance is used and where it is located. Cooling capacity Prated in kW: 2,9 kW

Information according to regulation (EU) No. 206/2012

Electricity consumption of single/double duct appliances
(indicate for cooling and heating
separately)| DD: QDD
SD: QSD| 1,1| DD: kWh/a SD: kWh/h
Sound power level| LWA| 65| dB(A)
Global warming potential| GWP| 3| kgCO2 eq.
Contact details for obtaining more information| Chal-Tec GmbH, WallstraBe 16, 10179 Berlin, Germany.

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.
This product contains batteries. If there is a legal regulation for the disposal of batteries in your country, the batteries must not be disposed of with household waste. Find out about local regulations for disposing of batteries. By disposing of them in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences.

DECLARATION OF CONFORMITY

Manufacturer:
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.

Importer for Great Britain:
Chal-Tec UK limited Unit 6 Riverside Business Centre Brighton Road Shoreham- by-Sea BN43 6RE  United Kingdom

The complete declaration of conformity of the manufacturer can be found at the following link: use.berlin/10034664

References

• Klarstein | Your home. Your kitchen. Your style.
• Take-e-way GmbH | take-e-back | Elektroschrott Rücknahmesystem Onlinehandel

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>