QoQa Luke Roberts Smart Pendant Light Luvo Instruction Manual

: June 3, 2024
: QoQa

Table of Contents

QoQa Luke Roberts Smart Pendant Light Luvo
PRODUCT SPECIFICATION
WARNINGS & SAFETY INSTRUCTIONS
PACKAGE CONTENTS
INSTALLATION REQUIREMENTS
REMOVING THE LUMINAIRE
Documents / Resources

QoQa Luke Roberts Smart Pendant Light Luvo

QoQa-Luke-Roberts-Smart-Pendant-Light-Luvo-
product

HELLO & WELCOME
This instruction manual shows you how to install, handle and remove your new luminaire. Please read this manual carefully before using the luminaire.

PRODUCT SPECIFICATION

LUMINAIRE

Directional light source with non-replaceable LEDs, max. 4402 lm (in a wide cone 120°):
Colour-tuneable 2700-4000 K, CRI > 92
Direct: 84 spots, max. 4402 lm
Indirect: 16 segments, RGBWW color mix, max. 1400 lm
Sensors: optical and acoustic
Wireless connection: Bluetooth® 4.2 LE
Smart luminaire size: ∅30 cm x 8 cm
Ceiling mount size: ∅13 cm x 5.7 cm
Weight incl. ceiling mount: 2.8 kg
Environment: IP20, 10°-35° C, no contact with water, RH < 85 % (non-condensing)

ELECTRICS

Power supply rated input: 230 V AC, 50 Hz
Luminaire rated input: 12 V DC, max. 5 A
Standby power: 0.5 W
Rated power: max. 63 W in full load
Insulation class: class II

WARNINGS & SAFETY INSTRUCTIONS

Use this luminaire only for indoors; dry conditions only.
Use the luminaire only in the allowed environment and temperature range.
The luminaire is not a toy and not designed to be played with by children.
Do not stare directly into the light source.
Do not pull on the hanging luminaire.
Do not attach anything to the luminaire except authorized Luke Roberts accessories.
Only a qualified electrician should install the luminaire.
The LED module of the luminaire cannot be replaced – don’t disassemble the luminaire without authorization.
Make sure to switch off mains power when installing the luminaire.
This luminaire does not work in combination with a dimmer.
The luminaire will produce heat. Allow proper airflow around it.
The luminaire’s flexible cable can only be replaced by the manufacturer or an authorized service agent.

CLEANING

Switch off the luminaire and let it cool down to room temperature before cleaning it.
Use the (dry) microfiber cloth supplied with the luminaire to clean the surface.
Do not use water or any chemicals.
Regularly remove dust from the luminaire’s heat sink to ensure proper airflow.

DISPOSAL

For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.

LIMITED WARRANTY

Luke Roberts warrants that this device will
be free from defects in material and workmanship and will operate for 2 years when used and installed as directed.
If this device does not conform to the warranty, Luke Roberts will send you, at its discretion, a replacement device or refund your original price upon receipt of the
returned device, register receipt, and proof of purchase.
Please contact Luke Roberts support to find out how to return the device.
This limited warranty does not cover defects caused by the customer.

Luke Roberts« is a registered trademark of the LR Innovation Lab GmbH.

Google Play and the Google Play logo are trademarks of Google LLC.
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by LR Innovation Lab GmbH is under license. Other trademarks and trade names are those of their respective owners.
Apple, the Apple logo, iPhone, and iPad are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc., registered in the U.S. and other countries.

SUPPORT
If you have any questions or highly welcomed feedback, our customer support team is happy to help at support@luke-roberts.com.
Please also visit our website for more helpful tips and information about this product:

PACKAGE CONTENTS

QoQa-Luke-Roberts-Smart-Pendant-Light-Luvo-
FIG-1

A Luminaire
B Ceiling Mount
C Accessories

INSTALLATION REQUIREMENTS

Check that no dimmer is present in the mains circuit that will power the luminaire.
Ceiling mount needs to be mounted on a flat ceiling surface withstanding up to 70° C.
Keep enough space around the luminaire and ceiling mount in order to maintain proper airflow.
Please use the appropriate fastening method for your type of ceiling.
Make sure to hang the luminaire at least 20 cm below the ceiling mount.
Excess cable can be stored in the ceiling mount.

Fasten power supply to the ceiling using three screws.
- Be careful not to scratch the mains wires and use fiberglass wire sleeving if required.
If a ceiling outlet box is used, make sure it can hold the luminaire’s weight (2.8 kg).
- Plug mains wires into the primary side connector marked with
- Connect the wires according to the connector markings: L, N
- If you have purchased the Luke Roberts BLOOM lampshade, please refer to the lampshade’s installation manual now.
Prepare the luminaire for installation by first pulling the cable through the ceiling mount cap.
- Then guide the cable through the adjusting plate.
- Make sure that you don’t harm the cable.
- Now decide on the height of the luminaire. Move the plate along the cable until you have reached your desired cable length.
Insert the cable stopper into the adjusting plate.
- This is the primary fixing mechanism for the luminaire and cable. Please check the stopper is placed accurately.
- For further assembly, you can now hold the luminaire by the cable without changing its length.
Attach the luminaire to the power supply on the ceiling by pushing the adjusting plate into the hooks in the middle.
- Push until it has snapped in properly.
Wind up the excess cable around the plate before you continue connecting the luminaire.
Connect the luminaire’s cable to the secondary connector marked
- Make sure that the colours of the wires match with the connector positions:
- ⊙ violet | ⊖ black | ⊕ red
- The violet wire is optional and may not be available on all luminaires.
Push up the cap towards the ceiling.
- Make sure to find the correct position when doing so.
- There are three snaps to which the cap gets attached to the power supply.
When the cap is in the correct position, lock it by turning it clockwise until it locks in.
- Remove the protective film from the uplight diffuser.
Switch on the mains power supply, and your luminaire will light up.
- To use all the features of your new smart luminaire, connect it to the Luke Roberts App.
- It is available for iPhone and iPad on the Apple App Store or for your Android device on the Google Play Store.
- If you have any questions or problems, please go here:

REMOVING THE LUMINAIRE

Before proceeding, make sure the mains power is disconnected

Turn the cap anticlockwise to unfasten it.
Take a flat screwdriver and push it into the connectors to disconnect the wires.
By pressing the two pins on top of the adjusting plate, you loosen the plate so that you can take out the luminaire.
To remove the power supply, loosen the three screws from the ceiling.

EC Conformity
The products contained herein are in conformity with the essential requirements of the following European Directives and harmonized standards.

Low Voltage Directive 2014/35/EU:
EN 60598-1, EN 60598-2-1, EN 61347-2-13
EN 62031, EN 62493, EN 62311, EN 61347-1
EMC Directive 2014/30/EU:
EN 55015, EN 61547, EN 61000-3-2,
EN 6100-4-X
Artificial Optical Radiation Directive 2006/25/EC: EN 62471-5
Radio Equipment Directive 2014/53/EU:
EN 301 489-17, EN 300 328-2, EN 301 489-1 EcoDesign Directive 2009/125/EC,
EU/2019/2020
Restriction of Hazardous Substances Directive 2011/65/EU

Your way to smarter lighting
LUKE-ROBERTS.COM

LR Innovation Lab GmbH, Spittelberggasse 3/15, 1070 Vienna, Austria | support @luke-roberts.com | @Luke Roberts Lighting Luke Roberts LRF01 Manual EU-V06 | ©2022 LR Innovation Lab GmbH | All rights reserved.

Documents / Resources

| QoQa Luke Roberts Smart Pendant Light Luvo [pdf] Instruction Manual
Luke, Roberts Smart Pendant Light Luvo, Luke Roberts Smart Pendant Light Luvo, Smart Pendant Light Luvo, Pendant Light Luvo, Light Luvo
---|---