DRIVEN WH1221Z Remote Control Ambulance User Guide
- June 4, 2024
- DRIVEN
Table of Contents
DRIVEN WH1221Z Remote Control Ambulance
TO START PLAYING
Make sure the ON/OFF switch on the ambulance and remote are on the ON position.
Press button on the ambulance, as indicated then press any button on the remote as indicated.
The ambulance will automatically go into sleep mode after 30 minutes of inactivity to save power. Wake up by pressing button on the ambulance, as indicated.
In case
the ambulance disconnects from the controller, switch the ambulance and the
controller OFF, then switch them back ON again.
Troubleshooting
REPLACING REMOTE CONTROL BATTERIES
REPLACING REMOTE CONTROL BATTERIES
WARNING
This toy produces flashes that may trigger epilepsy in sensitised individuals.
SMALL PARTS CHOKING HAZARD
Not suitable for children under 3 years.
CHOKING HAZARD
Small parts. Not for children under 3 years.
Alignment lever
STEERING ALIGNMENT ADJUSTMENT
If the vehicle does not drive in a straight line, adjust the alignment using the alignment lever. If the vehicle drifts to the left, turn the lever towards the R. If the vehicle drifts to the right, turn the lever towards the L.
- Do not use near seawater or in dirty and dusty environments.
- For indoor play only.
- Do not use in the rain or immediately after rainfall.
- If the ambulance gets wet, open the battery compartment immediately, remove batteries, and turn the ambulance upside down to dry.
- Always clean and dry the ambulance and remote after using outdoors to avoid damage.
- Do not overload the ambulance.
- The remote’s control distance may be reduced when using indoors.
- The ambulance’s remote control may not work after long storage.
- Follow next steps to restart
- Always replace the batteries in the ambulance with 6 new AA alkaline batteries.
- Follow steps 1 and 2 on page to start playing. C.
- If the ambulance does not work, put 2 new AA alkaline batteries in the remote.
BATTERY ADVICE
Requires 6 x AA 1.5V batteries for the ambulance (included). Requires 2 x AA
(1.5V) batteries for the remote control (not included). Non-rechargeable
batteries are not to be recharged. Rechargeable batteries are to be removed
from the toy before being charged. Rechargeable batteries are only to be
charged under adult supervision. Di•erent types of batteries or new and used
batteries are not to be mixed. Only batteries of the same or equivalent type
as recommended are to be used. Batteries are to be inserted with the correct
polarity. Exhausted batteries are to be removed from the toy. The supply
terminals are not to be short-circuited. ATTENTION: When the module’s
functions
lose performance, follow instructions carefully to install new batteries. This
device contains licence exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions: (1) This device may not
cause interference. (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
This device complies with Part 15 of the FCC Rules
Operation is subject to the following two conditions
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Warning
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment. NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>