2AXPOTWS-02 Bluetooth wireless headset User Manual

June 5, 2024
TWS

True Wireless Stereo Earbuds
Quick Start/ User’s Manual

  1. Charging
    Insert USB Type-C Cable to charge for 20 minutes2AXPOTWS 02 Bluetooth
wireless headset - 1

  2. Wear2AXPOTWS 02 Bluetooth wireless headset - 3 Note:
    Refer to P9 of Manual

  3. Connect2AXPOTWS 02 Bluetooth wireless headset - 4 Note:
    Refer to P10 of the Manual

  4. Function Definition****
    | Tap
    ---|---
    | Tap & Hold

2AXPOTWS 02 Bluetooth wireless headset - 7Refer to P11-P12 of the Manual

Package Contents

2AXPOTWS 02 Bluetooth wireless headset - 8

Product Diagram

2AXPOTWS 02 Bluetooth wireless headset - 9

  1. Charging Contact
  2. MFB/ Bouton multifunction
  3. LED Indicator & Microphone Two in One
  4. Base Charging Contact
  5. Charging Cabin
  6. Base Indicators
  7. USB Type-C Charging Port

Charging

Put into charging cabin to charge 20 minutes before using

2AXPOTWS 02 Bluetooth wireless headset - 10

When charging earbuds, both side lights of the charging cabin will flash to indicate which side is charging.

Turn-ON/OFF, Allumer

Auto ON
Auto OFF

2AXPOTWS 02 Bluetooth wireless headset - 13

Wear

A. Rotate the earbuds and adjust to find the best angle.
B. Make sure the ear tip seal in the ear canal.

2AXPOTWS 02 Bluetooth wireless headset - 14

Connect to Device

Shall be taken out of the charging cabin to connect with your device.

Function Definition

Music Control

| On Tap
---|---
Play/Pause,
| Double Tap
Volume down(L) / Volume up(R)
| Triple Tap
Turn On/Off Voice Assistant
| Hold (2s)
Previous song (L) /Next song (R)

Communication

| On Tap
---|---
Answer a Call/ End a Call,
| Hold (2s)
Reject Incoming Cal

Indicator Light

2AXPOTWS 02 Bluetooth wireless headset - 22

| Charging
---|---
| Fully-charged

Put charging cabin on Wireless Charging Pad to charge wirelessly.
Note: Qi-certificated Wireless Charging Pad shall be purchased by yourself

Open the cabin to check the remaining power.

2AXPOTWS 02 Bluetooth wireless headset - 25

Parameters Paramètre

Chipset: Qualcomm QCC3020

Bluetooth
Version: 5.0
Profiles: HFP, HSP, A2DP, AVRCP
Coding: SBC, AAC, apt-X
Transmission Distance: >20 meters

Battery Spec.

Earbuds: 65mAh
Charging Time: 60 min
Continuous Play Time: ≈8h (Vol 75%)

Charging Cabin

Battery: 430mAh
Charging Time: 60 min
Refer Times to Charge Earbuds: 2.5 times
Charging Input: 5V 500mA

Driver Units: φ6 mm

Microphone: MEMS

Range of Frequency

Earbuds: 20Hz – 20kHz
Sensitivity: 98dB ±3
Microphone: -38dBV ±1
CVC Noise Cancellation: 8.0

Endurance
IPX5 Water Resistent(Earbuds Only)
Working Temperature: -10℃ ~ +50℃
Storage temperature: -20℃ ~ +50℃
Humidity: 10℃ ~ 35℃

All things are subject to the data of the laboratory, for reference only.

Maintenance

Regularly clean your earbuds to make sure that they will last for a longer lifespan. Do not use alcohol, thinners, or other solvents for cleaning purposes.

– Wipe the touch panel with a dry cloth.
– Wipe your charging contacts with a clean cloth after use in case there is dirt.
– Do not expose it to the sun or high heat. High heating will shorten the lifespan of electronic components, damage batteries, and deform some plastic parts.
– Do not put it in cold circumstances to avoid damaging the PCB board.
– Do not attempt to take apart the product, especially non-professionals.
– Do not fall, vibrate strongly. Strike with hard objects, to avoid damage inner electronic circuit.
– Do not scratch the surface with sharp items to avoid damage case and appearance.
– Charge once a month to extend lifespan.

FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals