YANXUAN YX-ETS001 Electronic Toilet Seat Bidet Instruction Manual
- June 5, 2024
- YANXUAN
Table of Contents
ELECTRONIC TOILET SEAT
YX-ETS001
YX-ETS002
Installation Manual
- Thank you for choosing our products. Please read the instructions carefully before installation and keep them available for future maintenance or reference.
- Our company reserves the right of final interpretation for this manual.
The manual is subject to change without notice.
IMPORTANT SAFEGUARDS
When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following:
- The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction.
- Children are being supervised not to play with the appliance.
- This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
- Children shall not play with the appliance.
- Cleaning and user maintenance shall not be made by children without supervision.
READ ALL INSTRUCTIONS BEFORE USING
DANGER –To reduce the risk of electrocution:
- Do not use it while bathing.
- Do not place or store product where it can fall or be pulled into a tub or sink.
- Do not place in or drop into water or other liquid.
- Do not reach for a product that has fallen into the water. Unplug immediately.
- Do not wash the main unit or electrical plug with water or detergent.
- Do not handle the electrical plug with wet hands.
- Do not put a hand or other staff over the outlet of the air dryer or block the outlet of the air dryer.
- Never disassemble, repair, or modify this product.
- During installation, disassembly, repair, and maintenance of the product, the power plug must be switched off and the water supply is shut off.
WARNING– To reduce the risk of burns, electrocution, fire, or injury to persons.
-
Close supervision is necessary when this product is used by, on, or near children or invalids.
-
Use this product only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
-
Never operate this product if it has a damaged cord or plug if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the product to a
service center for examination and repair. -
Keep the cord away from heated surfaces.
-
Never use while sleeping or drowsy.
-
Never drop or insert any object into any opening or hose.
-
Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
-
Connect this product to a properly grounded outlet only. See Grounding Instructions.
-
Do not throw cigarettes and other burning stuff into the toilet, otherwise, it might cause a fire.
-
This product is an electric appliance, so it must be placed far away from water. Please don’t drench urine and other liquid in it.
-
Do not lay on the side or upside the product during the electrical circuit.
-
It is prohibited to use other electric appliances in the same socket.
-
It is forbidden to use the power extension or unstable loose outlet.
-
The old aging water supply hose can not be used, otherwise, it might cause leakage, fire, or electrical shock. Installation of the bidet seat should include specified components and a new water supply hose.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION – Indicates that failure to follow the instruction may cause bodily injury or property damage.
- Do not install or use the product in wet places such as steam rooms etc. This product must be connected to a properly grounded power outlet socket.
- It is recommended to use water-proof electrical outlet which should be installed in the place where is not easily got wet.
- This product should be used with AC 110V-120V, 50/60Hz electrical current only, and load current is at least 15A. The power plug must be equipped with a ground fault circuit interrupter or ground fault electrical leakage protector or similar high sensitive, rapid type leakage switch (Rated sensitive current under 6mA).
- When it thunders, it is strongly recommended to pull out the power plug.
- Do not stand on the ceramic toilet.
- The ceramic toilet must install a floor fixing bolt.
- Do not stand on the product unit, seat, and cover.
- Do not lean against the seat cover when using the product, to avoid damage.
- This product is equipped with a soft-closing seat cover. Heavy pressing or pushing may damage the soft-closing damper.
- Do not use lacquer thinner, petrol, liquid medicine, detergent, insecticide, toilet cleaner, and scrubbing brush to clean the product.
- Exposure to direct sunlight is prohibited.
- Only use tap water or potable water; otherwise, it may cause chafing.
- Do not connect the water supply to the heater outlet. Make sure the inlet water temperature is at 3~35 ℃.
- When the room temperature is under zero degrees, please dry up the water tank, to avoid freezing.
- Raise rest room temperature to prevent the toilet from being damaged due to freezing.
- When moving the product from a cold or wet environment to normal room temperature, wait for 2 hours until the condensation water is fully volatilized. Doing so can prevent the product from electrical short-circuit.
- When not using the product over three(3) days, drain the water out of the container and pull the electrical plug from the wall outlet.
- Stop using the product and shut off the power when the product malfunctions, please contact the service people for professional service.
GROUNDING INSTRUCTIONS
This product should be grounded. In the event of an electrical short circuit,
grounding reduces the risk of electric shock by providing an escape wire for
the electric current. This product is equipped with a cord having a grounding
wire with a grounding plug. The plug must be plugged into an outlet that is
properly installed and grounded.
DANGER – Improper use of the grounding plug can result in a risk of
electric shock.
If repair or replacement of the cord or plug is necessary, do not connect the
grounding wire to either flat blade terminal. The wire with insulation having
an outer surface that is green with or without yellow stripes is the grounding
wire.
This product is factory equipped with a specific electric cord and plug to
permit connection to a proper electric circuit. Make sure that the product is
connected to an outlet having the same configuration as the plug. No adapter
should be used with this product. Do not modify the plug provided — if it will
not fit the outlet, have the proper outlet installed by a qualified
electrician. If the product must be reconnected for use on a different type of
electric circuit, the reconnection should be made by qualified service
personnel.
SAVE THESE INSTRUCTIONS
Technical Specification
| Main Unit | Rating pressure | 110-120V, 50/60Hz |
|---|---|---|
| Rating power | 1050-1240W | |
| Water pressure range | Minimum water pressure 0.07MPa (20L/min. flowing |
pressure).
Maximum water pressure 0.8MPa (Hydrostatic pressure).
Cleaning
device| Electrical wire| length is about 1.2m
Container capacity| 600ml
Heating power| 1000 W
Water temperature| 6 different level adjustment
Water volume| 5 different level adjustment
Cleansing mode| Rear cleaning/Rear massage, Front cleaning for ladies
Spray cleansing location| 5 different level adjustment
Water pressure protector| Pressure stabilize, Automatic pressure discharging
Anti-fouling device| Speedy water discharge device, Anti-syphon device, Anti-
backflow devise, the Filter device
Safety device| Temperature controller, Thermal fuse, Ground protection,
Leakage protection device, Air burning preventer
Drying
device| Warm wind speed| Over 4 m/s
Warm wind temperature| 6 different level adjustment
Heating power| 250W
Safety device| Temperature sensor, Temperature controller,
Thermal fuse
Heated seat| Surface temperature| 6 different level adjustment
Heating power| 50W
Open and close the device| Quiet soft-closing device
Heated burning protection| The seat temperature will automatically lower to
level
1 in 10 minutes after using
Safety device| Seat sensor, temperature sensor, Temperature controller,
Thermal fuse
Intelligent| Night light assembly| Intelligent, often in the off state
Mute setting| Buzzeroff during night
User ID setting| To avoid disturbance from remote controls by multi-user
Packaging List
Remote Control Panel Parts| |
---|---|---
Base Plate Parts| 1. Base plate| 
2. Bolt (2pcs)
3. Flat Washer (2pcs)
4. Plastic Plate (2pcs)
5. Expansion Nut (2pcs)
Water Supply
Assembly| 1. Water Supply Pipe|
2. 3-way Connector
Installtion Manual Warranty
Card Installation paperboard| Installtion Manual| 
Warranty Card
Installation paperboard
Main Unit| |
---|---|---
Main unit identification
Installation instruction
Installation dimension
Note: please check if the installation dimension matches the user’s toilet.
Installation of the mounting plate
Press the expansion nuts into the installation holes in the toilet, then
install the base plate, plastic plates, flat washers, and bolt as per the
drawing and tighten the bolts.
Note:
Unfold the installation paperboard, align the paperboard well fit ceramic bowl
from the tip, and then insert the base plate to the paperboard breach to make
sure the base plate aligns with the paperboard breach.
Installation and disassembly of the main unit
Installation
Push the washlet back onto the base plate until a “click” is heard.
Note:
Before pulling out the washlet, release your hand from the “removal button”.
Disassembly
Press the “removal button” on the washlet, until a “click” is heard, and pull
it out.
Connecting the water supply pipe
- Side inlet: Install the 3-way valve onto the toilet, then attach the water supply hose and the washlet inlet hose to the 3-way valve. Connect the L-shaped end of the water supply hose to the washlet inlet connector.
- Bottom inlet: Connect water supply on the inlet connector, then put supply hose and power line through the relevant holes, finally install seat cover.
Note:
Do not distort or damage the supply hose to avoid any leakage.
Do not use water supply hoses and other accessories of other brands, which may
cause danger.
Do not recommend using our old water supply hose and accessories, which may
cause danger.
Checking the power and water supply
Connect the water supply hose and turn on the angle valve. Check if any
leakage.| Insert the power plug into a power socket.
---|---
| NOTE:
If it’s an electric leakage protection plug, press the protection switch,
indicator Press the electric leakage test button prior to usage, and the
protection switch bounces to show that the protection function works normally.
Press the TEST button (then RESET button) every month to assure proper
operation.
light is on which means there is electricity.
The main unit buzzer rings first “click”, and the power light and energy saver
light will flash.
The power light on and energy saver light off means self-inspection.| The
buzzer rings a second “click” to show that self-inspection is finished.
| 
The water starts to flow into the tank and heating will take 3 minutes.
Function illustration of keys in main unit and actuator
| 
Power| 1. Long press the “Power” button to enter standby mode,
and then quickly press the “Power” button to restore functional mode.
2. When people sit, press the “Power” button to stop the function of rear,
front cleaning, or drying. When no one sits, press the “Power” button to
switch between function mode and power save mode.
---|---|---
Front cleaning
button| When people sit, press the “Front cleaning” button, and it will clean
the front portion of the body; repress the “Front cleaning” button or “Power”
button, and the function will be finished. After a cycle, this function will
be finished automatically, if people keep sitting, it will switch to the
drying function, and will stop after a cycle.
Rear cleaning button| 1. When
people sit, press the “Rear cleaning” button, it will clean the rear portion
of the body; repress the “Front cleaning” button or “Power” button, and the
function will be finished. After a cycle, this function will be finished
automatically, if people keep sitting, it will switch to the drying function,
and will stop after a cycle.
2. When no one sits, press the “Rear cleaning” button, then the wand will
stretch out to clean the nozzle and spray wand.
Remark:
-
When the main unit is in functional mode, the light of power goes on and the energy saver light is off; When in energy save function, the light of power goes off, and energy
saver light is on; When in standby mode, both lights are off. -
The default setting of all functions is on the middle level, after using the remote controller, shift to the level shown on the remote controller.
-
If the product is not used for continual 72 hours, the water in the tank will automatically discharge for 90 seconds and be replaced by fresh water, to avoid bacteria.
Function illustration of keys in remote-control and LCD display instruction
- The operating method of remote control is shown in the instruction manual.
Daily maintenance
Main unit maintenance
- Shut off power supply at maintenance.
- Turn the seat upward open, press down the button located on the right side of the main unit, and pull out the seat. Wipe the stain with a soft damp cloth.
- After cleaning, reinstall the seat back to the main unit.
Note:
Do not pour the water on the product at maintenance.
Spray nozzle maintenance
Do the following to clean the wand.
-
Press the “rear cleaning” button for a while and the wand will come out.
Wipe the wand clean with a soft damp cloth. -
Press again the “stop” or “rear cleaning” button, it will stop the cleaning.
Note:
Do not apply force when pushing or pulling the wand, as this may damage the
mechanism.
Inlet filter cleaning
- Pull out the electrical plug, then shut off the water supply valve and remove the water supply hose.
- Remove the filter. Use the brush to clean the filter.
- Put the filter back into the inlet after cleaning. Then connect the water supply pipe.
Tank anti-freezing and anti-bacterial maintenance
When the room temperature is under zero and electricity is disconnected, or
the user is away for a long time. The water inside the tank should be
discharged.
- Open the tank cover, press the discharge button, and turn on the valve to discharge the water.
- Slightly press the discharge button protruding part to turn off discharging valve and cover.
Note: Before water discharging, the power must be cut off!
Troubleshooting Guide
| Problem | Cause | Solution |
|---|---|---|
| No flushing | Water supply hose buckling causes a block | Solve the buckling |
| The fill valve is off | Turn on the fill valve | |
| The water supply is cut off | Connect the water supply and wait for the water | |
| Poor flushing | Water supply hose buckling causes a partial block | Solve the |
buckling
The fill valve is not fully turned on| Turn on the fill valve fully
The filter is dirty and causes a block| Clean the filter
The water is not hot| The water temperature is set to a normal temperature
level| Reset the water temperature
In standby mode or power save mode| Switch to function mode, and then wash
after 3 minutes
The seat temperature is not hot| The seat temperature is set on a normal
temperature level| Reset the seat temperature
In standby mode| Shift to function mode for 3 minutes
The wind temperature is not hot| The wind temperature is set on a normal
temperature level| Reset the wind temperature
No wind out| In standby mode or power save mode| Shift to function mode to use
dry function
The spray wand cannot retract| Power off| Push back the wand lightly and wait
for the power
Get stuck by impurities| Clear away the impurities
The spray wand cannot stretch out| Power off| Push back the wand lightly and
wait for the power
Do not sit in the sensing area| Sit right in the sensing area
A controller cannot display| Reverse the polarity of the battery| Reload the
battery
Caution| If the problems cannot be solved as per the above methods, please
shut off the power, and contact service providers for maintenance.
If the leakage circuit breaker often trips off, it means the products have
electricity leakage, so please shut off the power, and contact the service
provider for maintenance.
Product Limited Warranty
Model No.| | Customer Name|
---|---|---|---
Seller:| | Purchasing Date:|
Invoice No.| | Customer contact:|
Distributer
Stamp| | Distributer Phone|
Thank you for choosing our product. This product is warranted for one (1) year
since the purchasing date for free repair of problems arising out of defects
in workmanship while using in accordance with the installation manual and
usage cations for intended purposes.
If the product does not work properly during the warranty period, please
contact your nearest service center. This certificate must be presented to
obtain free service under this warranty.
Our company reserves the right to replace the product with other similar
models.
We can serve to fix or repair the product at a reasonable service charge,
after the expiration of the warranty period. Service charges shall be paid
even during the warranty period if breakage or damage is caused by any of the
following events (including but without limitation).
- The user’s negligence or mistake in operation, unreasonable repair, or alteration.
- The product is damaged by negligence or mistake during installation.
- The movement of the installation location of the product.
- Using the product outside of intended use in residential housing or commercial hotels.
- The use of nonspecified power supply (voltage, rating pressure)
- The dirt, sand, and impurities that causing invalid operation.
- Damages due to force majeure (including but not limited to natural disasters) or other incidents.
- The user fails to use in compliance with the warning or caution described in the installation manual.
Remark.
Please fill in the date, and seller correctly. If there are some mistakes, the
warranty will get invalid.
This one-year warranty for free of charge of repair service is only for the
items listed in the warranty.
The purchasing date is subject to the purchasing invoice or receipt.
Please keep this warranty and invoice/receipt available for repair or
maintenance.
Hangzhou Netease Yanxuan Trading Co., Ltd.
Add: Room 410, No. 4 Building, No. 599 Road Wangshang,
Binjiang District, Hangzhou, Zhejiang Province, P.R. China
E-mail:
services.yanxuan@service.netease.com
The picture of the product may not entirely consistent with the actual appearance and color because of product improvement, please in kind prevail.
ASVFAC0428000A-1.3
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>