ECCO EC5605-WK Wireless Camera or Monitor System Instruction Manual

ECCO EC5605-WK Wireless Camera or Monitor System

IMPORTANT:  Read all instructions before installing and using. Installer: This manual must be delivered to the end user.

WARNING: Failure to install or use this product according to the manufacturer’s recommendations may result in property damage, serious injury, and/or death to those you are seeking to protect!

Do not install and/or operate this safety product unless you have read and understood the safety information contained in this manual.

1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to ensure the safety of emergency personnel and the public.
2. Emergency warning devices often require high electrical voltages and/or currents. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing, which can cause personal injury and/or severe vehicle damage, including fire.
4. Proper placement and installation is vital to the performance of this warning device. Install this product so that output performance of the system is maximized and the controls are placed within convenient reach of the operator so that they can operate the system without losing eye contact with the roadway.
5. It is the responsibility of the vehicle operator to ensure daily that all features of this product work correctly. In use, the vehicle operator should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors), people, vehicles or other obstructions.

IMPORTANT: Occasionally, a few highlights or dark spots may occur on the LCD screen. This is a very common phenomenon in active matrix display technology and doesn’t necessarily indicate any defects or faults. Never try to repair this device by yourself. In case of any problems, please turn off the display at once and notify our company or an authorized dealer. The monitor is a complex device. Any disassembly or modification may lead to damage and void the warranty.

Precautions

Storage and Keeping

1. Do not expose the monitor to excessive heat or cold.
2. Never use this device in environments with excessive moisture, dust or smoke.
3. Avoid dropping or striking this device.
4. Never puncture, scratch or use abrasive cleaning materials on this device.
5. Do not place cables where they may be pinched or stepped on.
6. Leave at least a 2” space between the monitor and walls or other objects to allow adequate air circulation around the device.
7. The monitor is not designed to be waterproof.

Operating Precautions

1. The device may be powered by a 12 or 24 volt automotive battery or vehicle electrical system.
2. Make sure all cables are connected properly. Observe polarity. Improper cable connections may damage the monitor. The camera and monitor do not require a constant 12 or 24 volt. They may be connected to an ignition power source.

Maintenance

1. Disconnect power from the monitor before cleaning the device.
2. Use a mild household detergent and clean the unit with a slightly damp, soft cloth. Never use strong solvents such as thinner or benzine, as they might damage the finish of the device.

WARNING: To prevent accidental shock, DO NOT OPEN THE MONITOR CASE. Opening the monitor case will expose the inside of the monitor to conditions that could adversely affect performance. Any evidence of tampering with sealed components will void the warranty.

Features

1. TFT LCD monitor with wide angle view and high-resolution display.
2. Picture image may be adjusted for Horizontal, Vertical, Mirror, and Normal viewing.
3. Supports multiple image display modes like single, dual, quad, and H-split
4. Select from 8 languages for user operation.
5. Automatic backlighting for buttons.
6. Full-function remote control.
7. Multiple video formats: PAL/AUTO/NTSC.
8. Up to 4 wireless camera inputs, 1 video output and 1 audio output.
9. Supports 12V or 24V vehicle systems.
10. On-board speaker.
11. Automatic scanning function.
12. The scale can be adjusted for left, right, up and down.
13. Automatically switches to back-up, left, right, or front camera views.

Camera Installation

NOTE: Before installing the system, pair all cameras to the monitor. See PAIRING section on page 8. The camera and monitor will need 12 or 24 volt supplied to them for the pairing process.

Important:  Mount the camera at a location that provides the best view of the area immediately behind the vehicle. Generally, mounting locations toward the top of the vehicle provide the best field of view. Lower mounting locations reduce the field of view and increase the likelihood of damage from road spray.

1. Find an appropriate location for installation.
2. Drill holes according to the size of the U-bracket and fix the U-bracket.
3. Drill a 3/4” (19mm) hole next to U-bracket.
4. Install the camera on U-bracket.
5. Connect the power leads to 12 or 24 volts as shown in Figure 2.
6. Loosen the hex head screws and adjust the camera’s position to get the best view angle in the monitor as shown in Figure 1.

Wiring

Important:  Waterproof all connections whether inside or outside the vehicle by using sealant and wrapping with insulation tape. Wrap tape tightly, overlapping by one-half widths so there are no gaps.

Single red wire to positive power supply of DC/12 or 24 volt using a 3A fuse. Single black wire to GND.

Optional Trigger Wires (see Figure 3)

1. The monitor can be manually switched between all 4 cameras using the “S” button or the “SEL” button on the remote.
2. The trigger wires can be used to automatically display any of the cameras. The brown (CAM 4) trigger wire has the highest priority
   since it is the default reverse camera. This is a safety feature so when the vehicle is in reverse, only CAM 4 can be displayed. Trigger wire priority can be changed in the settings. See Trigger options on page 10.

The trigger wire priority is as follows:

• Brown wire (CAM 4)
• Blue wire (CAM 2)
• White wire (CAM 1)
• Green wire (CAM 3)

1. | Red| Power 12 or 24 VDC

2. | Black| Ground

3. | Brown| Cam 4 trigger wire

4. | Blue| Cam 2 trigger wire

5. | White| Cam 1 trigger wire

6. | Green| Cam 3 trigger wire

7. Standby state – To put the display into standby state, press the power button on the display. This will turn the display off but will turn the monitor on when a trigger wire is activated.

Reversing Display

1. When the white wire is connected to positive, the monitor automatically switches to CAM1.
2. When the blue wire is connected to positive, the monitor automatically switches to CAM2.
3. When the brown wire is connected to positive, the monitor automatically switches to CAM4 (back-up camera). The reverse scale, if enabled, will display.
4. When the brown trigger wire is engaged (reversing camera) the camera view cannot be changed until the vehicle is out of reverse.
5. When the green wire is connected to positive, the monitor automatically switches to CAM3.

Bracket Installation

Installation instruction of using U-support bracket

1. Select the suitable position on the vehicle and fix the U-support bracket with screws (Figure 4)
2. Fix the monitor to the U-support bracket with angle adjustment screws and adjust the view angle of the monitor (Figure 5)
3. Connect the monitor to the included harness.

Base Support Installation (Pedestal Mount)

1. Select suitable position on vehicle and fix the base support. (Figure 6)
2. Fix the monitor to the base support and adjust the view angle. (Figure 7)
3. Connect the monitor with the AV and power supply cable (Figure 8)

Remote Control Operation

Important

1. Never disassemble the remote control or allow it to drop, or become wet.
2. Press the control button firmly. Allow 2 seconds for the picture to change.

• MUTE (Mute): Press to select MUTE or enable sound.
• POWER (Power switch): Press to turn on/off the monitor.
• OK: Press OK button to enter the menu item or save user settings.
• MENU: Press to show menu or exit menu.
• VOL-: Volume decrease and menu selection left.
• VOL+: Volume increase and menu selection right.
• SEL: Jump key selector. Fast jump to the display mode specified by SYSTEM SETUP – JUMP KEY.
• PAIR: Fast pairing when the camera is activated.
• MIR: MIR-Flip selection.

Menu

Press the MENU button either on the remote control or monitor screen to display the following options: Audio Source, Mode, Pairing, Settings, Power. To navigate MENU, press the ‘+’ or ‘-’ button on the monitor or VOL+/- on the remote control to select the sub-menu. Press the down arrow on the monitor or ‘OK’ on the remote control to enter the sub-menu. Press the‘ MENU’ button again to exit the menu and save settings.

Main Menu

• Press the M’ button on the monitor or ‘menu’ button on remote control to show the menu
• Press the +’ or ‘- ‘button on the monitor or VOL +/- on the remote control to select sub-menu
• Press the button on the monitor or ‘OK’ on remote control to enter sub-menu
• Press the menu button again to exit the menu with settings saved

Audio

• Select the channel that you want to hear the audio under split view mode
• Press the‘ +’ or ‘- ‘button on the monitor or VOL +/- on the remote control to switch option
• Press (down arrow) on the monitor or ‘OK’ on the remote control to select the channel and exit the menu.

Mode

• Select display mode, which is auto-scan, which automatically switches channels in the circle from channel 1 through
• Press the‘ +’ or ‘- ‘button on the monitor or VOL +/- on the remote control to switch the option.
• Press (down arrow) on the monitor or ‘OK’ on the remote control to select the channel and exit the menu.

Pairing

• Pairing Camera: select the channel you want to pair.
• Press the +’ or ‘- ‘button on the monitor or VOL +/- on the remote control to switch options.
• Press the button on the monitor or ‘OK’ on remote control to start pairing.

When pairing is in process, there will be a pairing icon on top of the correspondent channel. The pairing icon will be replaced with a check mark when the pairing is successful. If no camera pairs successfully in 20 seconds, the pairing icon will disappear and the pairing process will stop. Delete Camera: remove the camera that is already paired in the selected channel.

Settings

Please note that these parameters can only be adjusted when the camera is connected to the correspondent channel

To select a channel, press the ‘M’ button on the monitor or ‘Menu’ on the remote control. When the icon background turns green, press the ‘+’ or ’-’ button on the monitor or VOL +/- on the remote control to switch to the channel you want to set

• Press the button on the monitor or ‘OK’ on remote control to enter the channel’s parameter.
• Press the +’ or ’-’ button on the monitor or VOL +/- on the remote control to select the parameter to change. A GREEN outline will show on the currently selected parameter.
• Press the button on the monitor or ‘OK’ on remote control to select the current parameter. When the outline turns RED, Press (or long press) the ‘+’ or ’-’ button on the monitor or VOL +/- on the remote control to adjust the value, press button on the monitor or ‘OK’ on the remote control, cursor return to green and confirm the setting.
• Press the M’ button on the monitor or ‘Menu’ on remote control to return to the select channel
• Press ‘M’ on the monitor or ‘menu’ on remote control to save and exit the menu

The dimmer value can be adjusted when Auto is off Select to set day and night dimmer values for when Auto is on.

• Day: adjust the panel brightness in normal light conditions
• Night: adjust the panel brightness in low light conditions

Currently displayed channels are indicated by green lettering. The new selection is indicated by a green background.
Press the +’ or ’-’ button on the monitor or VOL +/- on the remote control to select which channel to display in the dual view.
Press the button on the monitor or ‘OK’ on remote control to save the selection

Same way of operation as Dual View

• Trigger Delay: the setting range is 1-60 seconds. The trigger delay indicates how long it will take after the trigger wire is disconnected before the monitor goes back to the original view.
• Priority: the setting range is 1-4.

Auto scan duration range is 5-60 seconds. The duration indicates how long a camera view will be shown when the monitor is set to auto scan, before cycling to the next camera view. Each camera view can be turned on or off to be included or removed from the auto scan rotation.

Select the view you want to show upon power on

• Start auto scan upon power on
• Enter standby mode (black screen) upon powering on

The icon in green is the one currently selected.

• Press the +’ or ’-’ button on the monitor or VOL +/- on remote control to switch options.

• Press button on the monitor or ‘OK’ on the remote control to cancel option, the icon turns white if option is canceled, when all options are white, the monitor will show the picture from the last time when it was powered off.

• Press ‘M’ on the monitor or ‘menu’ on remote control to save and exit the menu.

• If set on, show reverse label upon triggering the correspondent channel.

• Enter the setting to move the label.

• Press the +’ or ’-’ button on the monitor or VOL +/- on the remote control to move the label right or left.

• Press the +’ or ’-’ button on the monitor or VOL +/- on the remote control to move the label up or down.

• Press the‘ +’ or ’-’ button on the monitor or VOL +/- on the remote control to adjust size of the label

• Press button on the monitor or ‘OK’ on remote control to switch mode

Specifications

CAMERA SPECIFICATIONS / FEATURES

Image Device| 1/3” CMOS
Ingress Protection| IP69K
Night Vision| 11 IR LEDS = MAX. 10M Distance
TV System| NTSC / PAL
Effective Pixels| 728 x 488
Sensing Area| 4.6228mm x 3.6112mm
Video Output| 1.0VP-P, 750OHM
S/N Ratio| Better Than 48dB
White Balance| Auto
Current Consumption| Max. 0.5 A
Lens Angle| 120°
Voltage| 12 or 24 volt

MONITOR SPECIFICATIONS / FEATURES

Product| 5.6 inch HD 2.4GHz Digital Wireless Vehicle Quad-view Monitor
Resolution| 640 x 3 (RGB) x480
Contrast| 800:1
Brightness| 600cd/m2
Operation Freq.| 2400-2483.5MHz
Range| 984 feet / 300 meters
Receiving Sensitivity| -78dBm
RF Band Width| 5MHz
Speaker| Yes
Voltage Range| 12 or 24 volt
Power Comsumption| 5W
Monitor Dimension| 6.32”(W)x4.51”(H)x1.06”(D)
Operating Temp| -20° C to 70°C/-4°F to 158°F
Storage Temp| -30°C to 80°C/-22°F to 186°F

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. this device must accept any interference received, including interference that may cause undesired operation.

NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Manufacturer Limited Warranty and Limitation of Liability

Manufacturer warrants that on the date of purchase, this product will conform to the Manufacturer’s specifications for this product (which are available from the Manufacturer upon request). This Limited Warranty extends for Twelve (12) months from the date of purchase.

DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED MODIFICATIONS, FIRE OR OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING MAINTAINED IN ACCORDANCE WITH THE MAINTENANCE PROCEDURES SET FORTH IN THE MANUFACTURER’S INSTALLATION AND OPERATING INSTRUCTIONS VOIDS THIS LIMITED WARRANTY.

Exclusion of Other Warranties

THE MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED. THE IMPLIED WARRANTIES FOR MERCHANTABILITY, QUALITY OR FITNESS FOR A PARTICULAR PURPOSE, OR ARISING FROM A COURSE OF DEALING, USAGE OR TRADE PRACTICE ARE HEREBY EXCLUDED AND SHALL NOT APPLY TO THE PRODUCT AND ARE HEREBY DISCLAIMED, EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT DO NOT CONSTITUTE WARRANTIES.

Remedies and Limitation of Liability

MANUFACTURER’S SOLE LIABILITY AND BUYER’S EXCLUSIVE REMEDY IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR UNDER ANY OTHER THEORY AGAINST THE MANUFACTURER REGARDING THE PRODUCT AND ITS USE SHALL BE, AT THE MANUFACTURER’S DISCRETION, THE REPLACEMENT OR REPAIR OF THE PRODUCT, OR THE REFUND OF THE PURCHASE PRICE PAID BY BUYER FOR NON-CONFORMING PRODUCT. IN NO EVENT SHALL THE MANUFACTURER’S LIABILITY ARISING OUT OF THIS LIMITED WARRANTY OR ANY OTHER CLAIM RELATED TO THE MANUFACTURER’S PRODUCTS EXCEED THE AMOUNT PAID FOR THE PRODUCT BY THE BUYER AT THE TIME OF THE ORIGINAL PURCHASE. IN NO EVENT SHALL THE MANUFACTURER BE LIABLE FOR LOST PROFITS, THE COST OF SUBSTITUTE EQUIPMENT OR LABOR, PROPERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES BASED UPON ANY CLAIM FOR BREACH OF CONTRACT, IMPROPER INSTALLATION, NEGLIGENCE, OR OTHER CLAIM, EVEN IF MANUFACTURER OR A MANUFACTURER’S REPRESENTATIVE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE MANUFACTURER SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY WITH RESPECT TO THE PRODUCT OR ITS SALE, OPERATION, AND USE, AND THE MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES THE ASSUMPTION OF ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH PRODUCT.

This Limited Warranty defines specific legal rights. You may have other legal rights which vary from jurisdiction to jurisdiction. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages.

CONTACTS

• 833 West Diamond St, Boise, Idaho 83705
• Customer Service USA: 800-635-5900UK
• +44 (0)113 237 5340
• AUS +61 (0)3 63322444
• ECCOESG.com

An ECCO SAFETY GROUP™ Brand

ECCOSAFETYGROUP.com

© 2013 ECCO, Inc. All rights reserved.

References

• Home - ECCO
• Home - ECCO Safety Group

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>