DRIVEN DRWC4.3 Wireless Reverse Camera Kit Owner’s Manual
- June 5, 2024
- DRIVEN
Table of Contents
DRWC4.3
Wireless Reverse Camera Kit
Installation Instructions | Owners Manual
Due to continuous improvement of the product, specifications are subject to
change without notice.
SPECIFICATIONS
| Monitor Type | 4.3” Anti-glare TFT-LCD |
|---|---|
| Monitor Resolution | 640 x 480 |
| Wireless Range | 150 ft. |
| Camera View Angle | 120* Horizontal |
| Operating Voltage | 12/24V |
| Working Temperature | #NAME? |
| Weather Rating | IP67 |
Congratulations on purchasing the Driven™ DRWC4.3 wireless reverse camera system. This system uses the latest technology available to ensure that it is durable, and reliable and can provide a clear image of the view behind your vehicle while reversing. This product uses the latest digital technology to ensure durability and simple DIY installation.
FEATURES
- 4.3” High Definition TFT LCD Monitor with Anti-glare Shade
- Weatherproof IP67 Reverse Camera with 120 Degree Viewing Angle
- Wireless Camera Uses a Digital Signal that can be transmitted for long distances, Suitable for RV Vehicles
- 12/24V DC Power Supply
Please familiarize yourself with these instructions before starting your installation.
MONITOR INSTALLATION
- Find a suitable location on your dashboard or window screen for your monitor. Please ensure it is in a location where it is easily viewable and does not disturb your vision of the road while driving.
- Clean the location that you have decided to place the monitor to ensure that it is dust and grease-free ( it is recommended to use alcohol wipes to do this)
- Mount the monitor base using the supplied suction cup.
The Monitor is equipped with a cigarette lighter plug that can be easily inserted into the cigarette lighter socket in the vehicle.
STANDARD OPERATION
After the monitor and camera have been successfully installed and paired (if
required), turn the ignition key on ensuring the RED power button on the
monitor cigarette plug is switched on, View the image from the camera on the
monitor. If no image is visible, check all wiring connections are securely
fastened. If the image displays properly, please follow the instructions
below to adjust your screen settings:
WIRELESS CAMERA INSTALLATION INSTRUCTIONS
Thank you for your purchase of the DRIVEN DRWC4.3C wireless camera.
Proper installation of the Camera is critical to the overall view you will be
able to see from your in-cab DRIVEN DRWC4.3M wireless monitor. In most
cases, the rear-view camera mount on an RV is mounted just below the rear top
clearance lights. If your clearance lights are too low, this shouldn’t be a
problem, simply plan for the installation of the camera at the highest point
of the rear outer panel of your RV.
Most modern-day RVs are prewired with a 12v DC power supply cable that is
hidden behind a camera mount cover. If this is the case, simply remove the 4
mounting screws of the pre-mounted base, connect the simple 2 wire red and
black cables to the new harness and replace the complete mount and base with
the DRIVEN DRWC4.3C camera by screwing it down securely with the previously
removed screws.
In the event that your RV or trailer does not come prewired with a 12v DC
power supply at the desired location, you will have to carefully run a power
supply cable to the location on your RV where you wish to mount your camera
system. Plan your wire route for under the RV trailer. Be sure to avoid areas
that could be affected by heat or abrasion. Make sure to properly fuse the
power supply cable at its origin.
Once the camera is powered up, follow the pairing instructions provided with
the DRIVEN DRWC4.3M wireless monitor. Align the camera and test the angle
of the view. Make sure to adjust the angle several times to check your
options. Once you have chosen the specific angle for the camera you are good
to go.
ADJUSTMENT AND CAMERA PAIRING SETTINGS
K1: Brightness adjustment button. Press the K1 button to change the
brightness of the screen, as shown in the image below, press K1 to increase
brightness, once the brightness bar reaches max keep pressing K1 to reset
brightness to 1.
K2: Screen image flipping button. Pressing K2 will cycle the image left,
right, up, and down to match the camera orientation (depends on how you mount
the camera).
K3: Press once to enter camera pairing mode, and the screen will display
as shown below.
After the camera and monitor have been successfully paired, hold the K3 button
for 3 seconds to toggle reversing lines on the screen. This is shown in the
picture:
LIMITED WARRANTY
DrivenTM warrants any products purchased in the U.S.A. from an authorized
DrivenTM dealer.
All Products are warranted to be free from defects in material and workmanship
under normal use and service for a period of one (1) year. This warranty
applies to the original purchaser only.
Driven TM will either repair or replace (at its own discretion) any unit that
has been found to be defective and under warranty provided the defect occurs
within the one (1) year warranty period.
This limited warranty does not extend to units that have been subjected to
misuse, abuse, neglect, or accident. In Driven’s TM judgment, products that
show evidence of having been altered, modified, or serviced without Driven’sTM
authorization, will be ineligible under this warranty. To obtain warranty
service please contact your retailer or visit our
website at www.drivenelectronics.com
Driven is a Registered Trademark of DB Research L.L.P.
Designed and Engineered in the U.S.A.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>