KLARSTEIN 10035818 Skytower 360 Degree Smart Air Cooler Instruction Manual

SKYTOWER 360°

SMART

Air Cooler

10035818

www.klarstein.com

Dear Customer,

Congratulations on purchasing this device. Please read the following instructions carefully and follow them to prevent possible damages. We assume no liability for damage caused by disregard of the instructions and improper use. Scan the QR code to get access to the latest user manual and more product information.

TECHNICAL DATA

SAFETY INSTRUCTIONS

• Check the voltage on the rating plate before use. Only connect the appliance to sockets which correspond to the voltage of the appliance.

• Keep the appliance and cable away from sources of heat, sharp objects or anything that may cause damage.

• Do not place the cord under carpets. Do not cover the cord with small clothes, shirts or other similar elements. Place the cord away from traffic areas in order to avoid any risk of tripping over.

• Do not operate the appliance if the cable or plug is damaged.

• If the supply cord or plug is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• Indoor use only.

• Do not cover the machine during using.

• Place the appliance on a stable flat horizontal surface. Make sure the appliance is in an upright position during use.

• Ensure the appliance is switched OFF before connecting to the mains power supply.

• Always ensure that hands are dry before operating or adjusting any switch on the product or touching the plug and mains supply connections.

• Do not leave this appliance unattended when it’s in use. Turn off and disconnect the appliance when you leave the room for an extended period.

• Switch off the appliance and unplug from the mains socket when not in use, before filling, cleaning or other maintain.

• To disconnect the appliance, switch it “OFF”, and then remove the plug from outlet. Do not pull the cord to disconnect the plug.

• This device may be only used by children 8 years old or older and persons with limited physical, sensory and mental capabilities and / or lack of experience and knowledge, provided that they have been instructed in use of the device by a responsible person who understands the associated risks.

• Use the appliance only as described in this manual.

• Do not insert your fingers in the openings of the guard.

• Do not leave hair, tissue, tablecloths, clothes or curtains near all openings of the fan, they could be sucked into the fan and be taken within the internal moving parts that could cause injury or damage.

• Do not use the appliance in wet or damp locations such as bathrooms.

• Do not operate the appliance when it’s not mounted on its wheels or if it’s lying on the side.

• Make sure the cord is completely extended before use.

• When in operation, evaporative coolers moisturize the ambient air. Over-humidification of residential rooms should be avoided. Recommendation: 40-50 % relative humidity. Excessive humidity of the air can damage the home and cause health problems.

• The appliance may only be set up on water- and moisture-proof flooring materials (spilling some drops of water is unavoidable when the content of the tank is changed).

• With each and every change of tank content, completely remove residual water from the equipment. To prevent nucleation, remove residual water from the equipment and water tank every time after three days of use.

PRODUCT FEATURES

• On/Off: Separate ON/OFF button

• Fan speed: 3 speed levels: Low, Medium and High

• Wind modes: Normal, Natural wind and Sleep wind

• Wind direction: Automatic swing of horizontal louvers and vertical louvers

• Time until automatic switch-off: 1-9 hour timer without accumulation (timer tolerance in the 3 % range).

• Water pump for cooling/air humidification

• Touch button control

• Dry wind function and automatic dimming of LED lighting if no button is pressed within one minute

• Remote control function (with IR distance greater than or equal to 6 meters)

• Easy to clean water tanks

• Spray water circulation cooling technology, with large water circulation and faster cooling

DEVICE OVERVIEW

1

| Front case|

6

| Rear case

2

| Display panel|

7

| Rear grille

3

| Horizontal blade|

8

| Winding frame

4

| Decoration panel|

9

| Power cord

5

| Base|

10

| Water tank

Note on using the water tank

In principle, you can use your air cooler at any time without water in the tank. It will then work like a normal fan. Water in the tank is only needed for the cooling function. The air cooler evaporates this through the nebulizer flow, removing heat from the air and reducing the air temperature of the fan by up to 3 °C, depending on the coldness of the water used. We advise against using the cooling function on days with particularly high humidity, as it increases this further and can thus contribute to circulatory problems.

ACCESSORIES

Remote control

| Ice box
---|---
|

Use of the remote control

1. Open battery cover in the rear of remote control and install a 3 V CR2032 battery for use. To open the battery compartment, press down the cover in the direction of the arrow (1) and pull out the battery compartment in the direction of the arrow (2).
2. Point the remote control at the receiver during use.
3. Replace flat batteries. When inserting the new battery, make sure that the polarity (+/-) is correct. Then put the battery compartment back into the remote control.

Use of the ice box

1. Place the ice box in the freezer compartment until it is completely frozen.
2. Place the ice box in the water tank of the appliance. Within 10 min after placing the ice container, the temperature in the water tank is reduced below ambient temperature.
3. Two ice boxes are included in the delivery. Use them alternately.
4. It is forbidden to open the cover of the ice boxes. Never swallow the contents of the ice boxes.

Note: With specific cold storage and insulation features, the ice box can slowly absorb the heat in the water to keep temperature in the water tank lower than ambient temperature for hours all the time, thus producing more nice and cool wind by the air conditioner fan.

CONTROL PANEL AND REMOTE CONTROL

Control panel (buttons)

| | | | | |
ON/OFF| Swing function (Left-Right)| Swing function (Up-Down)| Wind speed| Timer| Wind mode/WIFI|

Cooling/ humidification mode

Remote control (buttons)

1 Timer
2 Screen off
3 Wind mode
4 Cooling/humidification mode
5 Wind speed
6 Swing function (Up-Down)
7 Swing function (Left-Right)
8 ON/OFF

DISPLAY INDICATORS

1

| ON/OFF|

7

| Natural wind mode

2

| Swing function (Left-Right)|

8

| Sleep wind mode

3

| Swing function (Up-Down)|

9

| Cooling/humidification mode

4

| Negative ion function|

10

| WIFI function

5

| Display window|

11

| Timer

6

| Wind speed| |

COMMISSIONING AND OPERATION

Before use

• Remove the appliance from its packaging and remove all packaging materials.
• Place the appliance on a stable and level surface.
• Insert the mains plug into the socket. The appliance can then be used directly and no installation is required.

Commissioning

When the appliance’s mains plug is plugged into the socket for the first time, the appliance beeps twice and goes into standby mode. All indicator lights are off. Except for the ON/OFF button, all buttons are inactive.

Switching appliance on/off

If you press the ON/OFF button in standby mode, the appliance is switched on. When the appliance is switched on for the first time, the appliance runs at low speed in normal wind mode. When the appliance has been switched off and you switch it on again, the mode used before switching off is restored. This does not apply to the timer setting. If the sleep wind mode was set before switching off, this is not saved. When the appliance is switched on again, it will run in normal wind mode.

If no button (including remote control buttons) is pressed within one minute during operation, all light indicators are dimmed to 30 % of their original brightness. Press the desired button again to restore the brightness and perform the respective function.

To switch off the appliance, press the ON/OFF button again. The appliance will beep once. When the appliance has been switched off, it goes into standby mode and the light indicators and screen go out.

Swing function

In the power-on state, press the left-right swing button to switch on/off the left-right swing function, and the corresponding LED indicator (2) will show its working state.

In the power-on state, press the up-down swing button to switch on/off the up- down swing function, and the corresponding LED indicator (3) will show its working state.

The left-right swing mode works as follows: the swing head swings left and right at an 80° angle. When switching the direction, the swing head will pause for 1 second and then swing to the other direction.

When turning on the up-down swing function after it is first powered on, the motor will find the original point first .The horizontal blades may be closed for about 10 seconds and then swing upwards to open. This is a normal phenomenon.
When the up-down swing button is off, the horizontal blade will swing to the horizontal position and stop.

Setting the speed

The speed button can be used to adjust the wind speed. Pressing the speed button several times cycles through the speed levels in the following order:
Low > Medium > High > Low.

The speed levels are displayed in numbers on the screen:

Dry wind function

If you press and hold the speed button for 3 seconds, the dry wind function is started. The appliance is running at high wind speed and the screen shows “3” and the indicator flashes for 20 minutes.
While using this function, all buttons except the ON/OFF button are inactive. Press and hold the speed button for 3 seconds to cancel the function.
When the dry wind function has been activated for 20 minutes, the appliance automatically switches off and goes into standby mode.

Setting the timer

The timer button can be used to set the time until the appliance switches off automatically. You can set a time between 0-9 hours. The time until automatic switch-off can be adjusted in hourly steps and is displayed on the screen. When the appliance is switched on, press the timer button . The timer indicator (11) and the time indicator flash on the screen. You can now set the desired time until automatic switch-off. Then press any button (except the ON/OFF button) or wait 5 seconds to exit the setting. After the timer has been activated, the remaining time until switch-off and the currently set speed are displayed alternately on the screen at intervals of 10 seconds. The corresponding indicator light (11/6) lights up in each case. As soon as the time has elapsed, the appliance switches off automatically and goes into standby mode.

Selecting wind mode

After switching on the appliance, press the wind mode button several times to set the desired mode. Pressing the wind mode button several times cycles through the modes in the following order:
Normal wind > Natural wind > Sleep wind > Normal wind.
The corresponding indicator lights up.

Normal wind:

In normal wind mode, the appliance runs at the set speed level (Low, Medium or High) without any changes.

Natural wind:

The wind diagram of this mode is shown in the figure below:

STRONG

MIDDLE

WEAK

In natural wind mode, the corresponding indicator (7) lights up. The screen only shows the original wind speed, changes are not displayed. This means that if, for example, the natural wind mode with high speed has been activated, only the speed level “High” (“3”) is displayed without changing.

Sleep wind:

When the sleep wind mode is activated, the appliance initially continues to run at the previously set wind speed. After 30 minutes, it is reduced at 30-minute intervals. This mode is intended to prevent people who fall asleep from feeling uncomfortable due to the appliance`s speed setting being too high.

a) If the sleep wind mode has been activated at high speed, the appliance switches to medium speed after 30 minutes. The corresponding indicator lights up. After another 30 minutes of running at medium speed, the appliance switches to low speed. The corresponding indicator lights up. The appliance then continues to run at low speed until the timer expires or the appliance is switched off.
b) If the sleep wind mode has been activated at medium speed, the appliance switches to low speed after 30 minutes. The corresponding indicator lights up. The appliance then continues to run at low speed until the timer expires or the appliance is switched off.
c) If the low speed sleep wind mode has been activated, the corresponding indicator lights up. The appliance continues to run at low speed until the timer expires or the appliance is switched off.

Cooling/humidification mode

While the appliance is switched on, press the cooling/humidification mode button to switch the cooling function on and off. The corresponding indicator (9) lights up.

Turning the screen and indicators off/on (remote control)

When the appliance is on, you can press the screen off button on the remote control to turn off the screen and all indicator lights. When the screen is off and you press the screen off button or any other button, the indicator lights come back on but the other button function is not performed. Press the desired button again to perform the corresponding button function.

Negative ion function

When you switch on the appliance, the negative ion function is activated and the corresponding LED indicator (4) lights up. When you switch off the appliance, the negative ion function is deactivated.

WIFI function

With the appliance switched on, press and hold the wind mode/WIFI button for five seconds. A beep is heard and the WIFI indicator (10) flashes rapidly for five seconds. Apps on the network can be configured in standard mode. If no connection is established within 3 minutes, the WIFI indicator (10) goes out. To reconnect, press the wind mode/WIFI button again. A beep is heard, the WIFI module is reset, the WIFI indicator flashes rapidly for five seconds. Apps on the network can be configured in standard mode. Press and hold the wind mode/WIFI button again for 5 seconds as soon as the WIFI indicator (10) flashes. A beep is heard and the WIFI indicator (10) flashes slowly for 5 seconds. Apps on the network can now be configured in compatibility mode.

Notes on using the WIFI function

• If the appliance is turned off within 10 seconds after it is turned on, the WIFI indicator (10) returns to the status before it was turned off. If the appliance is turned off after 10 seconds, the WIFI indicator (10) turns off and enters power-saving mode. Press and hold the setting button for 5 seconds to restart.

• If the network is not configured within three minutes, the WIFI indicator (10) goes off. Press and hold the setting button for 5 seconds to restart.

• If the router is switched off after the WIFI connection has been successfully established, the WIFI indicator (10) also goes out. As soon as the router is switched on again, the connection to the appliance is automatically re-established.

• When using the WIFI function, the WIFI indicator (10) must flash quickly. A router (must be able to connect to external networks) and a mobile device (e.g. smartphone) are required to use the Klarstein app. The Klarstein app must be installed on the mobile end device that is also connected to the WIFI network.

DEVICE CONTROL BY SMARTPHONE

If you integrate the device into your home WiFi, you can conveniently operate it via the associated Klarstein app. The app not only allows you to remotely control the device via your smartphone, but also gives you access to recipes and additional information.

Follow these steps to connect your smartphone to your Klarstein device:

1. Download the Klarstein app first by scanning the QR code with your smartphone (see below), or download it directly from App Store or Google Play.
2. Make sure your smartphone is connected to the same WiFi network that your Klarstein device is to be connected to.
3. Open the Klarstein app.
4. Sign in to your account. If you do not have an account, sign up in the Klarstein app.
5. Follow the instructions from the app.

App Download

Use the scan function of your smartphone to scan the QR code and save the app on your smartphone.

Note: The app provides further information on how to use the app and help on how to connect to your device as soon as you open it for the first time.

iOS

| Android
---|---
|

Troubleshooting connection problems

If your Klarstein device cannot be found in the WLAN, check the following:

• Is the device plugged in?
• Is the WiFi feature of my phone enabled?
• Is the WiFi function of the Klarstein device activated? (Follow the instructions in the app)
• Has the WLAN password been entered correctly?
• Are the router, Klarstein device and smartphone in the immediate vicinity during the connection attempt? (Ideally no more than 5 m apart)
• If you have deactivated the 2.4 GHz band in the settings of your wireless router, activate it in your router settings.

Note: For further help, follow the instructions in the app when setting up the connection.

PROTECTIVE FUNCTIONS

Water shortage protection switch

If the water pump runs for 60 seconds and the software detects that the water level switch is disconnected (water shortage) for 5 consecutive seconds (65 seconds in total), the water pump automatically stops running and the appliance beeps 10 times.

Water level detection

Within 10 seconds of switching on, press and hold the cooling/humidification mode button after hearing the beep. The water level is then detected within 3 seconds. If there is no water in the water tank, the cooling function is deactivated and the appliance beeps 10 times. The water level detection is deactivated after pressing the ON/OFF button or in the event of a power failure.

Memory function

1. If the appliance is not disconnected from the power supply, when it is switched on again, the appliance will continue to run in the mode that was set before it was switched off. Sleep wind, dry wind and timer modes are not saved.
2. If the appliance is not disconnected from the power, when it is switched on again, it first runs at medium speed for 3 seconds and then changes to the speed set before it was switched off.

FILLING THE WATER TANK

Fill water into the water tank when using the cooling and humidifying function. Before filling, rotate the winding frame 90° respectively. Pull out the water tank halfway. Pour the water slowly into the water tank. After filling, push the water tank back into the appliance. Rotate the winding frame to the original position.

Water tank lock knob is locked

Water tank lock knob is unlocked

Water tank is drawn out for water filling

When filling water into the water tank, pay attention to the water level indicator:

1. When filling manually, make sure that the water level is above the minimum indicator and below the maximum indicator.
2. Only use clean drinking water.
3. When the appliance is used for the first time, there may be a slight smell and the water in the water tank may be slightly discoloured. This is normal and harmless and has no effect on your health.
4. When inserting the ice box, make sure that the maximum indicator is not exceeded.

CLEANING AND CARE

Cleaning

• Before cleaning the appliance, switch it off and disconnect the mains plug from the socket.
• Do not use chemicals, petrol, thinners or other substances that could damage the surface of the appliance to clean it.
• Remove dust with a soft cloth. For stubborn stains, use a little water (below 50 °C) and a neutral detergent. Then rub the surface of the unit dry with a soft cloth.

Filter cleaning

Clean the filters at least once a month. To do this, proceed as follows:

1. Pull the mains plug out of the socket.
2. First remove the rear ventilation grille and then the filter.
3. Let the filter soak in a soap solution for a few minutes, then clean it and let it dry.

4. Put the filter and the rear ventilation grille back into the appliance when both are completely dry.

Cleaning the water tank

• Pull the mains plug out of the socket. Turn the winding frame knob to the horizontal position and pull the water tank halfway out.
• Put your hand into the water tank, rotate the fixing buckle 90°, and then push the water pump box assembly down to take it out, and finally take out the water tank.
• Remove limescale residues in the water tank with a damp cloth soaked in neutral detergent. Then rinse the water tank with clear water.

Cleaning the surface

• Before cleaning the appliance housing, make sure that the appliance is switched off and the mains plug has been removed from the socket.
• Wipe the surface with a damp cloth. Do not rinse it directly with water.
• Do not use aggressive or abrasive cleaning agents.

Storage

• If the appliance will not be used for a long time, unplug it from the mains and pack it away to prevent dust from getting into the housing.

• Before storing the appliance, make sure that it is clean, the filter is dry and that there is no water in the water tank.

• After packing, store it in a dry, ventilated place.

DISPOSAL CONSIDERATIONS

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.

This product contains batteries. If there is a legal regulation for the disposal of batteries in your country, the batteries must not be disposed of with household waste. Find out about local regulations for disposing of batteries. By disposing of them in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences.

DECLARATION OF CONFORMITY

Manufacturer:
Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.

Importer for Great Britain:
Berlin Brands Group UK Ltd
PO Box 1145
Oxford, OX1 9UW
United Kingdom

Hereby, Chal-Tec GmbH declares that the radio equipment type Skytower 360° Smart is in compliance with Directive 2014/53/ EU. The full text of the EU declaration of conformity is available at the following internet address: use.berlin/10035818

For Great Britain: Hereby, Chal-Tec GmbH declares that the radio equipment type Skytower 360° Smart is in compliance with the relevant statutory requirements. The full text of the declaration of conformity is available at the following internet address: use.berlin/10035818

References

• Klarstein | Your home. Your kitchen. Your style.
• Take-e-way GmbH | take-e-back | Elektroschrott Rücknahmesystem Onlinehandel

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>