DRIVEN DRWC5CM Wireless Reverse Camera System Instruction Manual
- October 30, 2023
- DRIVEN
Table of Contents
DRWC5CM
5” HD Digital Color Wireless
Monitor and Wireless
Camera System
Installation Instructions
Owners Manual
Due to continuous improvement of the product, specifications are subject to
change without notice.
WWW.DRIVENELECTRONICS.COM
Congratulations on purchasing the Driven™ DRWC5CM wireless reverse camera
system. This system uses the latest technology available to ensure that it is
durable, reliable and can provide a clear image of the view behind your
vehicle while reversing.
This product uses the latest digital technology to ensure durability and
simple DIY installation.
MONITOR SPECIFICATIONS
| Panel: | 5 inch Digital Panel Screen |
|---|---|
| Resolution: | 800*480 |
| Power: | DC12V |
| Storage temperature: | -22 ℉～176 ℉ |
| Working temperature: | -4 ℉ to 158 ℉ |
CAMERA SPECIFICATIONS
| Image Sensor: | 1/3 sensor |
|---|---|
| Effective Pixels: | 720×576 pixel |
| System: | AHD |
| IR Night Vision: | with IR |
| Night vision visible distance: | about 9 ft. |
| Power: | DC 12V & 24V |
| Storage temperature: | -22 ℉～176 ℉ |
| Working temperature: | -4 ℉ to 158 ℉ |
| Operating frequency range Cover: | 2.4GHz~2.4835GHz |
FEATURES
- 5″ High Definition TFT LCD Monitor with Anti-glare Shade
- Weatherproof IP67 Reverse Camera with 120 Degree viewing Angle
- Wireless Camera Uses a Digital Signal that can be transmitted for Long distances, Suitable for RV Vehicles
- 12/24V DC Power Supply
Please familiarize yourself with these instructions before starting your installation.
MONITOR INSTALLATION
- Find a suitable location on your dashboard or window screen for your monitor. Please ensure it is in a location where it is easily viewable and does not disturb your vision of the road while driving.
- Clean the location that you have decided to place the monitor to ensure that it is dust and grease free ( it is recommended to use alcohol wipes to do this)
- Mount the monitor base using the supplied suction cup.
The Monitor is equipped with a cigarette lighter plug that can be easily inserted into the cigarette lighter socket in the vehicle.
STANDARD OPERATION
After the monitor and camera have been successfully installed and paired (if
required), turn the ignition key on ensuring the RED power button on the
monitor cigarette plug is switched on, View the image from the camera on the
monitor. If no image is visible, check all wiring connections are securely
fastened. If the image displays properly, please follow the
instructions below to adjust your screen settings:
ADJUSTMENT AND CAMERA PAIRING SETTINGS
After camera and monitor has been successfully paired, hold the K3 button for 3 seconds to toggle reversing lines on the screen. This is shown in the picture:
K1: In Menu Mode use K1 as UP function, when not in Menu Mode K1 will Turn
on/off Scale Lines.
K2: Press Shortly to enter Menu Mode. Hold for 3 second to confirm Function
selection.
K3: In Menu Mode use K3 as Down Function.
Use the K1 or K3 to choose the PAIRING, PICTURE,MIR-FLIP.
PAIRING: In Menu Mode select Pairing and hold K2 for 3 seconds to confirm
Pairing Mode.
PICTURE: In Menu Mode select Picture and hold K2 for 3 seconds to confirm Picture Image Adjusting.
MIR-FLIP: In Menu Mode select MIR-FLIP and hold K2 for 3 seconds to confirm Image Reverse Mode.
CAMERA INSTALLATION
Proper installation of the Camera is critical to the overall view you will be
able to see from your in-cab DRIVEN DRWC5CM wireless monitor. In most cases
the rear-view camera mount on an RVs is mounted just below the rear top
clearance lights. If your clearance lights are too low, this shouldn’t be a
problem, simply plan to for installation of the camera at the highest point of
the rear outer panel of your RV.
Most modern-day RVs are prewired with a 12v DC power supply cable that hidden
behind a camera mount cover. If this is the case, simply remove the 4 mounting
screws off the pre-mounted base, connect the simple 2 wire red and black
cables to the new harness and replace the complete mount and base with the
DRIVEN DRWC5CM camera by screwing it down securely with the previously removed
screws.
In the event that your RV or trailer does not come prewired with a 12v DC
power supply at the desired location, you will have to carefully run a power
supply cable to the location on your RV were you wish to mount your camera
system. Plan your wire route for under the RV trailer. Be sure to avoid areas
that could be affected by heat or abrasion. Make sure to properly fuse the
power supply cable at its origin.
Once the camera is powered up, follow the pairing instructions provided with
the DRIVEN DRWC5CM wireless monitor. Align the camera and test the angle of
the view. Make sure to adjust the angle several times to check your options.
Once you have chosen the specific angle for the camera you are good to go.
Camera Wiring Connection
CAMERA WIRING CONNECTION
LIMITED WARRANTY
Driven ™ warrants any products purchased in the U.S.A. from an authorized
Driven ™ dealer.
All Products are warranted to be free from defects in material and workmanship
under normal use and service for a period of one (1) year.
This warranty applies to the original purchase only.
Driven ™ will either repair or replace (at its own discretion) any unit that
has been found to be defective and under warranty provided the defect occurs
within the one (1) year warranty period.
This limited warranty does not exted to units that have been subjected to
misuse, abuse, neglect, or accident. In Driven’s ™ judgment, products that
show evidence of having been altered, modified or serviced without Driven’s
authorization, will be ineligible under this warranty.
To Obtain warranty service please contact your retailer or visit our website
at www.drivenelectronics.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>