INOGENI Toggle USB 3.0 Switcher Hub User Guide

INOGENI Toggle USB 3.0 Switcher Hub

VERSION HISTORY

».
1.2| June 15, 2021| Adding block diagram.
1.3| June 22, 2021| Add GPIN level mode

TYPICAL APPLICATION

Here is a typical connection diagram used for the TOGGLE device in a video conferencing setup.

BLOCK DIAGRAM

Here is a simple block diagram of the TOGGLE unit.

DEVICE INTERFACES

Here are the devices interfaces.

1. RS232 and GPIN interfaces
2. 3 x USB-A ports for devices
3. PC #1 USB-B port
4. PC #2 USB-B port
5. Push-button
6. +12V power input
7. PC #1 led indicator
8. PC #2 led indicator
9. Power indicator

LEDS BEHAVIOR

Here are the leds behavior:

IMPORTANT: If all leds are blinking in sync, this means the unit is in the upgrade process. This happens only while you upgrade the unit.

OPERATING MODES

There are two modes supported by the device. They will be explained here.

Automatic

This is the default mode. This mode will switch automatically to the last PC1 connected. If the current PC is disconnected, the device will switch back to the other PC if it is detected. Push-button action and remote control are also supported.

Manual

The manual mode will enable you to force a specific PC selection. Push-button action and remote control are also supported. It is possible to turn OFF both PCs in manual mode.

These modes can be set through our INOGENI Control App or through the RS232 interface. The mode will be saved onboard the device.

1 PC: any host computer or laptop.

SPECIFICATIONS

Here is the complete specification.

Please use the Control App from INOGENI to identify the hardware revision of your product.

SERIAL COMMUNICATION PROTOCOL

Here is the complete list of commands provided through the serial connection: Pinout is indicated on the enclosure.

Baud rate: 9600 // Data bits: 8 // Stop bits: 1 // Parity: None // Flow control: None

All commands will append to the return values 2 possible answers: “ACK” or “NACK” with “/n/r” chars.

GPIN MODE

With the introduction of firmware 1.1+, there are two (2x) GPIN modes: pulse mode and level mode.

• – The GPIN pulse mode is the factory default. Each transition from HIGH to LOW on GPIN pin will force a PC change. See the following picture for the explanation of the mode.
• The GPIN level mode uses a level “0” (short to ground) and “1” (open or voltage higher than threshold) to select a specific PC.
  • A level “0” or short to ground: PC2 is selected.
  • A level “1” or open: PC1 is selected.

IMPORTANT NOTES ABOUT GPIN

• It is recommended to set the Toggle in manual mode with the UART command “sm” when using the GPIN (especially with level mode). If the Toggle is used in auto mode, any changes on the PCx side will affect the PC selected even if the GPIN level mode is used.
• It is also recommended to lock the button with the UART command “slck” when the GPIN is used in level mode.
• For Toggle with a hardware revision of 2.0, you need to connect the external power supply to use the GPIN. The Control App software from INOGENI will report the exact hardware revision.

SETTINGS

Some settings can be saved with the “SAVE” command. These settings are:

• Presence or absence of events on serial ports. Events are used for diagnostic. An event returned by the unit always starts with the string “EVT:” The “SEV” serial command is used to enable/disable the events. This command also automatically saves this setting inside the device.
• Manual or automatic mode for PC selection. The “SM” command is used to switch between manual and automatic modes. This command also automatically saves this setting inside the device.
• If manual mode is selected and the GPIN level mode is disabled: the specific PC selected is also saved. The “SH” command is used to select between PC1, PC2 or OFF. This command also automatically saves this setting inside the device.
• If the button is locked or not. The “SLCK” command is used to select between these modes. This command also automatically saves this setting inside the device.
• If the GPIN level mode is selected or not. The command “SGMOD” is used to select between these modes. This command also automatically saves this setting inside the device.
• The “DEF” command restores the default settings of the device. It will take effect immediately. The factory default settings are:

1. No events.
2. Automatic mode for PCx selection.
3. GPIN_LEVEL disabled.
4. Button unlocked.

INOGENI CONTROL APP

You can use our Control App to monitor firmware information, upgrade and configure your unit.

SUPPORT

Engineered by video professionals, for video professionals, it is your most compatible USB 3.0 device. INOGENI expertise at your fingertips:

• Expert Technical Support team at support@inogeni.com for immediate help or if you have any technical question about our products.
• Extensive Knowledge Base to learn from other customers experiences.

© Copyright 2021 by INOGENI INC. All Rights Reserved.

INOGENI name and logo are trademarks or registered trademark of INOGENI. Use of this product is subject to the terms and conditions of the license and limited warranty in effect at the time of purchase. Product specifications can change without notice.

INOGENI, Inc.
979 de Bourgogne avenue, suite 530
G1W 2L4 (QC) Canada

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>