Hot Wheels Cybertruck User Manual
- June 5, 2024
- HOT WHEELS
Table of Contents
Hot Wheels Cybertruck User Manual
One separate information sheet required: EU DOC
Tesla, Inc., Cybertruck, and all related marks and emblems are intellectual property rights of Tesla, Inc. used under license to Mattel, Inc. Tesla, Inc.,
©2021 Mattel. ® and ™ designate U.S. trademarks of Mattel, except as noted. ®
Operating Frequency:
2420-2465MHZ
Transmitter Power:
ATTENTION :
**CAUTION:**
Surfaces may become hot and cause burns if electronics get wet. To prevent entanglement, keep all hair away from moving parts.
Adult supervision is recommended when the vehicle is being operated.
Keep these instructions for future reference as they contain important information. IMPORTANT: Please read all instructions before operating your vehicle.
The toy is only to be connected to Class II equipment bearing the symbol
1: CONTENTS
- CYBERTRUCK
- CYBERQUAD
- REMOTE CONTROLLER
USB charger not included.
2: FEATURES
A. WORKING HEADLIGHTS
B. WORKING TAILLIGHTS
C. STEERING ALIGNMENT
D. LED INDICATOR
E. ON/OFF SWITCH
F. CHARGER CONNECTOR BOX
G. CHARGE CORD
H. DRIVING CONTROLS
I. LED INDICATOR
J. PAIRING BUTTON
K. BATTERY BOX
3: SET UP
A. REMOTE CONTROLLER BATTERY INSTALLATION
- Unscrew the battery cover with a Phillips head screwdriver (not included).
- Install 2 AA (LR6) 1.5V alkaline batteries (not included) with polarity (+/-) as shown inside the battery compartment. For longer life, use alkaline batteries.
- Replace battery cover and tighten screw.
- Replace batteries in the remote controller if the vehicle does not respond well after a recharge or if you see a red light slowly flashing for approximately 10 seconds in the LED
indicator during play.
Low battery
B. CHARGING THE VEHICLE
**** The vehicle is powered by a permanently installed and non-replaceable
Lithium-ion (Li-ion)
battery, and it must be fully charged before first use.
- Switch off the vehicle by sliding the power switch to OFF (O/ ).
- Unscrew the charger connector box cover with a Phillips head screwdriver (not included).
- Plug the charge cord into a 5V/2A USB charger (not included). The blue LED by the charger connector box will light up when it is connected to a USB charger.
- The blue LED will slowly flash as the vehicle is charging.
- When the vehicle is fully charged, the blue LED will stop flashing and remain on. Unplug the cord when charging is complete. A full charge will take approximately 2-3 hours. Charging time may vary.
- Replace the charger connector box cover and tighten screw.
- Consider recharging the vehicle when the FORWARD/BACKWARD controls on the vehicle become disabled, as this means the battery level is running low. If the vehicle’s headlights suddenly flash for approximately 10 seconds, this means the vehicle’s battery is empty. The vehicle will shut off immediately and must be recharged.
BLUE LED BLINKING
VEHICLE IS CHARGING
BLUE LED ON
VEHICLE IS FULLY CHARGED
TIPS:
- The power switch must be in the OFF (O/ ) position when charging the vehicle.
- The vehicle and remote controller will go into sleep mode if left idle for approximately 5 minutes to preserve battery life. To resume normal play, slide the vehicle’s power switch to OFF then back to ON and move one of the remote controller’s driving controls.
- Charging the battery for more than what is recommended will not give you a longer running time.
- The battery will be hot after play. Wait at least 10 to 15 minutes until the battery cools down before recharging the vehicle.
- It is recommended that you remove all the batteries from the remote controller and leave the vehicle’s battery fully charged but switched OFF before storage.
C. PAIRING THE REMOTE CONTROLLER AND VEHICLE
- Slide the power switch to the ON (I) position on the vehicle.
- Press the pairing button on the remote controller after switching on the vehicle.
- Pairing is complete when the vehicle’s headlights and the remote controller’s lights stop flashing and remain on.
NOTE: If the LED indicator does not stop flashing in approximately 10 seconds, switch off the vehicle, turn it back on, and then press the pairing button on the remote controller to try pairing again.
Pairing
Pairing is complete
D. STEERING ALIGNMENT
- Drive the vehicle forward to see if it is driving straight.
- If the vehicle automatically steers toward the right/left, turn the steering alignment dial on the bottom of the vehicle to the opposite direction until the vehicle goes in a straight line.
STEERING ALIGNMENT
4: HOW TO DRIVE
CHECKLIST
- Is the vehicle’s charger connector box cover closed properly?
- Is the vehicle’s battery fully charged?
- Is the remote controller equipped with fresh batteries?
- Is the remote controller paired with the vehicle?
- Has the vehicle’s steering been aligned?
CONTROLS
NOTE: Operating range of the remote controller is up to 25 m (82 ft).
SKILL CHECK!
Remember, turning directions are flipped on the remote controller when you are driving backward!
CYBERQUAD STORAGE
Load the Cyberquad onto the truck bed!
FOR PRODUCT SOLD IN CANADA
This equipment complies with FCC & Canada radiation exposure limits set forth
for uncontrolled environments.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference. (2) This device must accept any
interference, including interference that may cause undesired operation of the
device.
FOR PRODUCT SOLD IN USA
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.
5: CONSUMER INFORMATION
TIPS & HINTS – FOR ALL DRIVING ENVIRONMENTS
- When your vehicle starts to lose power, it may lose functionality or performance. It’s time for a recharge. For best performance, always start with a fully-charged battery. Your vehicle’s running time may change depending on driving style and driving environment.
- Radio interference can make your vehicle run badly. Interference can be caused by other RC vehicles running on the same frequency, electrical wires, large buildings, CB radios, or other wireless gear. Try to stay away from these!
- Point your remote controller up, and not down toward your vehicle. If your vehicle gets too far away, it won’t work properly.
- Don’t store your vehicle near heat or in direct sunlight. Always turn switches OFF and remove all batteries from the remote controller before storage.
- Don’t drive your vehicle in sand or through water or snow. Do not immerse in water. If your vehicle does get wet, wipe it with a towel and allow to dry completely overnight. If your remote controller is accidentally dropped in water, remove battery(ies) and allow your remote controller to air-dry. Replace with fresh battery(ies) before operation.
- When exposed to an electrostatic source, the remote controller and/or the vehicle may malfunction. To resume normal operation of the remote controller, remove the batteries and reinstall them after 5 seconds. To resume normal operation of the vehicle, turn the power OFF for 5 seconds, then turn it ON again.
- Play safely! Do not drive the vehicle in the street!
SAFETY TIPS
Play safely! Do not drive the vehicle in the street!
- DO NOT pick up the vehicle while in motion.
- Keep fingers, hair, and loose clothing away from the wheels while the vehicle is switched ON.
- Adult supervision is recommended when this vehicle is being operated.
- To avoid accidental operation, remove all batteries from the remote controller when not in use and switch the vehicle OFF before storage.
RECHARGEABLE BATTERY SAFETY INFORMATION
Rechargeable batteries are only to be charged under adult supervision.
- Do not recharge battery if it is hot. Allow it to cool before recharging.
- Do not recharge a battery pack that shows leakage or corrosion.
- Do not disassemble the battery pack. The battery pack is a sealed rechargeable Li-ion battery pack.
- If the battery pack and/or charging port are wet, thoroughly dry before charging.
- Do not recharge non-rechargeable batteries.
- The Li-ion battery in the vehicle is not intended to be replaced or removed by consumers. Before disposal in the waste stream, the Li-ion battery must be removed by a qualified professional and disposed of separately according to local regulations on battery collection and recycling.
- Do not dispose of the batteries in a fire.
BATTERY SAFETY INFORMATION
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage:
- Non-rechargeable batteries are not to be recharged.
- Rechargeable batteries are to be removed from the product before being charged.
- Rechargeable batteries are only to be charged under adult supervision.
- Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.
- Do not mix old and new batteries.
- Only batteries of the same or equivalent type as recommended are to be used.
- Batteries are to be inserted with the correct polarity (+ and –).
- Exhausted batteries are to be removed from the product.
- The supply terminals are not to be short-circuited.
- Dispose of battery(ies) safely.
- Do not dispose of this product in a fire. The batteries inside may explode or leak.
Protect the environment by not disposing of this product or any batteries with household waste. This symbol indicates that this product shall not be treated as household waste. Check your local authority for recycling advice and facilities.
Read More About This Manual & Download PDF:
References
- Anatel — Agência Nacional de Telecomunicações
- Les Jouets Mattel France - Bienvenue sur Les Jouets Mattel
- MATTEL & FISHER-PRICE CUSTOMER SERVICE