BRESSER F004514 Radio Remote Control for LED Photo Studio Lamps Instruction Manual
- June 5, 2024
- BRESSER
Table of Contents
BRESSER F004514 Radio Remote Control for LED Photo Studio Lamps
GENERAL WARNINGS
DANGER OF AN ELECTRIC SHOCK!
-
This device contains electronic parts that are powered by a power source (batteries).
-
Only use the device as described in the manual. Otherwise, you run the DANGER of an
-
ELECTRIC SHOCK.
-
Never attempt to operate a damaged device, or a device with damaged electrical parts!
-
Damaged parts must be replaced immediately by an authorized service agent.
-
Operate the device only in a completely dry environment and do not touch the device with wet or damp body parts.
-
Do not expose the device to high temperatures.
-
Do not short-circuit the device or dispose of in fire! Excessive heat and improper handling can cause short circuits, fires and even explosions!
-
Only use the recommended batteries1!
-
IMPORTANT NOTE!
-
Do not disassemble the device! In the event of a defect, please contact your dealer. They will contact the Service Center and can arrange the return of this device for repair if necessary.
-
Do not subject the device to excessive vibrations.
PARTS LIST & DELIVERY CONTENT
PARTS LIST
- (-) Button
- Decrease & Selection
- ( ) Power Button:
- Power ON/OFF & Confirmation
- (+) Button
- Increase & Selection
- (=) Menu
- Power Output, Colour Temperature, Channel selection
DELIVERY CONTENT
2.4G Wireless Remote Controller (1x)
POWER SUPPLY
NOTE: This device is powered by 2 pcs. AAA Batteries.
INSTALLING THE BATTERIES
Open the battery compartment and insert 2 pcs. AAA batteries. Please make sure that the + and – polarity is correct. Remove the batteries if you don’t use the remote for a long time.
OPERATING AND USING THE DEVICE
POWER ON/OFF
- Press the ( ) Power button to switch the unit ON.
- Long press the ( ) Power button to switch the unit OFF.
CYCLE THROUGH THE MENU
- Press the (=) Menu button to cycle through the menu.
- Press 1x = shows 10 “power output” 10 = 10%
- Press 2x = shows 56 “color value” 56 = 5600 K
- Press 3x = shows 01 “channel” 01 = Channel 1
SELECT THE CHANNEL
- Press the (=) Menu button 3 times to go to the channel menu.
- Press (+) or (-) to choose your desired channel.
- Press the (=) Menu button to confirm your selection.
TURN ON LIGHT
ADJUSTING THE POWER LEVEL/BRIGHTNESS
The light is on power 10%
Press (+) or (-) to increase or decrease the light power.
ADJUSTING THE COLOUR TEMPERATURE
TURN OFF LIGHT
DISPOSAL
Dispose of the packaging materials by type. Contact your local waste-disposal service or environmental authority for information on the proper disposal. Do not dispose of electronic devices in the household garbage! According to the European Directive 2002/96/EU on Waste Electrical and Electronic Equipment and its transposition into national law, used electrical equipment must be collected separately and recycled in an environmentally sound manner. Observe the current legal regulations when disposing of the device! Information on proper disposal can be obtained from municipal waste disposal service providers or the Environmental Agency.
CLEANING
Before cleaning the device, disconnect it from the power supply (remove batteries)! Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any cleaning fluid Protect the device from dust and moisture. Store it in the supplied bag or transportation packaging. The batteries should be removed from the unit if it has not been used for a long time.
EC DECLARATION OF CONFORMITY
A “Declaration of conformity” in accordance with the applicable directives and corresponding standards has been prepared by Bresser GmbH. This can be viewed at any time upon request at www.bresser.de/download/F004514/CE/F004514_CE.pdf
UKCA DECLARATION OF CONFORMITY
A “Declaration of conformity” in accordance with the applicable directives and corresponding standards has been prepared by Bresser GmbH. This can be viewed at any time upon request at www.bresser.de/download/F004514/UKCA/F004514_UKCA.pdf
TECHNICAL DATA
GUARANTEE
The regular warranty period is 5 years and begins on the day of purchase. You can consult the full guarantee terms as well as information on extending the guarantee period and details of our services at www.bresser.de/warranty_terms
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>