MARTEC MFDC133M 52 Fresno Smart WIFI DC Ceiling Fan Installation Guide

Installation Guide

MFDC133M 52 Fresno Smart WIFI DC Ceiling Fan

Thanks for choosing our Fresno DC Smart Series ceiling fan.
We strongly recommend that you read this manual carefully before installation. Models Parameters (Fan Only):
MFDC133M 1320mm 3 Blade DC WiFi Ceiing Fan Matt Black
MFDC133W 1320mm 3 Blade DC WiFi Ceiing Fan Matt White
Part List:

Application

How to Assemble

Remove four screws on the mounting plate as illustrated. Secure the ceiling fan mounting plate to the ceiling using Screws and washers provided. Ensure screws are tightened on the mounting plate.
WARNING Installation MUST carry out by a qualified and licensed electrician. Wire up the receiver with quick connectors and insertinto the mounting bracket, Please make sure the antenna wire has been safely folded inside the canopy cover before final assembly (DO NOT cut the antenna wire)
Important Reminders
Receiver must be correctly installed in the mounting bracket
When the transmitter cannot control the receiver, please check
i) has sufficient battery in the transmitter
ii) any existence of similar remote controlled products nearby that cause interference
Replace battery if getting low as this will affect sensitivity of the transmitter
Take the battery out from the transmitter when leaving used for a long time to avoid battery leaks Isolation switch MUST be connected in the line
WARNING Installation MUST carry out by a qualified and licensed electrician.

How to Install

Carefully install the motor housing into the mounting plate by pushing and twisting and click onto the mounting bracket

How to Install Blades

Install the blades to the bottom of the motor. Tighten and secure blade with screw and washer provided. Repeat this procedure until all blades are installed.
NB: Ensure the blades do not get damaged or bent during the installation process while the fan maybe on the ground, this will affect the performance and balance of the fan and this is NOT covered under warranty. WARNING Installation MUST carry out by a qualified and licensed electrician.

Wire Connections

*6 Year Warranty
Visit our website for details
https://www.martecaustralia.com.au/wp-content/uploads/2023/05/Warranty- Statement_Cooling.pdf
WARNING**

• Installation of fans MUST follow SAA standards and meet local authority regulations.
• Installation MUST be carried out by a qualified and licensed electrician.
• Fanand light MUST be earthed.
• Bracket MUST be firmly attached to a flat solid structure or timber frame.
• DO NOT mix blades from one model to another, all blades MUST be replaced if damaged.
• Thewarranty is VOID if product is not installed according to this installation guide.

Smart Life matching process, please follow the steps:

1. Download the “Smart Life” APP on your smart devices by  scanning the QR code below with camera. https://smartapp.tuya.com/smartlife

2. Turn on WiFi and Bluetooth on your smart devices. Ensu- re it’s connected to a 2.4GHZ WiFi.

3. 0pen the APP, follow the steps to register new user acc-ount or login existing account.

4. Follow instructions in main manual (steps can also be found on the back of the remote) to put the fan into WiFi pairing mode. If the operation is successful, go to step 6.
   If the fan has previously been paired or you can’t get it to work, please go to step 5to RESET the fan.

5. RESET the fan. This step is NOT necessary if the fan hag successfully entered WiFi pairing mode in the last step, if not, try to RESET the fan: turn on the fan, power off after 10 seconds, power on again after 15 seconds, long press “Fan Stop” for 5 seconds, if “beep beep” are heard, the reset is successful. If “beep beep” is not heard, the reset is failed, please repeat this step.

6. 0nce the fan has entered WiFi pairing mode, open the APP again on the smart device. Click “Add Device” in the middle or the “+” on the top right of the screen.

7. The auto scan should begin automatically. and the fan should show up at the top of screen within a few seconds.
   Note: If the fan is not showing up, you can add it manually  by clicking and navigate to: >Add Manually >Small Home Appliance > Fan

8. Follow instructions in the APP to finish the set up.

WiFi / Remote Control Pairing

Fan only model
Pairing the remote control

1. Turn on the ceiling fan.
2. Within the first 20 seconds, continue pressing the button until you hear a “beep” sound. ie. It is paired.
   If you don’t hear a “beep” sound, repeat step 1 and step 2 again.

Entering WiFi Pairing mode:

1. Turn on the power.
2. Within the first 20 seconds, press and hold the “ “button until a “beep” is heard.
3. Continue step connect on your smart devices to complete the pairing.
   If you don’t hear a “beep” sound, repeat the above steps.

FAN OFF : to switch off the fan.
SLEEP MODE : Turn on the fan at an extra lower speed to create a general breeze.
SPEED BUTTON: 1 = lowest speed. 6 = highest speed.
NATURAL WIND MODE : designed for the elderly and children. 1-6 speed changes randomly to feel the breeze.
FORWORD AND REVERSAL : summer/winter reverse mode.
TIMER 1H/4H/8H: preset timer for fan and light to stop automatically. ie. if timer set at 1H and then press 4H, fan will stop at 4H. Setting default to last press.
WIFI BUTTON : Follow the instructions and press and hold for 20 seconds to enter wifi matching mode.

Fan LED Light Model
Pairing the remote control

1. Tur on the ceiling fan.
2. Within the first 20 seconds, continue pressing the button until you hear a “beep” sound. ie. It is paired.
   If you don’t hear a “beep” sound, repeat step 1 and step 2 again.

Entering WiFi Pairing mode:

1. Turn on the power.
2. Within the first 20 seconds, press and hold the “ ” button until a “beep” is heard.
3. Continue step connect on your smart devices to complete the pairing.
   If you don’t hear a “beep” sound, repeat the above steps.

FAN OFF : to switch off the fan.
SLEEP MODE : Turn on the fan at an extra lower speed to create a general breeze.
SPEED BUTTON: 1 = lowest speed. 6 = highest speed.
NATURAL WIND MODE : designed for the elderly and children. 1-6 speed changes randomly to feel the breeze.
FORWORD AND REVERSAL : summer/winter reverse mode.
TIMER 1H/4H/8H: preset timer for fan and light to stop automatically. ie. if timer set at 1H and then press 4H, fan will stop at 4H. Setting default to last press.
LIGHT ON/OFF : to switch off the light.
CCT : warm white (2700K) / netural white (4000K) / cool white (6500K)
LED- LED+: minus “-” = reduces brightness plus “+”= increases brightness
*6 Year Warranty
Visit our website for details
https://www.martecaustralia.com.au/wp-content/uploads/2023/05/Warranty- Statement_Cooling.pdf
WARNING**
Installation of fans MUST follow SAA standards and meet local authority regulations.

• Installation MUST be carried out by a qualified and licensed electrician.
• Fanand light MUST be earthed.
• Bracket MUST be firmly attached to a flat solid structure or timber frame.
• DO NOT mix blades from one model to another, all blades MUST be replaced if damaged.
• Thewarrantyis VOID if product is not installed according to this installation guide.

E: sales@martecltd.com.au 
P: 02 8778 7500
www.martecaustralia.com.au

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>