JBC CD-1SQF 100V Precision Soldering Station Instruction Manual

JBC CD-1SQF 100V Precision Soldering Station

Packing List

The following items are included:

Features and Connections

Adjustable Stand

• Adjust the tool stand to suit your work position.
• The Cable Collector keeps the cable away from the work area and prevents the weight of the cable from disturbing the operator while soldering.

Removing the Splashguard

1.  Unlock the splashguard.
2.  Lift off

Wiper

• Tapping: Tap gently to remove excess solder.
• Wiping: Use the slots to remove the remaining particles.
• Wiper Ref. CL0160 The softest cleaning method. Keep the sponge damp with distilled water when working to avoid tip wear.

Changing the Grips

• Easily replace the grips using the slip-on tabs.
• Note: For the different handles are different grips available.

Sealing Plug Replacement

The sealing plug prevents undesirable flux vapors or particles from entering inside the tool. Its usage is highly recommended for intensive applications when soldering is exposed to FOD environments or for applications where the soldering iron works close to vertical position. Note: For the different handles are different sealing plugs available.

1.  Removing Sealing Plug
2.  Mounting Position
3.  Inserting Sealing Plug

• Enter, not deeper than 8mm, a small shaft or screwdriver and lift and pull the sealing plug. Never use a cartridge to do this operation.

1. * Note: The chamfered side has to be positioned towards the handle.

   • Push the sealing plug inside the handle until the sealing plug and handle edges are aligned.

Quick Tip Changer

1.  Removing|
2.  Inserting
3.  Fixing

*Important: It is essential to insert the cartridges as far as the mark for a proper connection

Compatible Cartridges

The CD-B stations work with C245 cartridges and T245 handles. Find the model that best suits your soldering needs at www.jbctools.com

Operation

The JBC Most Efficient Soldering System
This revolutionary technology is able to recover tip temperature extremely quickly. This allows the user to work at a lower temperature. As a result, tip life increases by 5.

1.  Work
2.  Sleep
3.  Hibernation
   • When the tool is lifted from the stand the tip will heat up to the selected temperature.
   • When the tool is in the stand, the temperature falls to the preset sleep temperature.
   • After longer periods of inactivity, the power is cut off and the tool cools down to room temperature.

Control Process

Work Screen

Parameters

Be careful when using these parameters as they may reduce the tip life if not used properly. Please follow the recommended guidelines:
Station Settings

Tool Settings

USB Connector

Download the latest software from our website to improve your soldering station.
JBC Updater
www.jbctools.com/software.html Update the station software via USB connection:

JBC Web Manager
www.jbctools.com/manager.html
Manage and monitor as many stations as your PC can handle by using the JBC Web Manager. You can export data to another PC.

Maintenance

Before carrying out maintenance, always switch the device off and disconnect it from the mains. Allow the equipment to cool down.

•  Clean the station screen with a glass cleaner or a damp cloth.
•  Use a damp cloth to clean the casing and the tool. Alcohol can only be used to clean the metal parts.
•  Periodically check that the metal parts of the tool and stand are clean so that the station can detect the tool status.
•  Maintain tip surface clean and tinned prior to storage in order to avoid tip oxidation. Rusty and dirty surfaces reduce heat transfer to the solder joint.
•  Periodically check all cables and tubes.
•  Replace any defective or damaged pieces. Only use original JBC spare parts.
•  Replace a blown fuse as follows:
  •  Pull off the fuse holder and remove the fuse. If necessary use a tool to lever it off.
  •  Insert the new fuse into the fuse holder and return it to the station.

Safety

•  Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.
•  The power cord must be plugged into approved bases. Be sure that it is properly grounded before use. When unplugging it, hold the plug, not the wire.
•  Do not work on electrically live parts.
•  The tool should be placed in the stand when not in use in order to activate the sleep mode. The soldering tip, the metal part of the tool and the stand may still be hot even when the station is turned off. Handle with care, including when adjusting the stand position.
•  Do not leave the appliance unattended when it is on.
•  Do not cover the ventilation grills. Heat can cause inflammable products to ignite.
•  Avoid flux coming into contact with skin or eyes to prevent irritation.
•  Be careful with the fumes produced when soldering.
•  Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
•  Utmost care must be taken with liquid tin waste which can cause burns.

Specifications

•  Output Peak Power CD-SF: 40W
•  Temperature Range: 90 – 450 °C / 190 – 840 °F
•  Idle Temp. Stability (still air): ±1.5ºC 7 ±3ºF (Meets and exceed IPC J-STD-001)
•  Temp. accuracy: ±3% (Using reference cartridge)
•  Temp. adjustment: ±50ºC / ±90ºF (Through station menu setting)
•  Tip to ground voltage/resistance: Meets and exceed ANSI/ESD S20.20-2014 IPC J-STD-001F
•  Earthing Fuse: F 1.25A
•  Connections: USB connector station-PC RJ12 Connector
•  Ambient operating temp: 10 – 50 ºC / 50 – 122 ºF
•  Control Unit Dimensions / Weight: 170 x 176 x 145 mm / 2.8 kg (L x W x H) 6.7 x 6.9 x 5.7 in / 6.17 lb
•  Total Net Weight: 3 kg / 6.61 lb
•  Total Package Dimensions / Weight: 234 x 234 x 258 mm / 3.15 kg (L x W x H) 9.2 x 9.2 x 10.2 in / 6.94 lb

References

• JBC Soldering Stations, Irons and Rework equipment for electronics
• Manager DOWNLOAD
• Warranty Extension

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>